Home
last modified time | relevance | path

Searched +full:led +full:- +full:mode (Results 1 – 25 of 114) sorted by relevance

12345

/Documentation/devicetree/bindings/leds/
Dleds-lm3532.txt1 * Texas Instruments - lm3532 White LED driver with ambient light sensing
4 The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
5 programmable over an I2C-compatible interface and has independent
7 method allows for different LED currents in each current sink thus allowing
11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
16 - compatible : "ti,lm3532"
17 - reg : I2C slave address
18 - #address-cells : 1
19 - #size-cells : 0
22 - enable-gpios : gpio pin to enable (active high)/disable the device.
[all …]
Dleds-lp55xx.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/leds-lp55xx.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI/National Semiconductor LP55xx and LP8501 LED Drivers
10 - Jacek Anaszewski <jacek.anaszewski@gmail.com>
11 - Pavel Machek <pavel@ucw.cz>
15 LED Drivers.
27 - national,lp5521
28 - national,lp5523
[all …]
Drichtek,rt8515.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Richtek RT8515 1.5A dual channel LED driver
10 - Linus Walleij <linus.walleij@linaro.org>
13 The Richtek RT8515 is a dual channel (two mode) LED driver that
14 supports driving a white LED in flash or torch mode. The maximum
15 current for each mode is defined in hardware using two resistors
22 enf-gpios:
26 ent-gpios:
[all …]
Dleds-powernv.txt2 -------------------------------------------------
5 - compatible : Should be "ibm,opal-v3-led".
6 - led-mode : Should be "lightpath" or "guidinglight".
9 form of a sub-node.
12 - led-types : Supported LED types (attention/identify/fault) provided
18 compatible = "ibm,opal-v3-led";
19 led-mode = "lightpath";
21 U78C9.001.RST0027-P1-C1 {
22 led-types = "identify", "fault";
Dmaxim,max77693.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Krzysztof Kozlowski <krzk@kernel.org>
16 There are two LED outputs available - FLED1 and FLED2. Each of them can
17 control a separate LED or they can be connected together to double the
18 maximum current for a single connected LED. One LED is represented by one
26 const: maxim,max77693-led
28 maxim,boost-mode:
30 In boost mode the device can produce up to 1.2A of total current on both
[all …]
Dcommon.yaml1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jacek Anaszewski <jacek.anaszewski@gmail.com>
11 - Pavel Machek <pavel@ucw.cz>
14 LED and flash LED devices provide the same basic functionality as current
15 regulators, but extended with LED and flash LED specific features like
16 blinking patterns, flash timeout, flash faults and external flash strobe mode.
18 Many LED devices expose more than one current output that can be connected
19 to one or more discrete LED component. Since the arrangement of connections
[all …]
Dsprd,sc2731-bltc.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/leds/sprd,sc2731-bltc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Orson Zhai <orsonzhai@gmail.com>
11 - Baolin Wang <baolin.wang7@gmail.com>
12 - Chunyan Zhang <zhang.lyra@gmail.com>
16 red LED, green LED and blue LED. Each LED can work at normal PWM mode
17 or breath light mode.
21 const: sprd,sc2731-bltc
[all …]
Dleds-lm3601x.txt1 * Texas Instruments - lm3601x Single-LED Flash Driver
3 The LM3601X are ultra-small LED flash drivers that
7 - compatible : Can be one of the following
10 - reg : I2C slave address
11 - #address-cells : 1
12 - #size-cells : 0
15 - reg : 0 - Indicates a IR mode
16 1 - Indicates a Torch (white LED) mode
18 Required properties for flash LED child nodes:
20 - flash-max-microamp : Range from 11mA - 1.5A
[all …]
Dkinetic,ktd2692.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: KTD2692 Flash LED Driver from Kinetic Technologies
10 - Markuss Broks <markuss.broks@gmail.com>
13 KTD2692 is the ideal power solution for high-power flash LEDs.
14 It uses ExpressWire single-wire programming for maximum flexibility.
16 The ExpressWire interface through CTRL pin can control LED on/off and
17 enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current,
21 LED current will be ramped up to the flash-mode current level.
[all …]
Dleds-mt6360.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/leds-mt6360.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: LED driver for MT6360 PMIC from MediaTek Integrated.
10 - Gene Chen <gene_chen@richtek.com>
15 Add MT6360 LED driver include 2-channel Flash LED with torch/strobe mode,
16 and 4-channel RGB LED support Register/Flash/Breath Mode
20 const: mediatek,mt6360-led
22 "#address-cells":
[all …]
Dleds-netxbig.txt5 - compatible: "lacie,netxbig-leds".
6 - gpio-ext: Phandle for the gpio-ext bus.
9 - timers: Timer array. Each timer entry is represented by three integers:
10 Mode (gpio-ext bus), delay_on and delay_off.
12 Each LED is represented as a sub-node of the netxbig-leds device.
14 Required sub-node properties:
15 - mode-addr: Mode register address on gpio-ext bus.
16 - mode-val: Mode to value mapping. Each entry is represented by two integers:
17 A mode and the corresponding value on the gpio-ext bus.
18 - bright-addr: Brightness register address on gpio-ext bus.
[all …]
/Documentation/devicetree/bindings/leds/backlight/
Dlm3630a-backlight.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/backlight/lm3630a-backlight.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI LM3630A High-Efficiency Dual-String White LED
10 - Lee Jones <lee@kernel.org>
11 - Daniel Thompson <daniel.thompson@linaro.org>
12 - Jingoo Han <jingoohan1@gmail.com>
15 The LM3630A is a current-mode boost converter which supplies the power and
26 '#address-cells':
[all …]
Dti,lm3509.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI LM3509 High Efficiency Boost for White LED's and/or OLED Displays
10 - Patrick Gansterer <paroga@paroga.com>
13 The LM3509 current mode boost converter offers two separate outputs.
23 "#address-cells":
26 "#size-cells":
29 reset-gpios:
32 ti,brightness-rate-of-change-us:
[all …]
/Documentation/ABI/testing/
Dsysfs-class-led-driver-lm35331 What: /sys/class/leds/<led>/als_channel
7 ALS-current-control mode (1, 2), where:
14 What: /sys/class/leds/<led>/als_en
19 Enable ALS-current-control mode (0, 1).
21 What: /sys/class/leds/<led>/falltime
22 What: /sys/class/leds/<led>/risetime
40 What: /sys/class/leds/<led>/id
45 Get the id of this led (0..3).
47 What: /sys/class/leds/<led>/linear
52 Set the brightness-mapping mode (0, 1), where:
[all …]
Dsysfs-class-led-flash1 What: /sys/class/leds/<led>/flash_brightness
6 Set the brightness of this LED in the flash strobe mode, in
7 microamperes. The file is created only for the flash LED devices
11 /sys/class/leds/<led>/max_flash_brightness.
13 What: /sys/class/leds/<led>/max_flash_brightness
18 Maximum brightness level for this LED in the flash strobe mode,
21 What: /sys/class/leds/<led>/flash_timeout
28 of the strobe. The file is created only for the flash LED
31 What: /sys/class/leds/<led>/max_flash_timeout
36 Maximum flash timeout for this LED, in microseconds.
[all …]
Dsysfs-class-led-trigger-netdev1 What: /sys/class/leds/<led>/device_name
4 Contact: linux-leds@vger.kernel.org
8 What: /sys/class/leds/<led>/interval
11 Contact: linux-leds@vger.kernel.org
13 Specifies the duration of the LED blink in milliseconds.
18 Trying to set any value in this specific mode will return
21 What: /sys/class/leds/<led>/link
24 Contact: linux-leds@vger.kernel.org
28 If set to 0 (default), the LED's normal state is off.
30 If set to 1, the LED's normal state reflects the link state
[all …]
/Documentation/userspace-api/media/v4l/
Dext-ctrls-flash.rst1 .. SPDX-License-Identifier: GFDL-1.1-no-invariants-or-later
3 .. _flash-controls:
13 The interface can support both LED and xenon flash devices. As of
17 .. _flash-controls-use-cases:
23 Unsynchronised LED flash (software strobe)
24 ------------------------------------------
26 Unsynchronised LED flash is controlled directly by the host as the
34 Synchronised LED flash (hardware strobe)
35 ----------------------------------------
37 The synchronised LED flash is pre-programmed by the host (power and
[all …]
/Documentation/devicetree/bindings/mfd/
Dtps6105x.txt3 The TP61050/TPS61052 is a high-power "white LED driver". The
4 device provides LED, GPIO and regulator functionalities.
7 - compatible: "ti,tps61050" or "ti,tps61052"
8 - reg: Specifies the I2C slave address
10 Optional sub-node:
12 This subnode selects the chip's operational mode.
15 - regulator: presence of this sub-node puts the chip in regulator mode.
18 - led: presence of this sub-node puts the chip in led mode.
20 - function : see ../leds/common.txt
21 - color : see ../leds/common.txt
[all …]
/Documentation/admin-guide/laptops/
Dlg-laptop.rst1 .. SPDX-License-Identifier: GPL-2.0+
7 By Matan Ziv-Av <matan@svgalib.org>
11 -------
15 - FN-F1 (LG control panel) - Generates F15
16 - FN-F5 (Touchpad toggle) - Generates F21
17 - FN-F6 (Airplane mode) - Generates RFKILL
18 - FN-F9 (Reader mode) - Generates F14
23 Reader mode
24 -----------
26 Writing 0/1 to /sys/devices/platform/lg-laptop/reader_mode disables/enables
[all …]
/Documentation/leds/
Dleds-class-flash.rst2 Flash LED handling under Linux
5 Some LED devices provide two modes - torch and flash. In the LED subsystem
6 those modes are supported by LED class (see Documentation/leds/leds-class.rst)
7 and LED Flash class respectively. The torch mode related features are enabled
12 must be defined in the kernel config. A LED Flash class driver must be
13 registered in the LED subsystem with led_classdev_flash_register function.
15 Following sysfs attributes are exposed for controlling flash LED devices:
16 (see Documentation/ABI/testing/sysfs-class-led-flash)
18 - flash_brightness
19 - max_flash_brightness
[all …]
Dleds-mt6370-rgb.rst1 .. SPDX-License-Identifier: GPL-2.0
4 The device for Mediatek MT6370 RGB LED
8 -----------
10 The MT6370 integrates a four-channel RGB LED driver, designed to provide a
11 variety of lighting effect for mobile device applications. The RGB LED devices
12 includes a smart LED string controller and it can drive 3 channels of LEDs with
13 a sink current up to 24mA and a CHG_VIN power good indicator LED with sink
15 PWM Dimming mode, breath pattern mode, and constant current mode. The device
16 can increase or decrease the brightness of the RGB LED via an I2C interface.
21 /sys/class/leds/<led>/hw_pattern
[all …]
Dleds-class.rst2 LED handling under Linux
5 In its simplest form, the LED class just allows control of LEDs from
7 LED is defined in max_brightness file. The brightness file will set the brightness
8 of the LED (taking a value 0-max_brightness). Most LEDs don't have hardware
9 brightness support so will just be turned on for non-zero brightness settings.
11 The class also introduces the optional concept of an LED trigger. A trigger
12 is a kernel based source of led events. Triggers can either be simple or
14 existing subsystems with minimal additional code. Examples are the disk-activity,
15 nand-disk and sharpsl-charge triggers. With led triggers disabled, the code
18 Complex triggers while available to all LEDs have LED specific
[all …]
Dleds-sc27xx.rst1 .. SPDX-License-Identifier: GPL-2.0
7 /sys/class/leds/<led>/hw_pattern
8 --------------------------------
10 Specify a hardware pattern for the SC27XX LED. For the SC27XX
11 LED controller, it only supports 4 stages to make a single
13 high time, fall time and low time for the breathing mode.
15 For the breathing mode, the SC27XX LED only expects one brightness
20 - Min stage duration: 125 ms
21 - Max stage duration: 31875 ms
/Documentation/devicetree/bindings/net/
Dmicrel.txt7 - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs.
9 Configure the LED mode with single value. The list of PHYs and the
21 See the respective PHY datasheet for the mode values.
23 - micrel,rmii-reference-clock-select-25-mhz: RMII Reference Clock Select
24 bit selects 25 MHz mode
27 than 50 MHz clock mode.
30 non-standard, inverted function of this configuration bit.
31 Specifically, a clock reference ("rmii-ref" below) is always needed to
32 actually select a mode.
34 - clocks, clock-names: contains clocks according to the common clock bindings.
[all …]
/Documentation/sound/hd-audio/
Dmodels.rst2 HD-Audio Codec-Specific Models
8 3-jack in back and a headphone out
9 3stack-digout
10 3-jack in back, a HP out and a SPDIF out
12 5-jack in back, 2-jack in front
13 5stack-digout
14 5-jack in back, 2-jack in front, a SPDIF out
16 6-jack in back, 2-jack in front
17 6stack-digout
18 6-jack with a SPDIF out
[all …]

12345