Searched full:leave (Results 1 – 25 of 166) sorted by relevance
1234567
| /Documentation/ABI/testing/ |
| D | sysfs-class-power-rt9467 | 12 only 'VBUS' or 'Power key" pressed can make it leave this mode.
13 'Disable' also can help to leave it, but it's more like to
|
| D | sysfs-class-power-rt9471 | 10 shipping mode, only 'VBUS' or 'Power key" pressed can make it leave this
11 mode. 'Disable' also can help to leave it, but it's more like to abort
|
| D | sysfs-dev | 19 leave the system.
|
| D | sysfs-bus-i2c-devices-pca954x | 15 -1 leave the mux as-is, which is the most optimal
|
| /Documentation/locking/ |
| D | futex-requeue-pi.rst | 20 implementation would wake the highest-priority waiter, and leave the
49 mutex only after it has returned to user space. This will leave the
92 The requeue code cannot simply wake the waiter and leave it to
|
| /Documentation/w1/slaves/ |
| D | w1_ds28e17.rst | 47 Valid values are 100, 400, 900 [kBaud]. Any other value means to leave
59 Leave it at 1 unless you get ETIMEDOUT errors and a "w1_slave_driver
|
| /Documentation/devicetree/bindings/fpga/ |
| D | fpga-bridge.yaml | 20 Default is to leave bridge in current state.
|
| /Documentation/devicetree/bindings/arm/mstar/ |
| D | mstar,smpctrl.yaml | 16 and a magic number that allows secondary processors to leave
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | maxim,ds2760.yaml | 26 and leave sleep Mode when the DQ line goes high.
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 29 <pinctrl-bindings.txt>. Absence of properties will leave the configuration
60 Absence of this property will leave
|
| D | pinctrl-rk805.txt | 35 <pinctrl-bindings.txt>. Absence of properties will leave the configuration
|
| /Documentation/devicetree/bindings/usb/ |
| D | usb-device.yaml | 37 but a device adhering to this binding may leave out all except
69 also be used, but a device adhering to this binding may leave out
|
| /Documentation/ABI/obsolete/ |
| D | sysfs-bus-usb | 18 If you want to suspend a device immediately but leave it
|
| /Documentation/networking/dsa/ |
| D | lan9303.rst | 29 If one of the user ports leave the bridge, the ports goes back to the initial
|
| /Documentation/filesystems/bcachefs/ |
| D | CodingStyle.rst | 27 BUG_ON(). Don't leave undefined or unspecified behavior lurking in the codebase.
31 which should be logically impossible. Leave the BUG_ON()s in for the ones which
134 Expect to throw a lot of things away, or leave them half finished for later.
|
| /Documentation/devicetree/bindings/net/can/ |
| D | tcan4x5x.txt | 31 - wakeup-source: Leave the chip running when suspended, and configure
|
| /Documentation/i2c/busses/ |
| D | i2c-ali1535.rst | 38 We make sure that the SMB is enabled. We leave the ACPI alone.
|
| /Documentation/devicetree/bindings/rtc/ |
| D | isil,isl1208.yaml | 54 Default will leave the non-volatile configuration of the pullup
|
| /Documentation/devicetree/bindings/watchdog/ |
| D | realtek,otto-wdt.yaml | 59 Reset the CPU and IPsec engine, but leave other peripherals untouched
|
| /Documentation/hwmon/ |
| D | asus_wmi_sensors.rst | 75 sensors frequently, don't leave you computer unattended. Upgrading to new
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | fsl,imx6ul-tsc.yaml | 40 low once the finger leave the touch screen (The last touch event
|
| /Documentation/firmware-guide/acpi/ |
| D | non-d0-probe.rst | 10 In some cases it may be preferred to leave certain devices powered off for the
|
| /Documentation/networking/ |
| D | bridge.rst | 216 benefit of the explicit host tracking in IGMP is to allow minimal leave
219 The length of time between a host wanting to leave and a device stopping
220 traffic forwarding is called the IGMP leave latency. A device configured
223 indicates that it no longer wants to receive traffic. The leave latency
|
| /Documentation/i2c/ |
| D | slave-testunit-backend.rst | 135 - leave out, partial command!
165 - leave out, partial command!
|
| /Documentation/devicetree/bindings/regulator/ |
| D | tps65090.txt | 27 "overcurrent wait" field and we'll leave it to the BIOS/EC to deal with.
|
1234567