Searched full:settle (Results 1 – 20 of 20) sorted by relevance
| /Documentation/devicetree/bindings/thermal/ |
| D | qcom-spmi-adc-tm5.yaml | 83 qcom,hw-settle-time-us:
184 qcom,hw-settle-time = <200>;
201 qcom,hw-settle-time-us = <200>;
226 qcom,hw-settle-time = <200>;
233 qcom,hw-settle-time = <200>;
251 qcom,hw-settle-time-us = <200>;
259 qcom,hw-settle-time-us = <200>;
|
| D | qcom-spmi-adc-tm-hc.yaml | 78 qcom,hw-settle-time-us:
145 qcom,hw-settle-time-us = <200>;
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | qcom,spmi-vadc.yaml | 123 qcom,hw-settle-time:
156 qcom,hw-settle-time:
179 qcom,hw-settle-time:
202 qcom,hw-settle-time:
225 qcom,hw-settle-time:
255 qcom,hw-settle-time = <200>;
298 qcom,hw-settle-time = <200>;
305 qcom,hw-settle-time = <200>;
|
| /Documentation/devicetree/bindings/media/ |
| D | samsung,exynos4210-csis.yaml | 88 samsung,csis-hs-settle:
90 description: Differential receiver (HS-RX) settle time.
166 samsung,csis-hs-settle = <18>;
|
| D | samsung,fimc.yaml | 183 samsung,csis-hs-settle = <12>;
|
| /Documentation/devicetree/bindings/iio/multiplexer/ |
| D | io-channel-mux.yaml | 43 settle-time-us:
46 Time required for analog signals to settle after muxing.
|
| /Documentation/devicetree/bindings/sound/ |
| D | adi,adau7002.yaml | 26 Delay after power up needed for device to settle.
|
| D | cirrus,cs42l42.yaml | 117 HS bias time to settle. Value is in milliseconds.
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | brcm,iproc-touchscreen.txt | 21 the tsc waits to allow the voltage to settle after
|
| D | ti,ads7843.yaml | 91 ti,settle-delay-usec:
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-mux-gpio.yaml | 60 settle-time-us:
|
| /Documentation/devicetree/bindings/regulator/ |
| D | regulator.yaml | 80 the regulator needs a constant time to settle after voltage increases
86 the regulator needs a constant time to settle after voltage decreases
|
| D | ti-abb-regulator.txt | 21 to settle down(target time for SR2_WTCNT_VALUE).
|
| /Documentation/devicetree/bindings/mfd/ |
| D | qcom,spmi-pmic.yaml | 326 qcom,hw-settle-time = <200>;
342 qcom,hw-settle-time-us = <200>;
|
| /Documentation/scsi/ |
| D | BusLogic.rst | 490 The "BusSettleTime:" or "BST:" option specifies the Bus Settle Time in
491 seconds. The Bus Settle Time is the amount of time to wait between a Host
530 Devices on the second host adapter to 31, and the Bus Settle Time on the
|
| D | sym53c8xx_2.rst | 50 10.2.10 Settle delay
631 10.2.10 Settle delay
635 settle=n delay for n seconds
|
| D | ChangeLog.ncr53c8xx | 365 mode to settle. Delays used while resetting the controller
|
| D | ncr53c8xx.rst | 1065 settle time 10 seconds settle:10
1079 tags:0,sync:50,debug:0,burst:7,led:0,wide:1,settle:2,diff:0,irqm:0
1092 tags:32,sync:12,debug:0,burst:7,led:1,wide:1,settle:2,diff:0,irqm:0
|
| /Documentation/devicetree/bindings/pci/ |
| D | mvebu-pci.txt | 153 /* wait 20ms for device settle after reset deassertion */
|
| /Documentation/admin-guide/ |
| D | cgroup-v2.rst | 3118 settle it. Different controllers did different things.
|