Home
last modified time | relevance | path

Searched +full:keep +full:- +full:pll +full:- +full:enabled (Results 1 – 6 of 6) sorted by relevance

/Documentation/devicetree/bindings/net/
Dqca,ar803x.yaml1 # SPDX-License-Identifier: GPL-2.0+
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Andrew Lunn <andrew@lunn.ch>
11 - Florian Fainelli <f.fainelli@gmail.com>
12 - Heiner Kallweit <hkallweit1@gmail.com>
18 - $ref: ethernet-phy.yaml#
21 qca,clk-out-frequency:
26 qca,clk-out-strength:
31 qca,disable-smarteee:
[all …]
Dmotorcomm,yt8xxx.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Frank Sae <frank.sae@motor-comm.com>
13 - $ref: ethernet-phy.yaml#
18 - ethernet-phy-id4f51.e91a
19 - ethernet-phy-id4f51.e91b
21 rx-internal-delay-ps:
24 internal delay (phy-mode is 'rgmii-id' or 'rgmii-rxid') in pico-seconds.
30 tx-internal-delay-ps:
[all …]
/Documentation/driver-api/media/
Dcamera-sensor.rst1 .. SPDX-License-Identifier: GPL-2.0
8 This document covers the in-kernel APIs only. For the best practices on
12 CSI-2, parallel and BT.656 buses
13 --------------------------------
15 Please see :ref:`transmitter-receiver`.
18 ---------------
20 Camera sensors have an internal clock tree including a PLL and a number of
29 elsewhere. Therefore only the pre-determined frequencies are configurable by the
35 Read the ``clock-frequency`` _DSD property to denote the frequency. The driver
41 The preferred way to achieve this is using ``assigned-clocks``,
[all …]
/Documentation/devicetree/bindings/net/dsa/
Dqca8k.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - John Crispin <john@phrozen.org>
13 If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode
16 ID. To declare the internal mdio-bus configuration, declare an MDIO node in
18 PHY it is connected to. In this config, an internal mdio-bus is registered and
20 mdio-bus configurations are not supported by the hardware.
27 - enum:
28 - qca,qca8327
[all …]
/Documentation/driver-api/thermal/
Dintel_dptf.rst1 .. SPDX-License-Identifier: GPL-2.0
12 ------------
31 ----------------------------
43 "42A441D6-AE6A-462b-A84B-4A8CE79027D3" : Passive 1
45 "3A95C389-E4B8-4629-A526-C52C88626BAE" : Active
47 "97C68AE7-15FA-499c-B8C9-5DA81D606E0A" : Critical
49 "63BE270F-1C11-48FD-A6F7-3AF253FF3E2D" : Adaptive performance
51 "5349962F-71E6-431D-9AE8-0A635B710AEE" : Emergency call
53 "9E04115A-AE87-4D1C-9500-0F3E340BFE75" : Passive 2
55 "F5A35014-C209-46A4-993A-EB56DE7530A1" : Power Boss
[all …]
/Documentation/admin-guide/
Dkernel-parameters.txt16 force -- enable ACPI if default was off
17 on -- enable ACPI but allow fallback to DT [arm64,riscv64]
18 off -- disable ACPI if default was on
19 noirq -- do not use ACPI for IRQ routing
20 strict -- Be less tolerant of platforms that are not
22 rsdt -- prefer RSDT over (default) XSDT
23 copy_dsdt -- copy DSDT to memory
24 nospcr -- disable console in ACPI SPCR table as
41 If set to vendor, prefer vendor-specific driver
65 CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
[all …]