Searched full:selects (Results 1 – 25 of 190) sorted by relevance
12345678
| /Documentation/devicetree/bindings/spi/ |
| D | nuvoton,npcm-fiu.txt | 6 FIU0 and FIUx supports two chip selects,
10 FIU0 and FIUx supports two chip selects,
11 FIU1 and FIU3 supports four chip selects.
|
| D | renesas,sh-msiof.yaml | 87 Total number of chip selects (default is 1).
88 Up to 3 native chip selects are supported:
92 Hardware limitations related to chip selects:
93 - Native chip selects are always deasserted in between transfers
96 - All slaves using native chip selects must use the same spi-cs-high
98 - When using GPIO chip selects, at least one native chip select must
|
| D | spi-controller.yaml | 30 GPIOs used as chip selects.
31 If that property is used, the number of chip selects will be
32 increased automatically with max(cs-gpios, hardware chip selects).
90 Total number of chip selects.
|
| D | spi-cadence.yaml | 37 Number of chip selects used. If a decoder is used,
38 this will be the number of chip selects after the
|
| D | renesas,rspi.yaml | 90 Total number of native chip selects.
91 Hardware limitations related to chip selects:
92 - When using GPIO chip selects, at least one native chip select must
|
| D | spi-davinci.txt | 18 - num-cs: Number of chip selects. This includes internal as well as
19 GPIO chip selects.
39 - cs-gpios: gpio chip selects
|
| /Documentation/devicetree/bindings/bus/ |
| D | qcom,ebi2.yaml | 17 NOR flash memories), WE (write enable). This on top of 6 different chip selects
27 The chip selects have the following memory range assignments. This region of
44 this is something just used on the FAST chip selects and that the SLOW
45 chip selects are understood fully. There is also a "byte device enable"
50 together, or if some chip selects are hardwired to be FAST and others are SLOW
112 # SLOW chip selects
165 # FAST chip selects
|
| D | socionext,uniphier-system-bus.yaml | 12 some control signals. It supports up to 8 banks (chip selects).
62 description: Devices attached to chip selects
|
| /Documentation/ABI/testing/ |
| D | sysfs-driver-aspeed-uart-routing | 5 Description: Selects the RX source of the UARTx device.
24 Description: Selects the RX source of IOx serial port. The current selection
|
| D | sysfs-class-led-trigger-usbport | 12 Echoing "1" value selects USB port. Echoing "0" unselects it.
|
| D | sysfs-platform-i2c-demux-pinctrl | 17 This file selects/shows the active I2C master for a demultiplexed
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | qcom,pmic-mpp.yaml | 121 Selects the source for analog output. Valued values are defined in
128 Selects ATEST rail to route to GPIO when it's
135 Selects DTEST rail to route to GPIO when it's
142 Selects the source for analog input. Valid values are defined in
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | panel-timing.yaml | 147 0 selects active low, 1 selects active high.
155 0 selects active low, 1 selects active high.
163 0 selects active low, 1 selects active high.
|
| /Documentation/admin-guide/device-mapper/ |
| D | dm-queue-length.rst | 6 which selects a path with the least number of in-flight I/Os.
32 dm-queue-length selects a path with the minimum 'in-flight'.
|
| D | dm-service-time.rst | 6 which selects a path with the shortest estimated service time for
51 Basically, dm-service-time selects a path having minimum service time
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | adi,adm1177.yaml | 41 Specifies which internal voltage divider to be used. A 1 selects
42 a 7:2 voltage divider while a 0 selects a 14:1 voltage divider.
|
| /Documentation/kbuild/ |
| D | Kconfig.recursion-issue-02 | 15 # annotate this, all features that driver A selects cannot now be negated by
28 # CORE_BELL_A has some advanced feature CORE_BELL_A_ADVANCED which selects
|
| /Documentation/userspace-api/media/v4l/ |
| D | vidioc-dbg-g-chip-info.rst | 57 selects the nth bridge 'chip' on the TV card. You can enumerate all
60 zero always selects the bridge chip itself, e. g. the chip connected to
65 selects the nth sub-device. This allows you to enumerate over all
|
| D | vidioc-dbg-g-register.rst | 66 selects the nth non-sub-device chip on the TV card. The number zero
67 always selects the host chip, e. g. the chip connected to the PCI or USB
72 selects the nth sub-device.
|
| /Documentation/devicetree/bindings/soc/qcom/ |
| D | qcom,apr.yaml | 31 Selects the processor domain for apr
46 Selects the processor domain for apr
54 Selects the processor domain for gpr
|
| /Documentation/devicetree/bindings/usb/ |
| D | usb251xb.yaml | 83 selects between self- and bus-powered operation
89 selects between self- and bus-powered operation
100 selects between multi- and single-transaction-translator
106 selects between multi- and single-transaction-translator
|
| /Documentation/devicetree/bindings/mfd/ |
| D | mediatek,mt6357.yaml | 47 description: Selects MIC Bias 0 output voltage.
53 description: Selects MIC Bias 1 output voltage.
|
| /Documentation/devicetree/bindings/sound/ |
| D | cs35l36.txt | 37 Selects the source of the BST_CTL target VBST voltage for the boost
88 - cirrus,irq-drive-select : Selects the driver type of the selected interrupt
94 - cirrus,irq-gpio-select : Selects the pin to serve as the programmable
|
| /Documentation/hwmon/ |
| D | pmbus-core.rst | 220 ignored. Otherwise, a phase value of 0xff selects all phases.
228 i2c_smbus_read_word_data(), but selects page and phase first. If the chip does
230 value of 0xff selects all phases.
238 selects page first.
245 selects page first. <page> may be -1, which means "current page".
252 selects page first. <page> may be -1, which means "current page".
|
| /Documentation/devicetree/bindings/phy/ |
| D | mediatek,mt7621-pci-phy.yaml | 24 description: selects if the phy is dual-ported
|
12345678