Searched full:microseconds (Results 1 – 25 of 128) sorted by relevance
123456
| /Documentation/tools/rtla/ |
| D | common_osnoise_options.rst | 8 Set the *osnoise* tracer period in microseconds.
12 Set the *osnoise* tracer runtime in microseconds.
16 Stop the trace if a single sample is higher than the argument in microseconds.
21 Stop the trace if the total sample is higher than the argument in microseconds.
|
| /Documentation/userspace-api/media/rc/ |
| D | lirc-get-rec-resolution.rst | 13 LIRC_GET_REC_RESOLUTION - Obtain the value of receive resolution, in microseconds.
20 ``int ioctl(int fd, LIRC_GET_REC_RESOLUTION, __u32 *microseconds)``
28 ``microseconds``
29 Resolution, in microseconds.
|
| D | lirc-dev-intro.rst | 106 Signifies the presence of IR in microseconds, also known as *flash*.
110 Signifies absence of IR in microseconds, also known as *gap*.
122 of microseconds with no IR.
138 The values are alternating pulse and space lengths, in microseconds. The
|
| /Documentation/ABI/testing/ |
| D | sysfs-module | 22 microframe to be 80%, that is 100 microseconds out of 125
23 microseconds (full microframe).
27 microseconds of isochronous bandwidth per microframe to work
32 microseconds of periodic bandwidth per microframe.
|
| D | debugfs-hyperv | 14 microseconds (inclusive).
21 Description: Fuzz testing message delay value between 0 - 1000 microseconds
|
| D | sysfs-class-led-flash | 26 Hardware timeout for flash, in microseconds. The flash strobe
36 Maximum flash timeout for this LED, in microseconds.
|
| D | sysfs-class-rc-nuvoton | 8 All values are in microseconds.
|
| /Documentation/devicetree/bindings/net/ |
| D | mdio.yaml | 38 RESET pulse width in microseconds. It applies to all MDIO devices
44 Delay after reset deassert in microseconds. It applies to all MDIO
86 Delay after the reset was asserted in microseconds. If this
91 Delay after the reset was deasserted in microseconds. If
|
| /Documentation/devicetree/bindings/power/ |
| D | domain-idle-state.yaml | 33 The worst case latency in microseconds required to enter the idle
39 The worst case latency in microseconds required to exit the idle
44 The minimum residency duration in microseconds after which the idle
|
| /Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 91 -maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds
95 -maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds
111 Here supported time periods by device in microseconds are as follows:
112 MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds.
113 MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
114 MAX77663 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
|
| /Documentation/userspace-api/media/v4l/ |
| D | metafmt-d4xx.rst | 59 - Exposure time (in microseconds) used to capture the frame
97 - Time in microseconds from the beginning of a frame till its middle
99 - Time, used to read out a frame in microseconds
101 - Frame exposure time in microseconds
103 - In microseconds = 1000000 / framerate
105 - Time in microseconds from start of frame to data in USB buffer
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-arb-gpio-challenge.yaml | 42 microseconds).
78 We'll give up after this many microseconds.
83 We'll attempt another claim after this many microseconds.
|
| /Documentation/devicetree/bindings/input/ |
| D | qcom,pm8921-keypad.yaml | 41 Time in microseconds that key must be pressed or
47 description: time in microseconds to pause between successive scans of the
|
| D | qcom,pm8941-pwrkey.yaml | 29 Time in microseconds that key must be pressed or
|
| D | qcom,pm8921-pwrkey.yaml | 36 Time in microseconds that key must be pressed or
|
| /Documentation/ABI/stable/ |
| D | sysfs-bus-w1 | 4 Description: Bus scanning interval, microseconds component.
|
| /Documentation/admin-guide/mm/damon/ |
| D | reclaim.rst | 77 Time threshold for cold memory regions identification in microseconds.
123 Desired level of memory pressure-stall time in microseconds.
127 memory pressure is incurred. System-wide ``some`` memory PSI in microseconds
184 Sampling interval for the monitoring in microseconds.
192 Aggregation interval for the monitoring in microseconds.
|
| D | lru_sort.rst | 94 Time threshold for cold memory regions identification in microseconds.
127 The watermarks check time interval in microseconds.
162 Sampling interval for the monitoring in microseconds.
170 Aggregation interval for the monitoring in microseconds.
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | atmel,sama9260-adc.yaml | 43 Startup Time of the ADC in microseconds as defined in the datasheet
68 description: Sample and Hold Time in microseconds
|
| /Documentation/scheduler/ |
| D | sched-bwc.rst | 13 each given "period" (microseconds), a task group is allocated up to "quota"
14 microseconds of CPU time. That quota is assigned to per-cpu run queues in
77 - cpu.cfs_quota_us: run-time replenished within a period (in microseconds)
78 - cpu.cfs_period_us: the length of a period (in microseconds)
80 - cpu.cfs_burst_us: the maximum accumulated run-time (in microseconds)
|
| /Documentation/devicetree/bindings/rng/ |
| D | timeriomem_rng.yaml | 18 description: wait time in microseconds to use between samples
|
| /Documentation/devicetree/bindings/regulator/ |
| D | fixed-regulator.yaml | 90 description: startup time in microseconds
93 description: off delay time in microseconds
|
| D | regulator.yaml | 65 description: The time taken, in microseconds, for the supply rail to
74 description: Settling time, in microseconds, for voltage change if regulator
79 description: Settling time, in microseconds, for voltage increase if
85 description: Settling time, in microseconds, for voltage decrease if
|
| /Documentation/devicetree/bindings/spi/ |
| D | spi-peripheral-props.yaml | 72 Delay, in microseconds, after a read transfer.
89 Delay, in microseconds, after a write transfer.
|
| /Documentation/devicetree/bindings/sound/ |
| D | ti,tas5086.txt | 14 - ti,charge-period: This property should contain the time in microseconds
|
123456