Home
last modified time | relevance | path

Searched +full:reg +full:- +full:mux (Results 1 – 25 of 229) sorted by relevance

12345678910

/Documentation/devicetree/bindings/mux/
Dreg-mux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/mux/reg-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Generic register bitfield-based multiplexer controller
10 - Peter Rosin <peda@axentia.se>
19 - reg-mux # parent device of mux controller is not syscon device
20 - mmio-mux # parent device of mux controller is syscon device
22 reg: true
24 '#mux-control-cells':
[all …]
Dgpio-mux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/mux/gpio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: GPIO-based multiplexer controller
10 - Peter Rosin <peda@axentia.se>
22 const: gpio-mux
24 mux-gpios:
28 '#mux-control-cells':
31 '#mux-state-cells':
[all …]
Dmux-controller.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/mux/mux-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Peter Rosin <peda@axentia.se>
13 A multiplexer (or mux) controller will have one, or several, consumer devices
14 that uses the mux controller. Thus, a mux controller can possibly control
16 multiplexer needed by each consumer, but a single mux controller can of course
19 A mux controller provides a number of states to its consumers, and the state
20 space is a simple zero-based enumeration. I.e. 0-1 for a 2-way multiplexer,
[all …]
Dadi,adg792a.txt4 - compatible : "adi,adg792a" or "adi,adg792g"
5 - #mux-control-cells : <0> if parallel (the three muxes are bound together
6 with a single mux controller controlling all three muxes), or <1> if
7 not (one mux controller for each mux).
8 * Standard mux-controller bindings as described in mux-controller.yaml
11 - gpio-controller : if present, #gpio-cells below is required.
12 - #gpio-cells : should be <2>
13 - First cell is the GPO line number, i.e. 0 or 1
14 - Second cell is used to specify active high (0)
18 - idle-state : if present, array of states that the mux controllers will have
[all …]
Dadi,adgs1408.txt1 Bindings for Analog Devices ADGS1408/1409 8:1/Dual 4:1 Mux
4 - compatible : Should be one of
7 * Standard mux-controller bindings as described in mux-controller.yaml
10 - gpio-controller : if present, #gpio-cells is required.
11 - #gpio-cells : should be <2>
12 - First cell is the GPO line number, i.e. 0 to 3
14 - Second cell is used to specify active high (0)
18 - idle-state : if present, the state that the mux controller will have
28 * One mux controller.
29 * Mux state set to idle as is (no idle-state declared)
[all …]
/Documentation/devicetree/bindings/net/
Dmdio-mux-multiplexer.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-multiplexer.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of MDIO mux when MDIO mux is defined as a consumer
14 of a mux producer device. The mux producer can be of any type like mmio mux
15 producer, gpio mux producer or generic register based mux producer.
19 - $ref: /schemas/net/mdio-mux.yaml#
23 const: mdio-mux-multiplexer
[all …]
Dmdio-mux-mmioreg.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/net/mdio-mux-mmioreg.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Properties for an MDIO bus multiplexer controlled by a memory-mapped device
10 - Andrew Lunn <andrew@lunn.ch>
13 This is a special case of a MDIO bus multiplexer. A memory-mapped device,
14 like an FPGA, is used to control which child bus is connected. The mdio-mux
15 node must be a child of the memory-mapped device. The driver currently only
16 supports devices with 8, 16 or 32-bit registers.
[all …]
Dbrcm,mdio-mux-iproc.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/net/brcm,mdio-mux-iproc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Florian Fainelli <f.fainelli@gmail.com>
14 external to SoCs and could accept MDIO transaction compatible to C-22 or
15 C-45 Clause. When child bus is selected, one needs to select these two
19 - $ref: /schemas/net/mdio-mux.yaml#
23 const: brcm,mdio-mux-iproc
25 reg:
[all …]
Dbrcm,bcm6368-mdio-mux.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/net/brcm,bcm6368-mdio-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Álvaro Fernández Rojas <noltari@gmail.com>
18 - $ref: mdio-mux.yaml#
22 const: brcm,bcm6368-mdio-mux
24 reg:
28 - compatible
29 - reg
[all …]
/Documentation/devicetree/bindings/soc/microchip/
Dmicrochip,sparx5-cpu-syscon.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/soc/microchip/microchip,sparx5-cpu-syscon.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Lars Povlsen <lars.povlsen@microchip.com>
15 - const: microchip,sparx5-cpu-syscon
16 - const: syscon
17 - const: simple-mfd
19 reg:
22 mux-controller:
[all …]
/Documentation/devicetree/bindings/soc/ti/
Dti,am654-serdes-ctrl.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/soc/ti/ti,am654-serdes-ctrl.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Nishanth Menon <nm@ti.com>
15 - const: ti,am654-serdes-ctrl
16 - const: syscon
17 - const: simple-mfd
19 reg:
22 mux-controller:
[all …]
/Documentation/devicetree/bindings/clock/
Dnxp,imx95-display-master-csr.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/clock/nxp,imx95-display-master-csr.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Peng Fan <peng.fan@nxp.com>
15 - const: nxp,imx95-display-master-csr
16 - const: syscon
18 reg:
21 power-domains:
27 '#clock-cells':
[all …]
/Documentation/devicetree/bindings/i2c/
Di2c-mux-gpmux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/i2c/i2c-mux-gpmux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: General Purpose I2C Bus Mux
10 - Peter Rosin <peda@axentia.se>
13 This binding describes an I2C bus multiplexer that uses a mux controller
14 from the mux subsystem to route the I2C signals.
16 .-----. .-----.
18 .------------. '-----' '-----'
[all …]
Di2c-mux-reg.txt1 Register-based I2C Bus Mux
7 - compatible: i2c-mux-reg
8 - i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
10 * Standard I2C mux properties. See i2c-mux.yaml in this directory.
11 * I2C child bus nodes. See i2c-mux.yaml in this directory.
14 - reg: this pair of <offset size> specifies the register to control the mux.
15 The <offset size> depends on its parent node. It can be any memory-mapped
16 address. The size must be either 1, 2, or 4 bytes. If reg is omitted, the
18 - little-endian: The existence indicates the register is in little endian.
19 - big-endian: The existence indicates the register is in big endian.
[all …]
Di2c-mux-ltc4306.txt5 - compatible: Must contain one of the following.
7 - reg: The I2C address of the device.
11 - Standard I2C mux properties. See i2c-mux.yaml in this directory.
12 - I2C child bus nodes. See i2c-mux.yaml in this directory.
16 - enable-gpios: Reference to the GPIO connected to the enable input.
17 - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
20 - gpio-controller: Marks the device node as a GPIO Controller.
21 - #gpio-cells: Should be two. The first cell is the pin number and
24 - ltc,downstream-accelerators-enable: Enables the rise time accelerators
26 - ltc,upstream-accelerators-enable: Enables the rise time accelerators
[all …]
Di2c-mux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/i2c/i2c-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Peter Rosin <peda@axentia.se>
18 i2c child busses and other child nodes, the 'i2c-mux' subnode can be used for
19 populating the i2c child busses. If an 'i2c-mux' subnode is present, only
24 pattern: '^(i2c-?)?mux'
26 '#address-cells':
29 '#size-cells':
[all …]
Di2c-mux-pca954x.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/i2c/i2c-mux-pca954x.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
23 - enum:
24 - maxim,max7356
25 - maxim,max7357
26 - maxim,max7358
27 - maxim,max7367
[all …]
Di2c-mux-gpio.yaml1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/i2c/i2c-mux-gpio.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: GPIO-based I2C Bus Mux
10 - Wolfram Sang <wsa@kernel.org>
15 +-----+ +-----+
17 +------------+ +-----+ +-----+
19 | | /--------+--------+
20 | +------+ | +------+ child bus A, on GPIO value set to 0
[all …]
/Documentation/devicetree/bindings/media/
Dvideo-mux.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/media/video-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sakari Ailus <sakari.ailus@linux.intel.com>
11 - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
20 const: video-mux
22 mux-controls:
25 '#address-cells':
28 '#size-cells':
[all …]
/Documentation/devicetree/bindings/board/
Dfsl,fpga-qixis-i2c.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/board/fsl,fpga-qixis-i2c.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Freescale on-board FPGA connected on I2C bus
10 - Frank Li <Frank.Li@nxp.com>
15 - items:
16 - enum:
17 - fsl,bsc9132qds-fpga
18 - const: fsl,fpga-qixis-i2c
[all …]
/Documentation/devicetree/bindings/soc/imx/
Dfsl,imx-iomuxc-gpr.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/soc/imx/fsl,imx-iomuxc-gpr.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Peng Fan <peng.fan@nxp.com>
19 - items:
20 - enum:
21 - fsl,imx6q-iomuxc-gpr
22 - fsl,imx8mq-iomuxc-gpr
23 - const: syscon
[all …]
/Documentation/devicetree/bindings/interrupt-controller/
Dmrvl,intc.yaml1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/interrupt-controller/mrvl,intc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Andrew Lunn <andrew@lunn.ch>
11 - Gregory Clement <gregory.clement@bootlin.com>
14 - if:
19 const: marvell,orion-intc
22 - mrvl,intc-nr-irqs
23 - if:
[all …]
/Documentation/devicetree/bindings/clock/ti/
Dmux.txt1 Binding for TI mux clock.
4 register-mapped multiplexer with multiple input clock signals or
22 "index-starts-at-one" modified the scheme as follows:
29 The binding must provide the register to control the mux. Optionally
34 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
37 - compatible : shall be "ti,mux-clock" or "ti,composite-mux-clock".
38 - #clock-cells : from common clock binding; shall be set to 0.
39 - clocks : link phandles of parent clocks
40 - reg : register offset for register controlling adjustable mux
43 - clock-output-names : from common clock binding.
[all …]
/Documentation/devicetree/bindings/spi/
Dspi-mux.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/spi/spi-mux.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
13 setting of the multiplexer to a channel needs to be done by a specific SPI mux
16 MOSI /--------------------------------+--------+--------+--------\
17 MISO |/------------------------------+|-------+|-------+|-------\|
18 SCL ||/----------------------------+||------+||------+||------\||
20 +------------+ ||| ||| ||| |||
21 | SoC ||| | +-+++-+ +-+++-+ +-+++-+ +-+++-+
[all …]
/Documentation/devicetree/bindings/
Dunittest.txt6 - compatible: must be "unittest"
20 - compatible: must be unittest-i2c-bus
25 unittest-i2c-bus {
26 compatible = "unittest-i2c-bus";
34 - compatible: must be unittest-i2c-dev
39 unittest-i2c-dev {
40 compatible = "unittest-i2c-dev";
43 4) OF unittest i2c mux device
45 ** I2C unittest mux
48 - compatible: must be unittest-i2c-mux
[all …]

12345678910