Searched full:selecting (Results 1 – 25 of 96) sorted by relevance
1234
| /Documentation/leds/ |
| D | ledtrig-usbport.rst | 9 It requires selecting USB ports that should be observed. All available ones are
10 listed as separated entries in a "ports" subdirectory. Selecting is handled by
13 Please note that this trigger allows selecting multiple USB ports for a single
|
| /Documentation/userspace-api/ |
| D | sysfs-platform_profile.rst | 16 API for selecting the platform profile of these automatic mechanisms.
18 Note that this API is only for selecting the platform profile, it is
23 Specifically when selecting a high performance profile the actual achieved
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-led-trigger-usbport | 8 selected for the USB port trigger. Selecting ports makes trigger
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | actions,s900-pinctrl.txt | 57 These pins are used for selecting the pull control and schmitt
91 group. These pin groups are used for selecting the pinmux
113 These pin groups are used for selecting the drive strength
126 These pin groups are used for selecting the slew rate
|
| D | actions,s700-pinctrl.txt | 57 These pins are used for selecting the pull control and schmitt
85 group. These pin groups are used for selecting the pinmux
103 These pin groups are used for selecting the drive strength
|
| /Documentation/admin-guide/hw-vuln/ |
| D | index.rst | 6 possible mitigations along with guidance for selecting mitigations if they
|
| /Documentation/networking/ |
| D | secid.rst | 10 the label of the flow. This label of the flow is currently used in selecting
|
| D | tc-queue-filters.rst | 22 Likewise, on the receive side, the two filters for selecting set of
|
| D | mptcp.rst | 79 The Packet Scheduler is in charge of selecting which available *subflow(s)* to
94 On Linux, MPTCP can be used by selecting MPTCP instead of TCP when creating the
|
| /Documentation/devicetree/bindings/clock/ |
| D | gpio-mux-clock.yaml | 25 description: GPIO reference for selecting the parent clock.
|
| /Documentation/block/ |
| D | deadline-iosched.rst | 9 Selecting IO schedulers
12 selecting an io scheduler on a per-device basis.
|
| /Documentation/userspace-api/media/v4l/ |
| D | common.rst | 12 - Changing device properties, selecting a video and audio input, video
|
| D | ext-ctrls-image-process.rst | 40 The configuration of the frame rate is performed by selecting the desired
|
| /Documentation/devicetree/bindings/sound/ |
| D | adi,adau1701.txt | 19 - adi,pin-config: An array of 12 numerical values selecting one of the
|
| /Documentation/userspace-api/media/dvb/ |
| D | fe-dishnetwork-send-legacy-cmd.rst | 38 It provides a non-standard method for selecting Diseqc voltage on the
|
| D | fe-set-tone.rst | 44 capability of selecting the band. So, it is recommended that applications
|
| D | frontend.rst | 43 control the antenna subsystem, selecting the polarization and choosing
|
| /Documentation/hwmon/ |
| D | lm93.rst | 95 #P1_PROCHOT and #P2_PROCHOT, respectively. Selecting a value not in this
150 are constrained by the hardware. Selecting a value which is not available
160 frequency values are constrained by the hardware. Selecting a value which is
245 the hardware. Selecting a value which is not available will cause the driver
258 The available ramp times are constrained by the hardware. Selecting a value
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | bu21013.txt | 6 - reset-gpios : GPIO pin enabling (selecting) chip (CS)
|
| /Documentation/scheduler/ |
| D | sched-eevdf.rst | 19 zero and calculates a virtual deadline (VD) for each, selecting the task
|
| /Documentation/devicetree/bindings/leds/ |
| D | skyworks,aat1290.yaml | 16 respectively. In order to add a capability of selecting the strobe signal
|
| /Documentation/maintainer/ |
| D | feature-and-driver-maintainers.rst | 97 Selecting the maintainer
101 this section provides guidance on selecting one and describes common
|
| /Documentation/admin-guide/media/ |
| D | building.rst | 64 The ``HDMI CEC drivers`` option allow selecting platform and USB drivers
122 The remote controller menu allows selecting drivers for specific devices.
143 The ``Remote controller decoders`` option allows selecting the
|
| /Documentation/devicetree/bindings/phy/ |
| D | phy-rockchip-naneng-combphy.yaml | 61 When selecting this option an externally 100MHz differential
|
| /Documentation/devicetree/bindings/mfd/ |
| D | cirrus,lochnagar.yaml | 190 A property selecting which of the CODEC minicard micbias outputs
216 A property selecting which of the CODEC minicard micbias outputs
|
1234