Home
last modified time | relevance | path

Searched +full:num +full:- +full:tx +full:- +full:queues (Results 1 – 8 of 8) sorted by relevance

/Documentation/devicetree/bindings/mailbox/
Dti,omap-mailbox.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mailbox/ti,omap-mailbox.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Suman Anna <s-anna@ti.com>
19 Each mailbox IP block/cluster has a certain number of h/w fifo queues and
26 interrupt configuration registers, and have a rx and tx interrupt source per
28 appropriate programming of the rx and tx interrupt sources on the appropriate
31 The number of h/w fifo queues and interrupt lines dictate the usable
34 h/w fifo queues and interrupt lines between different instances. The interrupt
[all …]
/Documentation/devicetree/bindings/net/
Dbrcm,systemport.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Florian Fainelli <f.fainelli@gmail.com>
15 - brcm,systemport-v1.00
16 - brcm,systemportlite-v1.00
17 - brcm,systemport
25 - description: interrupt line for RX queues
26 - description: interrupt line for TX queues
27 - description: interrupt line for Wake-on-LAN
[all …]
Dfsl,fec.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Shawn Guo <shawnguo@kernel.org>
11 - Wei Fang <wei.fang@nxp.com>
12 - NXP Linux Team <linux-imx@nxp.com>
15 - $ref: ethernet-controller.yaml#
20 - enum:
21 - fsl,imx25-fec
22 - fsl,imx27-fec
[all …]
/Documentation/netlink/specs/
Drt_link.yaml1 # SPDX-License-Identifier: ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)
3 name: rt-link
4 protocol: netlink-raw
11 -
12 name: ifinfo-flags
15 -
17 -
19 -
21 -
23 -
[all …]
/Documentation/networking/device_drivers/ethernet/ti/
Dcpsw.rst1 .. SPDX-License-Identifier: GPL-2.0
26 - TX queues must be rated starting from txq0 that has highest priority
27 - Traffic classes are used starting from 0, that has highest priority
28 - CBS shapers should be used with rated queues
29 - The bandwidth for CBS shapers has to be set a little bit more then
30 potential incoming rate, thus, rate of all incoming tx queues has
32 - Real rates can differ, due to discreetness
33 - Map skb-priority to txq is not enough, also skb-priority to l2 prio
35 - Any l2/socket prio (0 - 7) for classes can be used, but for
37 - only 2 classes tested: A and B, but checked and can work with more,
[all …]
/Documentation/networking/device_drivers/ethernet/intel/
Di40e.rst1 .. SPDX-License-Identifier: GPL-2.0+
8 Copyright(c) 1999-2018 Intel Corporation.
13 - Overview
14 - Identifying Your Adapter
15 - Intel(R) Ethernet Flow Director
16 - Additional Configurations
17 - Known Issues
18 - Support
47 ----------------------
49 …intel.com/content/dam/www/public/us/en/documents/release-notes/xl710-ethernet-controller-feature-m…
[all …]
Diavf.rst1 .. SPDX-License-Identifier: GPL-2.0+
8 Copyright(c) 2013-2018 Intel Corporation.
13 - Overview
14 - Identifying Your Adapter
15 - Additional Configurations
16 - Known Issues/Troubleshooting
17 - Support
30 The guest OS loading the iavf driver must support MSI-X interrupts.
53 ---------------------
58 # dmesg -n 8
[all …]
/Documentation/admin-guide/
Dkernel-parameters.txt16 force -- enable ACPI if default was off
17 on -- enable ACPI but allow fallback to DT [arm64,riscv64]
18 off -- disable ACPI if default was on
19 noirq -- do not use ACPI for IRQ routing
20 strict -- Be less tolerant of platforms that are not
22 rsdt -- prefer RSDT over (default) XSDT
23 copy_dsdt -- copy DSDT to memory
24 nospcr -- disable console in ACPI SPCR table as
41 If set to vendor, prefer vendor-specific driver
73 Documentation/firmware-guide/acpi/debug.rst for more information about
[all …]