Searched full:stops (Results 1 – 25 of 96) sorted by relevance
1234
| /Documentation/hwmon/ |
| D | g762.rst | 59 integer value between 0 and 255. 0 stops the fan, 255 makes
65 entry (0 stops the fan, 255 makes it run at full speed). In closed-loop mode
|
| D | amc6821.rst | 71 which is rw. Below this temperature fan stops.
87 Below this temperature the fan stops in
|
| D | g760a.rst | 26 Setting a period of 0 stops the fan; setting the period to 255 sets
|
| D | thmc50.rst | 86 so it stops fans even if the value 0 into the ANALOG_OUT register does not.
|
| /Documentation/ABI/testing/ |
| D | gpio-cdev | 25 Stops and free up the I/O contexts that was associated
|
| D | sysfs-bus-intel_th-devices-msc | 51 Description: (RW) Configure whether trace stops when the last available window
|
| D | sysfs-mce | 49 stops finding MCEs, it triggers an exponential backoff
|
| D | debugfs-driver-qat | 92 After writing this file, the driver stops arbitration on a
|
| /Documentation/core-api/ |
| D | memory-hotplug.rst | 81 MEM_ONLINE, or MEM_OFFLINE action to cancel hotplugging. It stops
84 NOTIFY_STOP stops further processing of the notification queue.
|
| /Documentation/driver-api/thermal/ |
| D | x86_pkg_temperature_thermal.rst | 47 Setting 0, stops sending thermal notifications.
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | maxim,max14577.yaml | 49 asserts and charging stops.
|
| /Documentation/driver-api/media/drivers/ |
| D | pxa_camera.rst | 33 Once the last buffer is filled in, the QCI interface stops.
154 - DMA controller finishes Videobuffer2, and DMA stops
191 If DMA stops just after pxa_camera_check_link_miss() reads DDADR()
|
| /Documentation/networking/device_drivers/atm/ |
| D | cxacru.rst | 109 - "restart" (stops, waits 1.5s, then starts)
|
| /Documentation/filesystems/ |
| D | quota.rst | 70 - four warnings are also defined for the event when user stops
|
| /Documentation/networking/ |
| D | netif-msg.rst | 28 - 3 Interface starts and stops, including normal status messages
|
| /Documentation/devicetree/bindings/watchdog/ |
| D | atmel,at91sam9-wdt.yaml | 79 if the CPU stops working while it is in idle state, which is probably
|
| /Documentation/userspace-api/media/drivers/ |
| D | imx-uapi.rst | 44 and remain at that value until rolling stops.
|
| /Documentation/sphinx/ |
| D | kernel_abi.py | 116 # Sphinx parser is lazy: it stops parsing contents in the
|
| /Documentation/input/ |
| D | ff.rst | 150 stops the effect if it was playing.
232 case, the driver stops the effect, up-load it, and restart it.
|
| /Documentation/i2c/ |
| D | i2c-address-translators.rst | 77 - ATR chip stops clock stretching and forwards reply on bus A,
|
| /Documentation/leds/ |
| D | leds-class.rst | 125 it is guaranteed not to sleep, passing LED_OFF stops
131 device registers and can sleep, passing LED_OFF stops hardware
|
| /Documentation/userspace-api/media/v4l/ |
| D | func-read.rst | 75 A driver discarding the newest frames stops capturing until the next
|
| /Documentation/driver-api/media/ |
| D | tx-rx.rst | 129 A transmitter stops sending the stream of images as a result of
|
| /Documentation/input/devices/ |
| D | atarikbd.rst | 152 command in this mode not only stop the output but also temporarily stops
163 only stops the output but also temporarily stops scanning the button (samples
449 MONITORING mode, the PAUSE OUTPUT command also temporarily stops the
|
| /Documentation/locking/ |
| D | locktorture.rst | 14 and stops when the module is unloaded. This program is based on how RCU
|
1234