Searched full:loopback (Results 1 – 25 of 52) sorted by relevance
123
| /Documentation/sound/hd-audio/ |
| D | controls.rst | 38 Analog Loopback
39 This control enables/disables the analog-loopback circuit. This
40 appears only when "loopback" is set to true in a codec hint
41 (see HD-Audio.txt). Note that on some codecs the analog-loopback
77 Loopback Mixing
78 An enum control to determine whether the analog-loopback route is
79 enabled or not. When it's enabled, the analog-loopback is mixed to
|
| D | realtek-pc-beep.rst | 33 Amplify 1Ah loopback, left (L): 1 bit
37 Amplify 1Ah loopback, right (R): 1 bit
41 Loopback 1Ah to 21h [active low] (h): 1 bit
46 Loopback 1Ah to 14h (S): 1 bit
64 Loopback of 1Ah to 21h/14h::
115 away from PC Beep but have failed to disable both loopback paths. On my
|
| /Documentation/ABI/testing/ |
| D | configfs-usb-gadget-loopback | 1 What: /config/usb-gadget/gadget/functions/Loopback.name
8 qlen depth of loopback queue
|
| D | sysfs-block-loop | 7 "0"). Autoclear (if set) indicates that the loopback device will
|
| /Documentation/filesystems/ |
| D | bfs.rst | 15 BFS filesystem via loopback::
30 this will allocate the first available loopback device (and load loop.o
31 kernel module if necessary) automatically. If the loopback driver is not
|
| D | adfs.rst | 24 This is intended to support loopback mounted Linux native filesystems
|
| /Documentation/sound/designs/ |
| D | control-names.rst | 78 Loopback
79 Analog Loopback D/A -> A/D loopback
80 Digital Loopback playback -> capture loopback -
|
| D | powersave.rst | 11 the device and/or no analog loopback is set, the power disablement is
|
| /Documentation/devicetree/bindings/serial/ |
| D | 8250.yaml | 165 no-loopback-test:
168 Set to indicate that the port does not implement loopback test mode.
259 no-loopback-test;
|
| /Documentation/networking/ |
| D | can.rst | 142 Local Loopback of Sent Frames
160 some kind of local loopback of the sent CAN frames on the appropriate
167 reflect the correct [#f1]_ traffic on the node the loopback of the sent
169 the CAN network interface is not capable of performing the loopback for
173 The loopback functionality is enabled by default to reflect standard
175 the RT-SocketCAN group the loopback optionally may be disabled for each
477 - The loopback of sent CAN frames is enabled (see :ref:`socketcan-local-loopback2`)
478 - The socket does not receive its own sent frames (in loopback mode)
599 To meet multi user needs the local loopback is enabled by default
601 (e.g. when only one application uses the CAN bus) this loopback
[all …]
|
| D | ipv6.rst | 54 Only the IPv6 loopback address (::1) and link-local addresses
|
| D | generic-hdlc.rst | 68 loopback
69 - activate hardware loopback (for testing only)
|
| D | msg_zerocopy.rst | 238 Loopback section in Implementation
257 Be cognizant of the loopback constraint. The test can be run between
261 loopback restriction can be temporarily relaxed by making
|
| D | devmem.rst | 247 - Loopback is not functional. Loopback relies on copying the payload, which is
|
| /Documentation/devicetree/bindings/soc/fsl/cpm_qe/ |
| D | fsl,ucc-hdlc.yaml | 98 fsl,tdm-internal-loopback:
102 Internal loopback connecting on TDM layer.
|
| /Documentation/networking/device_drivers/ethernet/aquantia/ |
| D | atlantic.rst | 400 DMASystemLoopback: DMA Host loopback.
401 PKTSystemLoopback: Packet buffer host loopback.
402 DMANetworkLoopback: Network side loopback on DMA block.
403 PHYInternalLoopback: Internal loopback on Phy.
404 PHYExternalLoopback: External loopback on Phy (with loopback ethernet cable).
|
| /Documentation/networking/device_drivers/ethernet/marvell/ |
| D | octeontx2.rst | 35 - Loopback interface (LBK)
117 SR-IOV PF and the VFs which work in pairs using internal HW loopback channels (LBK).
129 - RVU PF0 ie admin function creates these VFs and maps them to loopback block's channels.
134 for loopback VFs.
|
| /Documentation/admin-guide/media/ |
| D | cx88.rst | 21 - audio data dma (i.e. recording without loopback cable to the
|
| /Documentation/networking/devlink/ |
| D | ice.rst | 80 - Controls loopback behavior by tuning scheduler bandwidth.
85 ``enabled`` - loopback traffic is allowed on port
87 ``disabled`` - loopback traffic is not allowed on this port
89 ``prioritized`` - loopback traffic is prioritized on this port
92 ``prioritized`` provides ability to adjust loopback traffic rate to increase
|
| /Documentation/devicetree/bindings/phy/ |
| D | microchip,sparx5-serdes.yaml | 25 * Multiple loopback modes
|
| /Documentation/devicetree/bindings/net/ |
| D | marvell,pp2.yaml | 122 marvell,loopback:
124 description: port is loopback mode.
|
| /Documentation/devicetree/bindings/soc/ti/ |
| D | keystone-navigator-dma.txt | 57 - ti,loop-back: To loopback Tx streaming I/F to Rx streaming I/F. Used for
|
| /Documentation/admin-guide/ |
| D | initrd.rst | 129 - a loopback device (the most elegant solution)
131 We'll describe the loopback device method:
133 1) make sure loopback block devices are configured into the kernel
|
| /Documentation/sound/cards/ |
| D | mixart.rst | 61 Loopback from 'pcm0c' to 'pcm0p' with digital volume
|
| /Documentation/sound/ |
| D | utimers.rst | 101 sound loopback. For instance, if one of the applications receives sound
|
123