Searched full:respond (Results 1 – 25 of 100) sorted by relevance
1234
| /Documentation/ABI/testing/ |
| D | sysfs-bus-fsi-devices-sbefifo | 6 timeout; i.e. the SBE did not respond within the time allotted
|
| D | sysfs-class-power-ltc4162l | 73 remain in this mode (and no longer respond to I2C commands)
|
| /Documentation/devicetree/bindings/rtc/ |
| D | isil,isl12026.txt | 4 registers respond at bus address 0x6f, and the EEPROM array responds
|
| /Documentation/devicetree/bindings/i2c/ |
| D | hpe,gxp-i2c.yaml | 34 arm and respond to interrupts from its engine. Each bit in the
|
| /Documentation/process/ |
| D | 6.Followthrough.rst | 44 impulse to respond in kind. Code review is about the code, not about
66 that the reviewer is asking you to fix. And respond back to the reviewer:
184 respond to these reports is a matter of basic pride in your work. If that
216 really only one way to respond: be pleased that your problem got solved and
|
| /Documentation/i2c/ |
| D | slave-testunit-backend.rst | 137 Partial command. This test will respond to a block process call as defined by
170 128 bytes. However, it will only respond if the read message is connected to
230 If the host does not respond to the alert within 1 second, the test will be
|
| D | ten-bit-addresses.rst | 8 address 0x10 (though a single device could respond to both of them).
|
| D | i2c-stub.rst | 16 quick commands to the specified addresses; it will respond to the other
|
| D | summary.rst | 53 target (needs hardware support) and respond to another controller on the bus.
|
| D | fault-codes.rst | 22 to respond correctly. Other code may need to rely on YOUR code reporting
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | chrontel,ch7322.yaml | 42 the device will respond to power status requests with "standby"
|
| /Documentation/driver-api/xilinx/ |
| D | eemi.rst | 17 device to issue or respond to power management requests.
|
| /Documentation/devicetree/bindings/display/ |
| D | dsi-controller.yaml | 60 peripherals respond to more than a single virtual channel. In that
|
| /Documentation/maintainer/ |
| D | feature-and-driver-maintainers.rst | 34 reviewers should try to respond quicker than what is the usual patch
81 Maintainers furthermore should respond to reports about other kinds of
|
| /Documentation/w1/masters/ |
| D | omap-hdq.rst | 29 does not respond with a presence pulse as it does in the 1-Wire protocol.
|
| /Documentation/scsi/ |
| D | megaraid.rst | 10 Different classes of controllers from LSI Logic accept and respond to the
|
| D | BusLogic.rst | 306 respond to synchronous transfer negotiation for UltraSCSI speed. AutoSCSI
324 The BT-948/958/958D will not respond to any of the ISA compatible I/O ports
325 that previous BusLogic SCSI Host Adapters respond to. This driver supports
375 UltraSCSI operation, or where existing SCSI devices do not properly respond
500 respond correctly when Logical Units above 0 are addressed.
|
| /Documentation/driver-api/pldmfw/ |
| D | index.rst | 66 the device. For each component, the firmware may respond with an
|
| /Documentation/usb/ |
| D | raw-gadget.rst | 25 descriptors. Note that the UDC driver might respond to some requests on
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | ti,tsc2005.yaml | 44 if the touchscreen does not respond after the configured time
|
| /Documentation/driver-api/ |
| D | switchtec.rst | 26 respond with a 4-byte return code and up to 1KB of command-specific
|
| /Documentation/hid/ |
| D | uhid.rst | 49 register the device. UHID will respond with a UHID_START event. You can now
176 parallel. However, if you fail to respond with a UHID_GET_REPORT_REPLY, the
|
| /Documentation/block/ |
| D | null_blk.rst | 76 Whether or not to use a memory buffer to respond to IO requests
80 1 Use a memory buffer to respond to IO requests
|
| /Documentation/input/devices/ |
| D | alps.rst | 31 All ALPS touchpads should respond to the "E6 report" command sequence:
32 E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or
53 EC-EC-EC-E9 places the device in command mode, and the device will respond
|
| /Documentation/filesystems/ |
| D | befs.rst | 34 respond to the address given above...
|
1234