Searched full:steps (Results 1 – 25 of 238) sorted by relevance
12345678910
| /Documentation/devicetree/bindings/input/ |
| D | rotary-encoder.yaml | 28 rotary-encoder,steps:
32 Number of steps in a full turnaround of the
41 device, hence no steps need to be passed.
47 greater than the specified steps or smaller than 0. For absolute axis only.
49 rotary-encoder,steps-per-period:
54 Number of steps (stable states) per period.
64 description: the method used to encode steps.
72 This property is deprecated. Instead, a 'steps-per-period ' value should
73 be used, such as "rotary-encoder,steps-per-period = <2>".
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-frequency-admv1014 | 5 Read/write value for the digital attenuator gain (IF_I) with coarse steps.
11 Read/write value for the digital attenuator gain (IF_Q) with coarse steps.
17 Read/write value for the digital attenuator gain (IF_I) with fine steps.
23 Read/write value for the digital attenuator gain (IF_Q) with fine steps.
|
| D | sysfs-class-fpga-manager | 19 states. The fpga manager driver is walking through these steps
21 though some steps may get skipped. Valid FPGA states will vary
34 * write complete = Doing post programming steps
|
| D | sysfs-bus-iio-proximity-as3935 | 6 Get the current distance in meters of storm (1km steps)
|
| D | sysfs-bus-iio-impedance-analyzer-ad5933 | 21 Number of frequency points (steps) in the frequency sweep.
|
| D | sysfs-driver-bd9571mwv-regulator | 14 following steps must be followed exactly:
|
| /Documentation/devicetree/bindings/leds/backlight/ |
| D | pwm-backlight.yaml | 45 num-interpolated-steps:
47 Number of interpolated steps between each value of brightness-levels
54 num-interpolated-steps: [brightness-levels]
78 // Example using num-interpolation-steps:
84 num-interpolated-steps = <2048>;
|
| D | mediatek,mt6370-backlight.yaml | 16 capability with 2048 current steps (11 bits, only for MT6370/MT6371) or
17 16384 current steps (14 bits, only for MT6372) in exponential or linear
49 mediatek,bled-pwm-hys-input-th-steps:
55 resolution needs more than 64 steps.
|
| /Documentation/userspace-api/media/v4l/ |
| D | common.rst | 8 Programming a V4L2 device consists of these steps:
23 In practice most steps are optional and can be executed out of order. It
|
| D | v4l2-selection-flags.rst | 47 steps. If this flag is not given, the configuration is propagated
48 inside the subdevice to all further processing steps.
|
| D | ext-ctrls-fm-rx.rst | 39 must be configured with steps of 8 characters. The result is it must
53 steps of 32 or 64 characters. The result is it must always contain a
|
| D | vidioc-overlay.rst | 52 for the necessary steps.
|
| /Documentation/networking/device_drivers/ethernet/amd/ |
| D | pds_vfio_pci.rst | 20 The pds-vfio-pci device is enabled via multiple configuration steps and
24 Shown below are the steps to bind the driver to a VF and also to the
50 After performing the steps above, a file in /dev/vfio/<iommu_group>
|
| D | pds_vdpa.rst | 24 The ``pds_vdpa`` device is enabled via multiple configuration steps and
29 Example steps:
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | richtek,rt5033-charger.yaml | 36 to 600 mA. Between 150 mA and 300 mA in 50 mA steps, between 300 mA and
37 600 mA in 100 mA steps.
|
| /Documentation/arch/sparc/ |
| D | console.rst | 1 Steps for sending 'break' on sunhv console
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | ti,am3359-tsc.yaml | 27 description: The sequencer supports a total of 16 programmable steps. Each
30 X, 5 for Y and 2 for Z (always). This utilises 12 of the 16 software steps
|
| /Documentation/devicetree/bindings/mfd/ |
| D | richtek,rt5033.yaml | 32 voltage ranges from 1.2 V to 3.0 V in 0.1 V steps. BUCK voltage ranges
33 from 1.0 V to 3.0 V in 0.1 V steps.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | ltc3589.txt | 21 0.3625 V to 0.75 V in 12.5 mV steps. The output voltage thus ranges between
26 and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not
|
| /Documentation/hwmon/ |
| D | amc6821.rst | 75 0 degree C to 124 degree C in steps of
92 0 degree C to 124 degree C in steps
|
| /Documentation/driver-api/mei/ |
| D | hdcp.rst | 17 Once all the steps of HDCP2.2 negotiation are completed,
|
| /Documentation/filesystems/nfs/ |
| D | rpc-server-gss.rst | 87 steps.
90 locking into the legacy mechanisms, the above steps must be performed
|
| /Documentation/userspace-api/ |
| D | dcdbas.rst | 40 Systems management software must perform the following steps to execute
67 Dell OpenManage performs the following steps to execute a power cycle or
|
| /Documentation/devicetree/ |
| D | dynamic-resolution-notes.rst | 17 In sequence the resolver works by the following steps:
|
| /Documentation/userspace-api/media/rc/ |
| D | lirc-get-rec-resolution.rst | 36 signals can only be reported in 50 microsecond steps.
|
12345678910