Searched full:startup (Results 1 – 25 of 106) sorted by relevance
12345
| /Documentation/core-api/ |
| D | cpu_hotplug.rst | 155 CPUHP_OFFLINE to CPUHP_ONLINE. Each state has a startup and a teardown
158 When a CPU is onlined, the startup callbacks are invoked sequentially until
179 The startup callbacks in this section are invoked before the CPU is
187 The startup callbacks are used to setup resources which are required to
192 The startup callbacks are allowed to fail. If a callback fails, the CPU
203 The startup callbacks in this section are invoked on the hotplugged CPU
219 The startup callbacks in this section are invoked on the hotplugged CPU
236 [CPUHP_OFFLINE + 1]->startup() -> success
237 [CPUHP_OFFLINE + 2]->startup() -> success
238 [CPUHP_OFFLINE + 3] -> skipped because startup == NULL
[all …]
|
| /Documentation/translations/zh_CN/core-api/ |
| D | cpu_hotplug.rst | 221 [CPUHP_OFFLINE + 1]->startup() -> 成功
222 [CPUHP_OFFLINE + 2]->startup() -> 成功
225 [CPUHP_BRINGUP_CPU]->startup() -> 成功
227 [CPUHP_BRINGUP_CPU + 1]->startup() -> 成功
229 [CPUHP_AP_ONLINE]->startup() -> 成功
231 [CPUHP_AP_ONLINE + 1]->startup() -> 成功
233 [CPUHP_ONLINE - 1]->startup() -> 成功
257 [CPUHP_OFFLINE + 1]->startup() -> 成功
258 [CPUHP_OFFLINE + 2]->startup() -> 成功
261 [CPUHP_BRINGUP_CPU]->startup() -> 成功
[all …]
|
| /Documentation/devicetree/bindings/clock/ |
| D | clps711x-clock.txt | 6 - startup-frequency: Factory set CPU startup frequency in HZ.
18 startup-frequency = <73728000>;
|
| D | fsl,plldig.yaml | 32 of this PLL cannot be changed during runtime only at startup. Therefore,
|
| /Documentation/sound/soc/ |
| D | pops-clicks.rst | 22 components in a specific order. This order is different for startup and
26 Startup Order :- DAC --> Mixers --> Output PGA --> Digital Unmute
40 startup or shutdown.
43 Startup Order - Input PGA --> Mixers --> ADC
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | atmel,sama5d2-adc.yaml | 40 atmel,startup-time-ms:
41 description: Startup time expressed in ms, it depends on SoC.
73 - atmel,startup-time-ms
91 atmel,startup-time-ms = <4>;
|
| D | atmel,sama9260-adc.yaml | 40 atmel,adc-startup-time:
43 Startup Time of the ADC in microseconds as defined in the datasheet
97 - atmel,adc-startup-time
115 atmel,adc-startup-time = <40>;
|
| /Documentation/ABI/testing/ |
| D | sysfs-driver-input-axp-pek | 1 What: /sys/class/input/input(x)/device/startup
4 Description: Startup time in us. Board is powered on if the button is pressed
|
| /Documentation/admin-guide/nfs/ |
| D | nfsd-admin-interfaces.rst | 25 On startup, nfsd and lockd grace periods start. nfsd is shut down by a write of
28 Between startup and shutdown, the number of threads may be adjusted up
39 removal of listening sockets, and startup and shutdown of the server.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | fixed-regulator.yaml | 89 startup-delay-us:
90 description: startup time in microseconds
131 startup-delay-us = <70000>;
143 startup-delay-us = <70000>;
155 startup-delay-us = <70000>;
|
| D | gpio-regulator.yaml | 68 startup-delay-us:
69 description: startup time in microseconds
119 startup-delay-us = <100000>;
|
| /Documentation/devicetree/bindings/fpga/ |
| D | fpga-bridge.yaml | 18 0 if driver should disable bridge at startup
19 1 if driver should enable bridge at startup
|
| D | lattice-ice40-fpga-mgr.txt | 9 that unless the GPIO is held low during startup, the
|
| /Documentation/devicetree/bindings/remoteproc/ |
| D | qcom,msm8916-mss-pil.yaml | 60 - description: XO proxy clock (control handed over after startup)
71 - description: CX proxy power domain (control handed over after startup)
72 - description: MX proxy power domain (control handed over after startup)
73 - description: MSS proxy power domain (control handed over after startup)
85 description: PLL proxy supply (control handed over after startup)
|
| /Documentation/misc-devices/ |
| D | ad525x_dpot.rst | 8 work with the immediate resistance settings as well as update the saved startup
19 The eeprom files are used to program the startup value of the device.
|
| /Documentation/devicetree/bindings/iio/proximity/ |
| D | devantech-srf04.yaml | 64 startup-time-ms:
66 This is the startup time the device needs after a resume to be up and
|
| D | semtech,sx9310.yaml | 77 semtech,startup-sensor:
127 semtech,startup-sensor = <1>;
|
| D | ams,as3935.yaml | 42 Set the noise and watchdog threshold register on startup. This will
|
| /Documentation/fb/ |
| D | cirrusfb.rst | 41 Full support for startup video modes (modedb) will be integrated soon.
65 * Correctly set default startup video mode.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | rohm,bd9576-pmic.yaml | 36 the PMIC startup. If vout1-en is LOW during PMIC startup then the VOUT1
|
| /Documentation/devicetree/bindings/input/ |
| D | syna,rmi4.yaml | 48 syna,startup-delay-ms:
200 syna,startup-delay-ms: false
216 syna,startup-delay-ms = <100>;
|
| /Documentation/devicetree/bindings/soc/fsl/ |
| D | fsl,layerscape-dcfg.yaml | 16 startup.
|
| /Documentation/networking/dsa/ |
| D | lan9303.rst | 20 At startup the driver configures the device to provide two separate network
|
| /Documentation/scsi/ |
| D | dc395x.rst | 66 3 0x08 8 Send Start command on startup. (Not used)
81 2 0x04 4 Reset SCSI Bus on startup.
|
| /Documentation/devicetree/bindings/soc/cirrus/ |
| D | cirrus,ep9301-syscon.yaml | 16 the various bus and peripheral clocks and controls the system startup
|
12345