Searched full:referred (Results 1 – 25 of 179) sorted by relevance
12345678
| /Documentation/devicetree/bindings/fpga/ |
| D | altera-passive-serial.txt | 4 referred to as "passive serial".
15 - nconfig-gpios: config pin (referred to as nCONFIG in the manual)
16 - nstat-gpios: status pin (referred to as nSTATUS in the manual)
19 - confd-gpios: confd pin (referred to as CONF_DONE in the manual)
|
| D | xlnx,fpga-selectmap.yaml | 39 config pin (referred to as PROGRAM_B in the manual)
44 config status pin (referred to as DONE in the manual)
50 (referred to as INIT_B in the manual)
55 chip select pin (referred to as CSI_B in the manual)
61 read/write select pin (referred to as RDWR_B in the manual)
|
| D | xlnx,fpga-slave-serial.yaml | 14 over what is referred to as slave serial interface.The slave serial link is
41 config pin (referred to as PROGRAM_B in the manual)
46 config status pin (referred to as DONE in the manual)
52 (referred to as INIT_B in the manual)
|
| /Documentation/sound/soc/ |
| D | clocking.rst | 12 Every audio subsystem is driven by a master clock (sometimes referred to as MCLK
24 The Digital Audio Interface is usually driven by a Bit Clock (often referred to
29 clock is sometimes referred to as LRC (left right clock) or FRAME. This clock
|
| /Documentation/admin-guide/pm/ |
| D | strategies.rst | 17 significantly reduced, referred to as :doc:`sleep states <sleep-states>`. The
22 is affected by the state changes, this strategy is referred to as the
25 The other strategy, referred to as the :doc:`working-state power management
|
| D | sleep-states.rst | 32 referred to as S2I or S2Idle). It allows more energy to be saved relative to
78 This state (also referred to as STR or S2RAM), if supported, offers significant
112 This state (also referred to as Suspend-to-Disk or STD) offers the greatest
139 (referred to as the ``restore kernel``) looks for a hibernation image in
143 kernel stored in the image (referred to as the ``image kernel``), which is where
|
| D | intel_idle.rst | 30 first of which, referred to as a *hint*, can be used by the processor to
49 configurations (with reduced power draw) resulting from that are referred to
241 least) two levels of idle states (or C-states). One level, referred to as
243 level, referred to as "package C-states", covers the entire processor package
254 put the target core into the low-power state referred to as "core ``C3``" (or
260 low-power state referred to as "package ``C3``" (or ``PC3``), which happens if
|
| /Documentation/devicetree/bindings/arm/ |
| D | arm,integrator.yaml | 16 "core tiles" and referred to in the device tree as "core modules".
25 expansion modules, it is referred to as an "ASIC Development
|
| /Documentation/userspace-api/gpio/ |
| D | chardev_v1.rst | 44 on the GPIO device file is referred to as ``chip_fd``.
72 Within this documentation, the line handle file descriptor is referred to
97 Within this documentation, the line event file descriptor is referred to
|
| D | chardev.rst | 48 on the GPIO device file is referred to as ``chip_fd``.
75 Within this documentation, the line request file descriptor is referred to
|
| /Documentation/userspace-api/media/v4l/ |
| D | pixfmt-intro.rst | 46 and are referred to as "multi-planar formats". For example, a
51 3-planar case. Those sub-buffers are referred to as "*planes*".
|
| D | yuv-formats.rst | 46 sited between the two original pixels. This is referred to as centered or
54 odd number of taps. This is referred to as co-sited chroma.
|
| /Documentation/arch/powerpc/ |
| D | associativity.rst | 11 From the platform view, these groups are also referred to as domains.
14 grouping details to the OS. These are referred to as Form 0, Form 1 and Form2
69 this document, this offset will be referred to as domain distance offset.
|
| /Documentation/devicetree/bindings/mips/cavium/ |
| D | dma-engine.txt | 4 The DMA Engine will be referred to by phandle by any device that is
|
| /Documentation/firmware-guide/acpi/dsd/ |
| D | data-node-references.rst | 12 Hierarchical data extension nodes may not be referred to directly, hence this
20 The hierarchical data extension node which is referred to shall be located
|
| D | leds.rst | 15 "flash-leds" property documentation. In short, LEDs are directly referred to by
26 followed by the referred object name. That object shall be named "LED" followed
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | ti,omap4-wugen-mpu | 5 is also referred to as "WUGEN-MPU", hence the name of the binding.
|
| D | nvidia,tegra20-ictlr.txt | 5 referred to as "ictlr", hence the name of the binding.
|
| /Documentation/userspace-api/media/dvb/ |
| D | ca-set-descr.rst | 35 keys (referred as control words).
|
| /Documentation/devicetree/bindings/clock/ |
| D | brcm,bcm53573-ilp.txt | 7 This binding is used for ILP clock (sometimes referred as "slow clock")
|
| /Documentation/devicetree/bindings/leds/ |
| D | rohm,bd71828-leds.yaml | 19 The device has two LED outputs referred as GRNLED and AMBLED in data-sheet.
|
| /Documentation/devicetree/bindings/leds/backlight/ |
| D | kinetic,ktd253.yaml | 16 using pulses on the enable wire. This is sometimes referred to as
|
| /Documentation/driver-api/surface_aggregator/ |
| D | overview.rst | 35 exposed to ACPI via a shim driver (referred to as Surface ACPI Notify, or
71 (sometimes also referred to as notifications), sent from EC to host without
|
| /Documentation/devicetree/bindings/gpio/ |
| D | rockchip,rk3328-grf-gpio.yaml | 16 The GPIO_MUTE pin is referred to in the format
|
| /Documentation/networking/ |
| D | skbuff.rst | 19 to keep a struct sk_buff alive. skbs with a ``sk_buff.users != 1`` are referred
|
12345678