| /Documentation/devicetree/bindings/mmc/ |
| D | amlogic,meson-mx-sdio.txt | 1 * Amlogic Meson6, Meson8 and Meson8b SDIO/MMC controller
4 for MMC, SD, SDIO and SDHC types of memory cards.
14 - "amlogic,meson8-sdio"
15 - "amlogic,meson8b-sdio"
16 along with the generic "amlogic,meson-mx-sdio"
40 compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio";
|
| D | marvell,orion-sdio.yaml | 4 $id: http://devicetree.org/schemas/mmc/marvell,orion-sdio.yaml#
7 title: Marvell orion-sdio controller
18 const: marvell,orion-sdio
40 compatible = "marvell,orion-sdio";
|
| D | mmc-controller.yaml | 28 The cell is the SDIO function number if a function subnode is used.
94 - for SD/SDIO cards the SDR104 mode has a max supported
112 line. Not used in combination with eMMC or SDIO.
175 cap-sdio-irq:
178 enable SDIO IRQ signalling on this interface
243 no-sdio:
246 Controller is limited to send SDIO commands during
294 SDIO only. Preserves card power during a suspend/resume cycle.
299 SDIO only. Enables wake up of host system on SDIO IRQ assertion.
316 sequence. To successfully detect an (e)MMC/SD/SDIO card, that
[all …]
|
| D | usdhi6rol0.txt | 1 * Renesas usdhi6rol0 SD/SDIO host controller
7 - interrupts: 3 interrupts, named "card detect", "data" and "SDIO" must be
32 interrupt-names = "card detect", "data", "SDIO";
|
| D | aspeed,sdhci.yaml | 8 title: ASPEED SD/SDIO/MMC Controller
15 The ASPEED SD/SDIO/eMMC controller exposes two slots implementing the SDIO
39 description: The SD/SDIO controller clock gate
|
| D | ti-omap-hsmmc.txt | 4 provides an interface for MMC, SD, and SDIO types of memory cards.
85 This SOC is missing the swakeup line, it will not detect SDIO irq
106 Prepare idle to remux dat1 as a gpio, and default to remux it back as sdio
113 3. specify the gpio irq used for detecting sdio irq in suspend
116 polling". Also check the "sdio irq mode" in /sys/kernel/debug/mmc0/regs. Mind
117 not every application needs SDIO irq, e.g. MMC cards.
|
| D | sprd,sdhci-r11.yaml | 27 - description: SDIO source clock
34 - const: sdio
91 clock-names = "sdio", "enable", "2x_enable";
104 no-sdio;
|
| D | amlogic,meson-gx-mmc.yaml | 11 interface for SD, eMMC and SDIO devices
52 like on the G12A dedicated SDIO controller.
|
| D | marvell,xenon-sdhci.yaml | 84 All those types of PHYs can support eMMC, SD and SDIO. Please note that
216 no-sdio;
222 // For SD/SDIO
255 no-sdio;
263 // For SD/SDIO with compatible "marvell,armada-3700-sdhci":
|
| D | ingenic,mmc.yaml | 79 cap-sdio-irq;
104 cap-sdio-irq;
|
| D | sdhci-pxa.yaml | 67 Optional for supporting PXA168 SDIO IRQ errata to switch CMD pin between
68 SDIO CMD and GPIO mode.
|
| D | pxa-mmc.txt | 3 Driver bindings for the PXA MCI (MMC/SDIO) interfaces
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | loongson,ls2k-pinctrl.yaml | 42 enum: [gpio, sdio, can1, can0, pwm3, pwm2, pwm1, pwm0, i2c1, i2c0,
47 enum: [gpio, sdio, can1, can0, pwm3, pwm2, pwm1, pwm0, i2c1, i2c0,
65 sdio_pins_default: sdio-pins {
66 sdio-pinmux {
67 groups = "sdio";
68 function = "sdio";
71 sdio-det-pinmux {
|
| D | marvell,kirkwood-pinctrl.txt | 39 mpp12 12 gpo, sdio(clk)
40 mpp13 13 gpio, sdio(cmd), uart1(txd)
41 mpp14 14 gpio, sdio(d0), uart1(rxd), mii(col)
42 mpp15 15 gpio, sdio(d1), uart0(rts), uart1(txd)
43 mpp16 16 gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs)
44 mpp17 17 gpio, sdio(d3)
77 mpp12 12 gpo, sdio(clk)
78 mpp13 13 gpio, sdio(cmd), uart1(txd)
79 mpp14 14 gpio, sdio(d0), uart1(rxd), mii(col)
80 mpp15 15 gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act)
[all …]
|
| /Documentation/devicetree/bindings/arm/marvell/ |
| D | ap80x-system-controller.txt | 51 mpp0 0 gpio, sdio(clk), spi0(clk)
52 mpp1 1 gpio, sdio(cmd), spi0(miso)
53 mpp2 2 gpio, sdio(d0), spi0(mosi)
54 mpp3 3 gpio, sdio(d1), spi0(cs0n)
55 mpp4 4 gpio, sdio(d2), i2c0(sda)
56 mpp5 5 gpio, sdio(d3), i2c0(sdk)
57 mpp6 6 gpio, sdio(ds)
58 mpp7 7 gpio, sdio(d4), uart1(rxd)
59 mpp8 8 gpio, sdio(d5), uart1(txd)
60 mpp9 9 gpio, sdio(d6), spi0(cs1n)
[all …]
|
| D | cp110-system-controller.txt | 40 - 0 5 SDIO core
46 - 1 4 SDIO
123 … mii(txerr), mss_spi(miso), tdm(drx), au(i2sextclk), au(i2sdi), ge(mdio), sdio(v18_en), pcie1(clkr…
124 mpp33 33 gpio, mii(txclk), sdio(pwr10), mss_spi(csn), tdm(fsync), au(i2smclk), sdio(bus_pwr), xg(md…
125 mpp34 34 gpio, mii(rxerr), sdio(pwr11), mss_spi(mosi), tdm(dtx), au(i2slrclk), sdio(wr_protect), ge…
126 mpp35 35 gpio, sata1(present_act), i2c1(sda), mss_spi(clk), tdm(pclk), au(i2sdo_spdifo), sdio(card_…
130 mpp39 39 gpio, sdio(wr_protect), au(i2sbclk), ptp(clk), spi0(csn1), sata1(present_act), mss_gpio0
131 mpp40 40 gpio, sdio(pwr11), synce1(clk), mss_i2c(sda), au(i2sdo_spdifo), ptp(pclk_out), spi0(clk), …
132 mpp41 41 gpio, sdio(pwr10), sdio(bus_pwr), mss_i2c(sck), au(i2slrclk), ptp(pulse), spi0(mosi), uart…
133 mpp42 42 gpio, sdio(v18_en), sdio(wr_protect), synce2(clk), au(i2smclk), mss_uart(txd), spi0(miso),…
[all …]
|
| /Documentation/devicetree/bindings/net/bluetooth/ |
| D | mediatek,mt7921s-bluetooth.yaml | 13 MT7921S is an SDIO-attached dual-radio WiFi+Bluetooth Combo chip; each
14 function is its own SDIO function on a shared SDIO interface. The chip
16 This binding only covers the Bluetooth SDIO function, with one device
17 node describing only this SDIO function.
|
| /Documentation/devicetree/bindings/net/ |
| D | marvell-bt-8xxx.txt | 1 Marvell 8897/8997 (sd8897/sd8997) bluetooth devices (SDIO or USB based)
3 The 8997 devices supports multiple interfaces. When used on SDIO interfaces,
10 * "marvell,sd8897-bt" (for SDIO)
11 * "marvell,sd8997-bt" (for SDIO)
18 This is only applicable to SDIO devices.
26 - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the
42 Example for SDIO device follows (calibration data is also available in
|
| /Documentation/devicetree/bindings/clock/ |
| D | mvebu-gated-clock.txt | 21 17 sdio SDHCI Host
40 17 sdio SDHCI Host
72 17 sdio SDIO
91 17 sdio SDIO
111 17 sdio SDHCI Host
128 17 sdio SDHCI Host
161 4 sdio SDIO Cntrl
201 sdio0: sdio@92000 {
|
| D | armada3700-periph-clock.txt | 46 10 sdio SDIO
|
| /Documentation/devicetree/bindings/net/wireless/ |
| D | silabs,wfx.yaml | 18 The WF200 can be connected via SPI or via SDIO.
20 For SDIO:
23 sufficient for the SDIO devices).
25 It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without
43 When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is
50 used, this property is required. When SDIO is used, the "in-band"
51 interrupt provided by the SDIO bus is used unless an interrupt is defined
60 For SDIO, the reset gpio should declared using a mmc-pwrseq.
|
| D | marvell,sd8787.yaml | 7 title: Marvell 8787/8897/8978/8997 (sd8787/sd8897/sd8978/sd8997/pcie8997) SDIO/PCIE devices
14 This node provides properties for describing the Marvell SDIO/PCIE wireless device.
15 The node is expected to be specified as a child node to the SDIO/PCIE controller that
|
| D | ti,wlcore.yaml | 13 The wl12xx/wl18xx chips can be connected via SPI or via SDIO.
37 SDIO.
127 // SDIO example:
|
| D | brcm,bcm4329-fmac.yaml | 7 title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices
58 description: SDIO function number for the device (for most cases
73 description: Drive strength used for the SDIO pins on the device in mA.
|
| /Documentation/driver-api/mmc/ |
| D | index.rst | 4 MMC/SD/SDIO card support
|