Searched full:refers (Results 1 – 25 of 143) sorted by relevance
123456
| /Documentation/filesystems/ext4/ |
| D | about.rst | 35 When referenced in ``preformatted text`` blocks, ``sb`` refers to fields
36 in the super block, and ``inode`` refers to fields in an inode table
|
| /Documentation/userspace-api/ |
| D | iommufd.rst | 23 In this context the capital letter (IOMMUFD) refers to the subsystem while the
24 small letter (iommufd) refers to the file descriptors created via /dev/iommu for
127 - Automatic domain - refers to an iommu domain created automatically when
131 - Manual domain - refers to an iommu domain designated by the user as the
136 - In-kernel user - refers to something like a VFIO mdev that is using the
|
| /Documentation/devicetree/bindings/dma/ |
| D | adi,axi-dmac.txt | 20 - reg: Which channel this node refers to.
38 specifier refers to the DMA channel index.
|
| /Documentation/networking/pse-pd/ |
| D | introduction.rst | 10 along with data over Ethernet cables. It usually refers to devices like
17 PSE in the IEEE 802.3 standard generally refers to equipment that provides
70 Physical Layers. In this clause, 'PSE' refers specifically to PoDL PSE, and
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-dac | 18 specific to toggle enabled channels and refers to the DAC output
49 specific to toggle enabled channels and refers to the DAC output
|
| D | procfs-attr-prev | 11 refers to itself.
|
| D | procfs-attr-current | 11 refers to itself.
|
| D | procfs-attr-exec | 12 refers to itself.
|
| D | sysfs-bus-pci-devices-pvpanic | 11 Detailed bit definition refers to section <Bit Definition>
|
| D | sysfs-bus-iio-dac-ltc2688 | 16 This raw, unscaled value refers to the dither signal amplitude.
|
| /Documentation/userspace-api/media/v4l/ |
| D | buffer.rst | 189 this field when ``type`` refers to a capture stream, applications
190 when it refers to an output stream. For multiplanar formats this field
200 contains VBI data. Drivers must set it when ``type`` refers to a
201 capture stream, applications when it refers to an output stream.
327 Drivers must set this field when ``type`` refers to a capture
328 stream, applications when it refers to an output stream.
366 field when ``type`` refers to a capture stream, applications when
367 it refers to an output stream.
519 Applications can set this bit when ``type`` refers to an output
527 Applications can set this bit when ``type`` refers to an output
[all …]
|
| D | selections-common.rst | 11 sub-device API, the selection rectangle refers to the media bus format,
|
| D | vidioc-g-dv-timings.rst | 128 - Vertical front porch in lines. For interlaced formats this refers
132 - Vertical sync length in lines. For interlaced formats this refers
136 - Vertical back porch in lines. For interlaced formats this refers
|
| D | vidioc-g-ctrl.rst | 50 (e.g. if it refers to an unsupported menu index of a menu control), then
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | loongson,liointc.yaml | 64 interrupt lines. Each cell refers to a parent interrupt line from 0 to 3
65 and each bit in the cell refers to a child interrupt from 0 to 31.
|
| /Documentation/devicetree/bindings/spi/ |
| D | spi-clps711x.txt | 9 - clocks: One entry, refers to the SPI bus clock
|
| /Documentation/devicetree/bindings/mtd/ |
| D | raw-nand-chip.yaml | 97 Ready/Busy pins. Active state refers to the NAND ready state and
103 Active state refers to the NAND Write Protect state and should be
|
| /Documentation/devicetree/bindings/connector/ |
| D | usb-connector.yaml | 71 support. "dual" refers to Dual Role Port (DRP).
89 description: Data role if Type C connector supports USB data. "dual" refers
223 This property refers to maximum current capability that the current sink can
226 "1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink".
227 "2" refers to 1.5A@5V.
228 "3" refers to 3.0A@5V.
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-opal.txt | 12 - ibm,opal-id: Refers to a specific bus and used to identify it when calling
|
| /Documentation/networking/ |
| D | nf_flowtable.rst | 204 refers to the software offload mode, so there is a distinction between [OFFLOAD]
205 which refers to the software flowtable fastpath and [HW_OFFLOAD] which refers
|
| /Documentation/devicetree/bindings/bus/ |
| D | st,stm32-etzpc.yaml | 68 // In this example, the usart2 device refers to rifsc as its access
|
| D | st,stm32mp25-rifsc.yaml | 84 // In this example, the usart2 device refers to rifsc as its domain
|
| /Documentation/devicetree/bindings/pmem/ |
| D | pmem-region.txt | 4 Persistent memory refers to a class of memory devices that are:
|
| /Documentation/firmware-guide/acpi/dsd/ |
| D | graph.rst | 46 port as its key. The target object it refers to should be called "PRTX", where
54 endpoint. The object it refers to should be called "EPXY", where "X" is the
|
| /Documentation/crypto/ |
| D | intro.rst | 18 The kernel crypto API refers to all algorithms as "transformations".
|
123456