Searched full:oob (Results 1 – 12 of 12) sorted by relevance
| /Documentation/devicetree/bindings/mtd/ |
| D | davinci-nand.txt | 52 - nand-on-flash-bbt: use flash based bad block table support. OOB
53 identifier is saved in OOB area. If not present
66 - ti,davinci-nand-use-bbt: use flash based bad block table support. OOB
67 identifier is saved in OOB area. If not present
|
| D | raw-nand-chip.yaml | 37 but can be explicitly set to "oob", if all ECC bytes are
38 known to be stored in the OOB area, or "interleaved" if ECC
41 enum: [ oob, interleaved ]
75 providing the best strength and taking the OOB area size
|
| D | brcm,brcmnand.yaml | 134 brcm,nand-oob-sector-size:
143 and OOB size) in many cases, but when booting
220 brcm,nand-oob-sector-size: false
|
| D | gpmi-nand.yaml | 76 Don't swap the bad block marker from the OOB area with the byte in
|
| /Documentation/devicetree/bindings/ata/ |
| D | nvidia,tegra-ahci.yaml | 34 - const: sata-oob
44 - const: sata-oob
170 clock-names = "sata", "sata-oob";
174 reset-names = "sata", "sata-cold", "sata-oob";
|
| D | ceva,ahci-1v84.yaml | 44 OOB timing value for COMINIT parameter for port 0.
56 OOB timing value for COMWAKE parameter for port 0.
90 OOB timing value for COMINIT parameter for port 1.
102 OOB timing value for COMWAKE parameter for port 1.
|
| /Documentation/scsi/ |
| D | libsas.rst | 11 phy/OOB/link management, the SAS layer is concerned with:
25 phy/OOB management, and vendor specific tasks and generates
40 start OOB (at which point your driver will start calling the
84 - you set this when OOB has finished and then notify
236 *but* before you enable the phys to do OOB::
337 - OOB went fine and oob_mode is valid
340 - Error while doing OOB, the device probably
|
| /Documentation/driver-api/mei/ |
| D | iamt.rst | 10 Intel AMT provides the ability to manage a host remotely out-of-band (OOB)
25 Intel AMT (OOB) communication is based on SOAP (deprecated
|
| /Documentation/devicetree/bindings/net/wireless/ |
| D | brcm,bcm4329-fmac.yaml | 63 description: Out-of-band (OOB) IRQ line for waking up the host
68 description: Name for the OOB IRQ, this must be set to "host-wake".
|
| /Documentation/admin-guide/pm/ |
| D | intel-speed-select.rst | 268 It is possible to change SST-PP level using out of band (OOB) agent (Via some
277 a command line option --oob::
279 # intel-speed-select --oob
282 OOB mode is enabled and will run as daemon
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-mtd | 90 Number of OOB bytes per page.
|
| /Documentation/driver-api/ |
| D | mtdnand.rst | 421 remaining free bytes in the oob area are managed by the autoplacement
422 code. Provide a matching oob-layout in this case. See rts_from4.c and
|