Searched full:passive (Results 1 – 25 of 58) sorted by relevance
123
| /Documentation/devicetree/bindings/fpga/ |
| D | altera-passive-serial.txt | 1 Altera Passive Serial SPI FPGA Manager
4 referred to as "passive serial".
5 The passive serial link is not technically SPI, and might require extra
12 "altr,fpga-passive-serial",
13 "altr,fpga-arria10-passive-serial"
23 compatible = "altr,fpga-passive-serial";
|
| /Documentation/devicetree/bindings/thermal/ |
| D | brcm,sr-thermal.txt | 34 polling-delay-passive = <0>;
46 polling-delay-passive = <0>;
58 polling-delay-passive = <0>;
70 polling-delay-passive = <0>;
82 polling-delay-passive = <0>;
94 polling-delay-passive = <0>;
|
| D | thermal-zones.yaml | 29 1. when passive cooling is activated (polling-delay-passive)
72 polling-delay-passive:
76 checking this thermal zone while doing passive cooling. Setting
160 - passive # enable passive cooling e.g. throttling cpu
164 There are four valid trip types: active, passive, hot,
177 The passive trip type can be used to slow down HW e.g. run
279 polling-delay-passive = <250>;
288 type = "passive";
294 type = "passive";
324 polling-delay-passive = <250>;
[all …]
|
| D | thermal-cooling-devices.yaml | 28 - Passive cooling: by means of regulating device performance. A typical
29 passive cooling mechanism is a CPU that has dynamic voltage and frequency
98 polling-delay-passive = <250>;
107 type = "passive";
|
| D | thermal-idle.yaml | 106 polling-delay-passive = <100>;
115 type = "passive";
121 type = "passive";
127 type = "passive";
|
| D | st,stm32-thermal.yaml | 58 polling-delay-passive = <0>;
66 type = "passive";
|
| D | qcom,spmi-temp-alarm.yaml | 66 polling-delay-passive = <100>;
74 type = "passive";
|
| D | amazon,al-thermal.txt | 20 polling-delay-passive = <250>;
|
| D | mediatek,lvts-thermal.yaml | 131 polling-delay-passive = <250>;
138 type = "passive";
|
| D | dlg,da9062-thermal.yaml | 27 polling-delay-passive:
|
| D | brcm,ns-thermal.yaml | 44 polling-delay-passive = <0>;
|
| D | ti,am654-thermal.yaml | 45 polling-delay-passive = <250>; /* milliseconds */
|
| D | db8500-thermal.txt | 12 - tripN-type : type of trip point N, should be one of "active" "passive" "hot"
|
| /Documentation/devicetree/bindings/interconnect/ |
| D | samsung,exynos-bus.yaml | 28 - passive bus device
30 Basically, parent and passive bus device share the same power line. The
32 rest bus devices (passive bus device) depend on the decision of the parent
35 on the parent device as passive device.
38 |--- B block (passive)
39 |--- C block (passive)
81 |Mode |*parent|passive |passive|passive|passive|| |
175 Parent bus device. Valid and required only for the passive bus devices.
|
| /Documentation/admin-guide/pm/ |
| D | intel_pstate.rst | 57 ``intel_pstate`` can operate in two different modes, active or passive. In the
59 allows the hardware to do performance scaling by itself, while in the passive
195 Passive Mode
200 ``intel_pstate=passive`` argument is passed to the kernel in the command line
202 ``intel_pstate=no_hwp`` setting causes the driver to start in the passive mode
222 the so-called "turbo" frequency ranges). In other words, in the passive mode
290 ``CPUFreq`` core and (in the passive mode) to generic scaling governors. This
414 Operation mode of the driver: "active", "passive" or "off".
420 "passive"
421 The driver is functional and in the `passive mode
[all …]
|
| /Documentation/fb/ |
| D | pxafb.rst | 10 modprobe pxafb options=vmem:2M,mode:640x480-8,passive
14 video=pxafb:vmem:2M,mode:640x480-8,passive
53 active | passive => LCCR0_PAS
55 Active (TFT) or Passive (STN) display
59 Single or dual panel passive display
|
| D | sa1100fb.rst | 14 For most common passive displays, giving the option::
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | pwm-fan.yaml | 67 polling-delay-passive = <0>;
74 type = "passive";
|
| /Documentation/isdn/ |
| D | m_isdn.rst | 6 the old I4L driver architecture for passive ISDN cards.
|
| /Documentation/devicetree/bindings/pwm/ |
| D | atmel,hlcdc-pwm.yaml | 18 converted to an analog voltage with a simple passive filter. LCD display
|
| /Documentation/driver-api/thermal/ |
| D | power_allocator.rst | 8 The governor works optimally with the following two passive trip points:
11 control loop starts operating. This is the first passive trip
16 is controlling for. This is the last passive trip point of the
84 polling-delay-passive = <100>;
|
| D | sysfs-api.rst | 88 number of milliseconds to wait between polls when performing passive
349 passive, active. If an ACPI thermal zone supports critical, passive,
369 |---trip_point_1_type: passive
375 |---cdev0_trip_point: 1 /* cdev0 can be used for passive */
|
| /Documentation/devicetree/bindings/display/ |
| D | repaper.txt | 33 polling-delay-passive = <0>;
|
| /Documentation/devicetree/bindings/regulator/ |
| D | dlg,da9121.yaml | 77 dlg,irq-polling-delay-passive-ms:
154 dlg,irq-polling-delay-passive-ms = <2000>;
185 dlg,irq-polling-delay-passive-ms = <2000>;
|
| /Documentation/devicetree/bindings/usb/ |
| D | ite,it5205.yaml | 7 title: ITE IT5202 Type-C USB Alternate Mode Passive MUX
|
123