Searched full:operational (Results 1 – 25 of 72) sorted by relevance
123
| /Documentation/networking/ |
| D | operstates.rst | 4 Operational States
11 Linux distinguishes between administrative and operational state of an
19 to be performed before user data can be transferred. Operational state
23 influence operational state. To accommodate this, operational state is
32 Both admin and operational state can be queried via the netlink
43 Interface is in RFC2863 operational state UP or UNKNOWN. This is for
60 operational state. Interface must be considered for user data as
61 setting operational state has not been implemented in every driver.
85 Interface is operational up and can be used.
154 RFC2863 operational state of an interface. Setting IFLA_LINKMODE to 1
|
| D | multiqueue.rst | 24 device is still operational. netdev->queue_lock is still used when the device
|
| /Documentation/misc-devices/ |
| D | tps6594-pfsm.rst | 16 manages operational modes. Depending on the current operational mode,
54 One of the operational modes.
60 One of the operational modes.
64 One of the operational modes.
|
| D | apds990x.rst | 44 Driver controls chip operational state using pm_runtime framework.
45 Voltage regulators are controlled based on chip operational state.
|
| D | isl29003.rst | 27 The driver allows to set the lux range, the bit resolution, the operational
|
| /Documentation/devicetree/bindings/soc/fsl/cpm_qe/ |
| D | fsl,cpm1-scc-qmc.yaml | 76 fsl,operational-mode:
81 The channel operational mode
167 fsl,operational-mode = "transparent";
176 fsl,operational-mode = "transparent";
188 fsl,operational-mode = "hdlc";
|
| D | fsl,qe-ucc-qmc.yaml | 88 fsl,operational-mode:
93 The channel operational mode
171 fsl,operational-mode = "transparent";
180 fsl,operational-mode = "transparent";
192 fsl,operational-mode = "hdlc";
|
| /Documentation/devicetree/bindings/display/samsung/ |
| D | samsung,exynos-hdmi.yaml | 122 respectively if HDMI-PHY is off and operational.
125 respectively if HDMI-PHY is off and operational.
127 clocks in case HDMI-PHY is not operational.
|
| /Documentation/devicetree/bindings/net/ |
| D | ti,dp83869.yaml | 64 Operational mode for the PHY. If this is not set then the operational
|
| /Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd71815-regulator.yaml | 92 # Bucks 1 and 2 support giving separate voltages for operational states
93 # (RUN /CLEAN according to data-sheet) and non operational states
|
| /Documentation/arch/s390/ |
| D | driver-model.rst | 30 if they are displaced by another ccw device becoming operational on their
32 if they become operational again on that subchannel.
64 The path installed, path available and path operational masks.
199 * In disconnected state, device operational again (CIO_OPER). The
|
| D | vfio-ccw.rst | 236 The channel path(s) used for the I/O were found to be not operational.
239 The device was found to be not operational.
270 The device was found to be not operational.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | tps6105x.txt | 12 This subnode selects the chip's operational mode.
|
| /Documentation/devicetree/bindings/thermal/ |
| D | samsung,exynos-thermal.yaml | 89 Operational clock for TMU channel.
112 Operational clock for TMU channel.
|
| /Documentation/devicetree/bindings/pci/ |
| D | ralink,rt3883-pci.txt | 23 - status: indicates the operational status of the device.
96 - status: indicates the operational status of the sub-node.
|
| D | renesas,pci-rcar-gen2.yaml | 39 - description: Operational registers for the OHCI/EHCI controllers.
|
| /Documentation/arch/arm/sunxi/ |
| D | clocks.rst | 16 While the system is operational, you would see something like::
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-usb_power_delivery | 144 Operational current of the sink in milliamperes.
189 The operational current in milliamperes that the sink requires
222 The operational power that the sink requires at the given
|
| D | sysfs-bus-siox | 77 be operational. "1" means the watchdog keeps the device in reset.
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | gmt,g762.yaml | 22 Additional information on operational parameters for the device is available
|
| /Documentation/scsi/ |
| D | scsi_fc_transport.rst | 239 The vport is not operational as the physical link is not operational.
250 The vport is not operational. One of the following conditions were
258 The vport is not operational. The Fabric failed FDISC with a status
263 The vport is not operational. The Fabric has LOGO'd the N_Port_ID
267 The vport is not operational. The Fabric failed FDISC with a status
271 The vport is not operational. This is a catchall for all other
|
| /Documentation/ABI/stable/ |
| D | sysfs-transport-srp | 52 remote port. "running" if the transport layer is operational;
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | qcom,pdc.yaml | 17 well detect interrupts when the GIC is non-operational.
|
| D | qcom,mpm.yaml | 18 after GIC becomes operational.
|
| /Documentation/w1/masters/ |
| D | ds2490.rst | 20 low-level operational chip.
|
123