Searched +full:led +full:- +full:sources (Results 1 – 25 of 27) sorted by relevance
12
| /Documentation/devicetree/bindings/leds/ |
| D | leds-bcm6328.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/leds/leds-bcm6328.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Álvaro Fernández Rojas <noltari@gmail.com>
17 as spi-gpio. See
21 exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
24 BCM6328 LED controller has a HWDIS register, which controls whether a LED
27 is usually 1:1 for hardware to LED signals, but through the activity/link
29 explained later in brcm,link-signal-sources). Even if a LED is hardware
[all …]
|
| D | qcom,spmi-flash-led.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/qcom,spmi-flash-led.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Flash LED device inside Qualcomm Technologies, Inc. PMICs
10 - Fenglin Wu <quic_fenglinw@quicinc.com>
13 Flash LED controller is present inside some Qualcomm Technologies, Inc. PMICs.
14 The flash LED module can have different number of LED channels supported
24 - enum:
25 - qcom,pm6150l-flash-led
[all …]
|
| D | silergy,sy7802.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Silergy SY7802 1800mA Boost Charge Pump LED Driver
10 - André Apitzsch <git@apitzsch.eu>
13 The SY7802 is a current-regulated charge pump which can regulate two current
16 The SY7802 is a high-current synchronous boost converter with 2-channel
17 high side current sources. Each channel is able to deliver 900mA current.
22 - silergy,sy7802
27 enable-gpios:
[all …]
|
| D | leds-lm3697.txt | 1 * Texas Instruments - LM3697 Highly Efficient White LED Driver
3 The LM3697 11-bit LED driver provides high-
5 LED strings while delivering up to 90% efficiency.
10 - compatible:
12 - reg : I2C slave address
13 - #address-cells : 1
14 - #size-cells : 0
17 - enable-gpios : GPIO pin to enable/disable the device
18 - vled-supply : LED supply
21 - reg : 0 - LED is Controlled by bank A
[all …]
|
| D | maxim,max77693.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Krzysztof Kozlowski <krzk@kernel.org>
16 There are two LED outputs available - FLED1 and FLED2. Each of them can
17 control a separate LED or they can be connected together to double the
18 maximum current for a single connected LED. One LED is represented by one
26 const: maxim,max77693-led
28 maxim,boost-mode:
33 case both current sources are used.
[all …]
|
| D | leds-lm36274.txt | 1 * Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias
3 The LM36274 is an integrated four-channel WLED driver and LCD bias supply.
4 The backlight boost provides the power to bias four parallel LED strings with
5 up to 29V total output voltage. The 11-bit LED current is programmable via
9 Documentation/devicetree/bindings/mfd/ti-lmu.txt
12 Documentation/devicetree/bindings/regulator/lm363x-regulator.txt
15 - compatible:
16 "ti,lm36274-backlight"
17 - reg : 0
18 - #address-cells : 1
[all …]
|
| D | leds-lm3532.txt | 1 * Texas Instruments - lm3532 White LED driver with ambient light sensing
4 The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
5 programmable over an I2C-compatible interface and has independent
7 method allows for different LED currents in each current sink thus allowing
11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
16 - compatible : "ti,lm3532"
17 - reg : I2C slave address
18 - #address-cells : 1
19 - #size-cells : 0
22 - enable-gpios : gpio pin to enable (active high)/disable the device.
[all …]
|
| D | common.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jacek Anaszewski <jacek.anaszewski@gmail.com>
11 - Pavel Machek <pavel@ucw.cz>
14 LED and flash LED devices provide the same basic functionality as current
15 regulators, but extended with LED and flash LED specific features like
18 Many LED devices expose more than one current output that can be connected
19 to one or more discrete LED component. Since the arrangement of connections
20 can influence the way of the LED device initialization, the LED components
[all …]
|
| /Documentation/devicetree/bindings/mfd/ |
| D | ti-lmu.txt | 6 ------ ---------------------------------
9 LM3633 Backlight, LED and fault monitor
14 - compatible: Should be one of:
20 - reg: I2C slave address.
28 - enable-gpios: A GPIO specifier for hardware enable pin.
29 - ramp-up-us: Current ramping from one brightness level to
31 Range from 2048 us - 117.44 s
32 - ramp-down-us: Current ramping from one brightness level to
34 Range from 2048 us - 117.44 s
35 - ti,brightness-resolution - This determines whether to use 8 bit brightness
[all …]
|
| D | mediatek,mt6370.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - ChiYuan Huang <cy_huang@richtek.com>
13 MT6370 is a highly-integrated smart power management IC, which includes a
14 single cell Li-Ion/Li-Polymer switching battery charger, a USB Type-C &
15 Power Delivery (PD) controller, dual flash LED current sources, a RGB LED
26 wakeup-source: true
31 interrupt-controller: true
33 "#interrupt-cells":
[all …]
|
| D | maxim,max77693.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Chanwoo Choi <cw00.choi@samsung.com>
11 - Krzysztof Kozlowski <krzk@kernel.org>
18 includes voltage current regulators, charger, LED/flash, haptic motor driver
34 led:
37 max77693-muic:
44 const: maxim,max77693-muic
47 - compatible
[all …]
|
| D | sky81452.txt | 4 - compatible : Must be "skyworks,sky81452"
5 - reg : I2C slave address
8 - backlight : container node for backlight following the binding
9 in leds/backlight/sky81452-backlight.txt
10 - regulator : container node for regulators following the binding
11 in regulator/sky81452-regulator.txt
20 compatible = "skyworks,sky81452-backlight";
21 name = "pwm-backlight";
22 led-sources = <0 1 2 3 6>;
23 skyworks,ignore-pwm;
[all …]
|
| /Documentation/devicetree/bindings/leds/backlight/ |
| D | arcxcnn_bl.txt | 1 Binding for ArcticSand arc2c0608 LED driver
4 - compatible: should be "arc,arc2c0608"
5 - reg: slave address
8 - default-brightness: brightness value on boot, value from: 0-4095
9 - label: The name of the backlight device
11 - led-sources: List of enabled channels from 0 to 5.
14 - arc,led-config-0: setting for register ILED_CONFIG_0
15 - arc,led-config-1: setting for register ILED_CONFIG_1
16 - arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
17 - arc,comp-config: setting for register CONFIG_COMP
[all …]
|
| D | lm3630a-backlight.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/backlight/lm3630a-backlight.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI LM3630A High-Efficiency Dual-String White LED
10 - Lee Jones <lee@kernel.org>
11 - Daniel Thompson <daniel.thompson@linaro.org>
12 - Jingoo Han <jingoohan1@gmail.com>
15 The LM3630A is a current-mode boost converter which supplies the power and
26 '#address-cells':
[all …]
|
| D | ti,lm3509.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI LM3509 High Efficiency Boost for White LED's and/or OLED Displays
10 - Patrick Gansterer <paroga@paroga.com>
23 "#address-cells":
26 "#size-cells":
29 reset-gpios:
32 ti,brightness-rate-of-change-us:
36 ti,oled-mode:
[all …]
|
| D | sky81452-backlight.txt | 1 SKY81452-backlight bindings
4 - compatible : Must be "skyworks,sky81452-backlight"
7 - name : Name of backlight device. Default is 'lcd-backlight'.
8 - gpios : GPIO to use to EN pin.
10 - led-sources : List of enabled channels from 0 to 5.
12 - skyworks,ignore-pwm : Ignore both PWM input
13 - skyworks,dpwm-mode : Enable DPWM dimming mode, otherwise Analog dimming.
14 - skyworks,phase-shift : Enable phase shift mode
15 - skyworks,short-detection-threshold-volt
17 - skyworks,current-limit-mA
[all …]
|
| /Documentation/networking/device_drivers/fddi/ |
| D | skfp.rst | 1 .. SPDX-License-Identifier: GPL-2.0
6 SysKonnect driver - SKFP
9 |copy| Copyright 1998-2000 SysKonnect,
11 skfp.txt created 11-May-2000
53 - SK-5521 (SK-NET FDDI-UP)
54 - SK-5522 (SK-NET FDDI-UP DAS)
55 - SK-5541 (SK-NET FDDI-FP)
56 - SK-5543 (SK-NET FDDI-LP)
57 - SK-5544 (SK-NET FDDI-LP DAS)
58 - SK-5821 (SK-NET FDDI-UP64)
[all …]
|
| /Documentation/devicetree/bindings/net/wireless/ |
| D | mediatek,mt76.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 # Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Felix Fietkau <nbd@nbd.name>
12 - Lorenzo Bianconi <lorenzo@kernel.org>
13 - Ryder Lee <ryder.lee@mediatek.com>
25 - mediatek,mt76
26 - mediatek,mt7628-wmac
27 - mediatek,mt7622-wmac
[all …]
|
| /Documentation/admin-guide/laptops/ |
| D | asus-laptop.rst | 12 This driver provides support for extra features of ACPI-compatible ASUS laptops.
24 ------------
26 Kernel 2.6.X sources, configured for your computer, with ACPI support.
30 ------
35 - Fn key combinations
36 - Bluetooth enable and disable
37 - Wlan enable and disable
38 - GPS enable and disable
39 - Video output switching
40 - Ambient Light Sensor on and off
[all …]
|
| D | thinkpad-acpi.rst | 9 - Borislav Deianov <borislav@users.sf.net>
10 - Henrique de Moraes Holschuh <hmh@hmh.eng.br>
12 http://ibm-acpi.sf.net/
19 This driver used to be named ibm-acpi until kernel 2.6.21 and release
20 0.13-20070314. It used to be in the drivers/acpi tree, but it was
21 moved to the drivers/misc tree and renamed to thinkpad-acpi for kernel
25 The driver is named "thinkpad-acpi". In some places, like module
29 "tpacpi" is used as a shorthand where "thinkpad-acpi" would be too
33 ------
38 - Fn key combinations
[all …]
|
| /Documentation/devicetree/bindings/scsi/ |
| D | hisilicon-sas.txt | 6 - compatible : value should be as follows:
7 (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset
8 (b) "hisilicon,hip06-sas-v2" for v2 hw in hip06 chipset
9 (c) "hisilicon,hip07-sas-v2" for v2 hw in hip07 chipset
10 - sas-addr : array of 8 bytes for host SAS address
11 - reg : Contains two regions. The first is the address and length of the SAS
14 we use a CPLD for directly attached disk LED control.
15 - hisilicon,sas-syscon: phandle of syscon used for sas control
16 - ctrl-reset-reg : offset to controller reset register in ctrl reg
17 - ctrl-reset-sts-reg : offset to controller reset status register in ctrl reg
[all …]
|
| /Documentation/networking/ |
| D | 6pack.rst | 1 .. SPDX-License-Identifier: GPL-2.0
7 This is the 6pack-mini-HOWTO, written by
11 :Internet: ajk@comnets.uni-bremen.de
12 :AMPR-net: dg3kq@db0pra.ampr.org
25 - The PC is given full control over the radio
35 This kind of real-time control is especially important to supply several
39 - Each packet transferred over the serial line is supplied with a checksum,
60 db0bm.automation.fh-aachen.de. In the directory /incoming/dg3kq,
86 and the status LED are lit for about a second if the firmware initialises
99 - In the linux kernel configuration program, select the code maturity level
[all …]
|
| /Documentation/sound/hd-audio/ |
| D | realtek-pc-beep.rst | 20 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
24 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
58 +--DIV--+--!DIV--+ {1Ah boost control}
60 +--(b == 0)--+--(b != 0)--+
70 +-----!h-----+-----S-----+
79 All Realtek HDA codecs have a vendor-defined widget with node ID 20h which
92 Specifically, it selects between two sources for the input pin widget with Node
113 registers, and it's led to some fixes that improve behavior on cold boot but
122 The information here has been obtained through black-box reverse engineering of
|
| /Documentation/networking/device_drivers/ethernet/cirrus/ |
| D | cs89x0.rst | 1 .. SPDX-License-Identifier: GPL-2.0
33 2.1 CS8900-based Adapter Configuration
34 2.2 CS8920-based Adapter Configuration
46 5.2.1 Diagnostic Self-Test
66 The CS8900-based ISA Ethernet Adapters from Cirrus Logic follow
67 IEEE 802.3 standards and support half or full-duplex operation in ISA bus
69 in 16-bit ISA or EISA bus expansion slots and are available in
70 10BaseT-only or 3-media configurations (10BaseT, 10Base2, and AUI for 10Base-5
73 CS8920-based adapters are similar to the CS8900-based adapter with additional
85 or loaded at run-time as a device driver module.
[all …]
|
| /Documentation/scsi/ |
| D | sym53c8xx_2.rst | 1 .. SPDX-License-Identifier: GPL-2.0
4 SYM-2 driver
11 95170 DEUIL LA BARRE - FRANCE
15 2004-10-09
43 10.2.3 LED support
67 This driver supports the whole SYM53C8XX family of PCI-SCSI controllers.
68 It also support the subset of LSI53C10XX PCI-SCSI controllers that are based
72 with the FreeBSD SYM-2 driver. The 'glue' that allows this driver to work
81 - Wolfgang Stanglmeier <wolf@cologne.de>
82 - Stefan Esser <se@mi.Uni-Koeln.de>
[all …]
|
12