Searched full:pause (Results 1 – 25 of 75) sorted by relevance
123
| /Documentation/devicetree/bindings/net/ |
| D | ethernet-controller.yaml | 187 Pause configuration. 0 for no pause, 1 for pause
191 Asymmetric pause configuration. 0 for no asymmetric
192 pause, 1 for asymmetric pause
208 pause:
211 Indicates that pause should be enabled.
213 asym-pause:
|
| D | brcm,bcm7445-switch-v4.0.txt | 33 brcm,fcb-pause-override;
|
| D | nixge.txt | 81 pause;
|
| /Documentation/leds/ |
| D | leds-qcom-lpg.rst | 55 in the pattern, the so called "low pause" and "high pause".
57 Low-pause pattern::
75 driver when the given pattern is a palindrome. In this case the "high pause"
|
| /Documentation/input/ |
| D | uinput.rst | 87 * device. We are inserting a pause here so that userspace has time
90 * to send. This pause is only needed in our example code!
150 * device. We are inserting a pause here so that userspace has time
153 * to send. This pause is only needed in our example code!
221 * device. We are inserting a pause here so that userspace has time
224 * to send. This pause is only needed in our example code!
|
| /Documentation/devicetree/bindings/mips/cavium/ |
| D | bootbus.txt | 44 - cavium,t-pause: A cell specifying the PAUSE timing (in nS).
94 cavium,t-pause = <0>;
114 cavium,t-pause = <0>;
|
| /Documentation/devicetree/bindings/net/dsa/ |
| D | brcm,sf2.yaml | 69 brcm,fcb-pause-override:
71 Block pause override capability
155 brcm,fcb-pause-override;
|
| D | mscc,ocelot.yaml | 146 pause;
158 pause;
243 pause;
255 pause;
|
| D | mediatek,mt7530.yaml | 358 pause;
421 pause;
485 pause;
551 pause;
639 pause;
727 pause;
814 pause;
|
| D | vitesse,vsc73xx.yaml | 144 pause;
189 pause;
|
| /Documentation/driver-api/ |
| D | slimbus.rst | 103 Clock-pause:
105 SLIMbus mandates that a reconfiguration sequence (known as clock-pause) be
109 Clock-pause is exited by waking up framer device (if controller driver initiates
113 Clock-pause APIs:
|
| /Documentation/netlink/specs/ |
| D | ethtool.yaml | 567 name: pause-stat
579 name: pause
597 nested-attributes: pause-stat
1507 name: pause-get
1508 doc: Get pause params.
1510 attribute-set: pause
1512 do: &pause-get-op
1517 attributes: &pause
1524 dump: *pause-get-op
1526 name: pause-set
[all …]
|
| /Documentation/devicetree/bindings/input/ |
| D | qcom,pm8921-keypad.yaml | 47 description: time in microseconds to pause between successive scans of the
52 description: time in nanoseconds to pause between scans of each row in the
|
| /Documentation/userspace-api/media/rc/ |
| D | rc-tables.rst | 192 - Pause stream
194 - PAUSE / FREEZE
208 - Alternate between play and pause
210 - PLAY / PAUSE
226 - CAPTURE / REC / RECORD/PAUSE
|
| /Documentation/networking/device_drivers/ethernet/mellanox/mlx5/ |
| D | counters.rst | 978 - The number of link layer pause packets received on a physical port. If
984 - The number of link layer pause packets transmitted on a physical port. If
1003 head of line drop, pause from the network, etc.
1121 time, reaching time out and disabling transmission of pause frames. on
1122 the period where pause frames were disabled, drop could have been
1165 - The number of pause packets received on the physical port. If this
1168 only enabled when global pause mode is enabled.
1172 - The duration of pause received (in microSec) on the physical port. The
1176 only enabled when global pause mode is enabled.
1180 - The number of pause packets transmitted on a physical port. If this
[all …]
|
| /Documentation/userspace-api/media/v4l/ |
| D | vidioc-encoder-cmd.rst | 125 - Pause the encoder. When the encoder has not been started yet, the
131 - Resume encoding after a PAUSE command. When the encoder has not
168 The application sent a PAUSE or RESUME command when the encoder was
|
| D | vidioc-decoder-cmd.rst | 180 - Pause the decoder. When the decoder has not been started yet, the
187 - Resume decoding after a PAUSE command. When the decoder has not
217 The application sent a PAUSE or RESUME command when the decoder was
|
| /Documentation/driver-api/tty/ |
| D | n_gsm.rst | 100 pause();
190 pause();
|
| /Documentation/networking/device_drivers/ethernet/3com/ |
| D | vortex.rst | 162 PAUSE command, which means that they will stop sending packets for a
163 short period if they receive a PAUSE frame from the link partner.
171 The 3com cards appear to only respond to PAUSE frames which are
173 do not honour PAUSE frames which are sent to the station MAC address.
|
| /Documentation/networking/ |
| D | statistics.rst | 77 to configure pause frames can report corresponding hardware counters::
80 Pause parameters for eth0:
|
| D | phy.rst | 250 word which is used to negotiate the duplex and pause modes with the
272 duplex, pause or other settings. This is dependent on the MAC and/or
336 Pause frames / flow control
339 The PHY does not participate directly in flow control/pause frames except by
342 controller supports such a thing. Since flow control/pause frames generation
|
| /Documentation/input/devices/ |
| D | atarikbd.rst | 151 It remains in this mode until reset or commanded into another mode. The PAUSE
162 until reset or commanded into another mode. The PAUSE command in this mode not
424 PAUSE OUTPUT
445 The output is stopped only at the end of the current 'even'. If the PAUSE
447 will still be transmitted to conclusion and then the PAUSE will take effect.
449 MONITORING mode, the PAUSE OUTPUT command also temporarily stops the
|
| /Documentation/security/ |
| D | sak.rst | 30 choose CTRL-ALT-PAUSE.
|
| /Documentation/devicetree/bindings/memory-controllers/ |
| D | samsung,exynos5422-dmc.yaml | 79 are used for enabling a 'pause' feature and are not exposed by clock
|
| /Documentation/admin-guide/device-mapper/ |
| D | writecache.rst | 74 pause writeback if there was some write I/O redirected to
|
123