Home
last modified time | relevance | path

Searched +full:sck +full:- +full:gpios (Results 1 – 11 of 11) sorted by relevance

/Documentation/devicetree/bindings/spi/
Dspi-gpio.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/spi/spi-gpio.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: SPI-GPIO
10 - Rob Herring <robh@kernel.org>
13 This represents a group of 3-n GPIO lines used for bit-banged SPI on
17 - $ref: /schemas/spi/spi-controller.yaml#
21 const: spi-gpio
23 sck-gpios:
[all …]
/Documentation/devicetree/bindings/iio/adc/
Davia-hx711.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/iio/adc/avia-hx711.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Andreas Klinger <ak@it-klinger.de>
13 Bit-banging driver using two GPIOs:
14 - sck-gpio gives a clock to the sensor with 24 cycles for data retrieval
17 - dout-gpio is the sensor data the sensor responds to the clock
25 - avia,hx711
27 sck-gpios:
[all …]
/Documentation/devicetree/bindings/fpga/
Dlattice-ice40-fpga-mgr.txt4 - compatible: Should contain "lattice,ice40-fpga-mgr"
5 - reg: SPI chip select
6 - spi-max-frequency: Maximum SPI frequency (>=1000000, <=25000000)
7 - cdone-gpios: GPIO input connected to CDONE pin
8 - reset-gpios: Active-low GPIO output connected to CRESET_B pin. Note
10 FPGA will enter Master SPI mode and drive SCK with a
16 compatible = "lattice,ice40-fpga-mgr";
18 spi-max-frequency = <1000000>;
19 cdone-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
20 reset-gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
/Documentation/devicetree/bindings/pinctrl/
Dmarvell,dove-pinctrl.txt3 Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
7 - compatible: "marvell,dove-pinctrl"
8 - clocks: (optional) phandle of pdma clock
9 - reg: register specifiers of MPP, MPP4, and PMU MPP registers
23 uart1(cts), lcd-spi(cs1), pmu*
27 mpp7 7 gpio, pmu, uart3(rxd), sdio1(ledctrl), spi1(sck), pmu*
31 mpp11 11 gpio, pmu, sata(prsnt), sata-1(act), sdio0(ledctrl),
39 mpp16 16 gpio, uart3(rts), sdio0(cd), ac97(sdi1), lcd-spi(cs1)
41 ac97-1(sysclko)
43 mpp19 19 gpio, uart3(rxd), sdio0(ledctrl), twsi(sck)
[all …]
/Documentation/devicetree/bindings/display/panel/
Dsamsung,lms397kf04.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
13 - Linus Walleij <linus.walleij@linaro.org>
16 - $ref: panel-common.yaml#
17 - $ref: /schemas/spi/spi-peripheral-props.yaml#
26 reset-gpios: true
28 vci-supply:
32 vccio-supply:
38 spi-cpha: true
[all …]
Dsamsung,s6d27a1.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
13 - Markuss Broks <markuss.broks@gmail.com>
16 - $ref: panel-common.yaml#
17 - $ref: /schemas/spi/spi-peripheral-props.yaml#
33 reset-gpios: true
35 vci-supply:
39 vccio-supply:
45 spi-cpha: true
[all …]
Dsamsung,lms380kf01.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
14 - Linus Walleij <linus.walleij@linaro.org>
17 - $ref: panel-common.yaml#
18 - $ref: /schemas/spi/spi-peripheral-props.yaml#
34 reset-gpios: true
36 vci-supply:
40 vccio-supply:
46 spi-cpha: true
[all …]
/Documentation/devicetree/bindings/sound/
Daxentia,tse850-pcm5142.txt1 Devicetree bindings for the Axentia TSE-850 audio complex
4 - compatible: "axentia,tse850-pcm5142"
5 - axentia,cpu-dai: The phandle of the cpu dai.
6 - axentia,audio-codec: The phandle of the PCM5142 codec.
7 - axentia,add-gpios: gpio specifier that controls the mixer.
8 - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1.
9 - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2.
10 - axentia,ana-supply: Regulator that supplies the output amplifier. Must
11 support voltages in the 2V - 20V range, in 1V steps.
13 The schematics explaining the gpios are as follows:
[all …]
/Documentation/iio/
Dad7944.rst1 .. SPDX-License-Identifier: GPL-2.0-only
25 ----------------
29 CS mode, 3-wire, without busy indicator
32 .. code-block::
34 +-------------+
35 +--------------------| CS |
37 VIO +--------------------+ | HOST |
39 +--->| SDI AD7944 SDO |-------->| SDI |
40 | SCK | | |
41 +--------------------+ | |
[all …]
/Documentation/driver-api/gpio/
Dintro.rst10 GPIOs in drivers, and how to write a driver for a device that provides GPIOs
17 A "General Purpose Input/Output" (GPIO) is a flexible software-controlled
22 which GPIOs. Drivers can be written generically, so that board setup code
25 System-on-Chip (SOC) processors heavily rely on GPIOs. In some cases, every
26 non-dedicated pin can be configured as a GPIO; and most chips have at least
28 provide GPIOs; multifunction chips like power managers, and audio codecs
31 Most PC southbridges have a few dozen GPIO-capable pins (with only the BIOS
34 The exact capabilities of GPIOs vary between systems. Common options:
36 - Output values are writable (high=1, low=0). Some chips also have
38 value might be driven, supporting "wire-OR" and similar schemes for the
[all …]
Ddrivers-on-gpio.rst6 the right in-kernel and userspace APIs/ABIs for the job, and that these
10 - leds-gpio: drivers/leds/leds-gpio.c will handle LEDs connected to GPIO
13 - ledtrig-gpio: drivers/leds/trigger/ledtrig-gpio.c will provide a LED trigger,
15 (and that LED may in turn use the leds-gpio as per above).
17 - gpio-keys: drivers/input/keyboard/gpio_keys.c is used when your GPIO line
20 - gpio-keys-polled: drivers/input/keyboard/gpio_keys_polled.c is used when your
24 - gpio_mouse: drivers/input/mouse/gpio_mouse.c is used to provide a mouse with
25 up to three buttons by simply using GPIOs and no mouse port. You can cut the
29 - gpio-beeper: drivers/input/misc/gpio-beeper.c is used to provide a beep from
31 off/on, for an actual PWM waveform, see pwm-gpio below.)
[all …]