Searched full:pairs (Results 1 – 25 of 173) sorted by relevance
1234567
| /Documentation/locking/ |
| D | locktorture.rst | 53 spin_lock() and spin_unlock() pairs.
56 spin_lock_irq() and spin_unlock_irq() pairs.
59 read/write lock() and unlock() rwlock pairs.
63 rwlock pairs.
66 mutex_lock() and mutex_unlock() pairs.
69 rtmutex_lock() and rtmutex_unlock() pairs.
73 read/write down() and up() semaphore pairs.
|
| /Documentation/devicetree/bindings/usb/ |
| D | hisilicon,histb-xhci.txt | 9 - clocks: a list of phandle + clock-specifier pairs, one for each
16 - resets: a list of phandle and reset specifier pairs as listed in
20 - phys: a list of phandle + phy specifier pairs
|
| D | ehci-st.txt | 17 - resets : phandle + reset specifier pairs to the powerdown and softreset lines
|
| /Documentation/ABI/testing/ |
| D | sysfs-uevent | 18 You need to pass UUID first before any KEY=VALUE pairs.
31 The KEY=VALUE pairs can contain alphanumeric characters only.
33 It's possible to define zero or more pairs - each pair is then
|
| D | sysfs-bus-event_source-devices-format | 10 name/value pairs.
|
| D | sysfs-driver-qat_rl | 41 (RW) When read, reports the current assigned ring pairs for the
43 When wrote to, configures the ring pairs associated to a new SLA.
49 Selected ring pairs must to be assigned to a single service,
54 The maximum number of ring pairs is 4 per SLA.
|
| /Documentation/networking/pse-pd/ |
| D | pse-pi.rst | 20 systems that utilize two pairs for power delivery.
22 deliver power over all four pairs of an Ethernet cable.
31 two pairs of wires, SPE operates on a simpler model due to its single-pair
50 networks 10/100BaseT or 1G/2G/5G/10GBaseT, the pairs used are carrying data.
56 10/100BaseT network the pairs used are spare pairs without data and are less
98 and the 1000/2.5G/5G/10GBaseT in the PSE 2 pairs connection.
112 - "Direct" indicate a variant where the power is injected directly to pairs
113 without using magnetics in case of spare pairs.
117 In case of PSE 4 pairs, a PSE supporting only 10/100BaseT (which mean Direct
118 Power on pinout Alternative B) is not compatible with a 4 pairs
[all …]
|
| /Documentation/devicetree/bindings/sound/ |
| D | sirf-audio-port.txt | 6 - dmas: List of DMA controller phandle and DMA request line ordered pairs.
8 These strings correspond 1:1 with the ordered pairs in dmas.
|
| D | brcm,bcm2835-i2s.txt | 7 - dmas: List of DMA controller phandle and DMA request line ordered pairs.
9 These strings correspond 1:1 with the ordered pairs in dmas.
|
| D | sprd-pcm.txt | 5 - dmas: Specify the list of DMA controller phandle and DMA request line ordered pairs.
7 These strings correspond 1:1 with the ordered pairs in dmas.
|
| D | adi,axi-spdif-tx.txt | 6 - clocks : Pairs of phandle and specifier referencing the controller's clocks.
11 - dmas: Pairs of phandle and specifier for the DMA channel that is used by
|
| D | adi,axi-i2s.txt | 9 - clocks : Pairs of phandle and specifier referencing the controller's clocks.
14 - dmas: Pairs of phandle and specifier for the DMA channels that are used by
|
| D | nvidia,tegra210-admaif.yaml | 12 ADMAIF channel. ADMA channel sending data to AHUB pairs with ADMAIF
13 Tx channel and ADMA channel receiving data from AHUB pairs with
|
| /Documentation/devicetree/bindings/display/hisilicon/ |
| D | hisi-ade.txt | 13 - clocks: a list of phandle + clock-specifier pairs, one for each entry
21 phandle + clock-specifier pairs.
|
| /Documentation/devicetree/bindings/interconnect/ |
| D | interconnect.txt | 46 interconnects : Pairs of phandles and interconnect provider specifier to denote
57 specifier pairs.
|
| /Documentation/devicetree/bindings/pci/ |
| D | hisilicon-histb-pcie.txt | 21 - clocks: List of phandle and clock specifier pairs as listed in clock-names
28 - resets: List of phandle and reset specifier pairs as listed in reset-names
|
| /Documentation/admin-guide/ |
| D | bootconfig.rst | 233 passing the kernel parameters. All the key-value pairs under ``kernel``
235 pairs under ``init`` will be passed to init process via the cmdline.
272 up to 512 key-value pairs. If keys contains 3 words in average, it can
273 contain 256 key-value pairs. In most cases, the number of config items
285 User can query or loop on key-value pairs, also it is possible to find
290 config, you can use xbc_for_each_key_value() to iterate key-value pairs.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | omap-usb-tll.txt | 12 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
|
| /Documentation/devicetree/bindings/powerpc/ |
| D | ibm,vas.txt | 10 - reg : Should contain 4 pairs of 64-bit fields specifying the Hypervisor
|
| /Documentation/devicetree/bindings/reset/ |
| D | snps,hsdk-reset.txt | 9 - reg: should always contain 2 pairs address - length: first for reset
|
| /Documentation/devicetree/bindings/display/ |
| D | snps,arcpgu.txt | 10 - clocks: A list of phandle + clock-specifier pairs, one for each
|
| /Documentation/devicetree/bindings/ata/ |
| D | ahci-dm816.txt | 9 - clocks: list of phandle and clock specifier pairs (or only
|
| /Documentation/devicetree/bindings/mmc/ |
| D | sdhci-milbeaut.txt | 9 list of phandles and clock-specifier pairs.
|
| /Documentation/devicetree/bindings/clock/ |
| D | snps,pll-clock.txt | 11 - reg: should always contain 2 pairs address - length: first for PLL config
|
| /Documentation/devicetree/bindings/opp/ |
| D | opp-v1.yaml | 19 This binding only supports voltage-frequency pairs.
|
1234567