Searched full:strobe (Results 1 – 25 of 35) sorted by relevance
12
| /Documentation/userspace-api/media/v4l/ |
| D | ext-ctrls-flash.rst | 23 Unsynchronised LED flash (software strobe)
34 Synchronised LED flash (hardware strobe)
38 timeout) but controlled by the sensor through a strobe signal from the
84 Defines the source of the flash LED strobe.
93 - The flash strobe is triggered by using the
96 - The flash strobe is triggered by an external source. Typically
98 flash strobe start to exposure start.
103 Strobe flash. Valid when V4L2_CID_FLASH_LED_MODE is set to
110 Stop flash strobe immediately.
113 Strobe status: whether the flash is strobing at the moment or not.
[all …]
|
| /Documentation/devicetree/bindings/memory-controllers/ |
| D | ti-aemif.txt | 84 - ti,cs-select-strobe-mode: enable/disable select strobe mode
85 In select strobe mode chip select behaves as
86 the strobe and is active only during the strobe
92 device wants to extend the strobe period. If
104 and the activation of read strobe.
107 - ti,cs-read-strobe-ns: read strobe width, ns
109 the read strobe.
114 strobe and the end of the cycle (which may be
121 and the activation of write strobe.
124 - ti,cs-write-strobe-ns: write strobe width, ns
[all …]
|
| D | intel,ixp4xx-expansion-peripheral-props.yaml | 29 description: Strobe timing, extend strobe phase with n cycles.
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-led-flash | 6 Set the brightness of this LED in the flash strobe mode, in
18 Maximum brightness level for this LED in the flash strobe mode,
26 Hardware timeout for flash, in microseconds. The flash strobe
28 of the strobe. The file is created only for the flash LED
43 Flash strobe state. When written with 1 it triggers flash strobe
62 the flash strobe was still on when
|
| D | sysfs-bus-intel_th-devices-pti | 12 Description: (RW) 0: PTI trace clock acts as a strobe which only toggles
|
| /Documentation/devicetree/bindings/regulator/ |
| D | richtek,rtmv20-regulator.yaml | 16 There're still four pins for camera control, two inputs (strobe and vsync),
17 the others for outputs (fsin1 and fsin2). Strobe input to start the current
38 load current pulse delay in microsecond after strobe pin pulse high.
45 Load current pulse width in microsecond after strobe pin pulse high.
100 richtek,strobe-polarity-high:
101 description: Strobe pin active polarity control.
150 richtek,strobe-polarity-high;
|
| /Documentation/devicetree/bindings/phy/ |
| D | rockchip,rk3399-emmc-phy.yaml | 32 rockchip,enable-strobe-pulldown:
35 Enable internal pull-down for the strobe
|
| /Documentation/leds/ |
| D | leds-class-flash.rst | 49 defines the source of the flash LED strobe -
52 strobe start with exposure start,
74 determines whether the flash strobe source
|
| D | leds-lm3556.rst | 24 or by pulling the STROBE pin HIGH.
28 * if STROBE pin is enabled, below example control brightness only, and
29 ON / OFF will be controlled by STROBE pin.
|
| /Documentation/devicetree/bindings/bus/ |
| D | ts-nbus.txt | 14 - ts,strobe-gpios : The GPIO pin connected to the stobe line on the FPGA
41 ts,strobe-gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/leds/ |
| D | skyworks,aat1290.yaml | 15 asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
16 respectively. In order to add a capability of selecting the strobe signal
|
| D | mediatek,mt6370-flashlight.yaml | 14 Add MT6370 flash LED driver include 2-channel flash LED support Torch/Strobe Mode.
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | ovti,og01a1b.yaml | 36 strobe-gpios:
37 description: Input GPIO connected to strobe pad of the sensor.
|
| D | st,st-vgxy61.yaml | 51 st,strobe-gpios-polarity:
53 Invert polarity of illuminator's lights strobe GPIOs.
|
| D | ti,ds90ub960.yaml | 57 ti,manual-strobe:
60 Enable manual strobe position and EQ level
99 ti,strobe-pos:
103 description: Manual strobe position
|
| /Documentation/devicetree/bindings/mmc/ |
| D | fsl-imx-esdhc.yaml | 148 fsl,strobe-dll-delay-target:
151 Specify the strobe dll control slave delay target.
153 property allows user to change the delay target for the strobe input read clock.
|
| D | samsung,exynos-dw-mshc.yaml | 106 samsung,read-strobe-delay:
109 RCLK (Data strobe) delay to control HS400 mode (Latency value for delay
|
| D | brcm,sdhci-brcmstb.yaml | 110 mmc-hs400-enhanced-strobe;
|
| D | sdhci-am654.yaml | 189 ti,strobe-sel:
190 description: strobe select delay for HS400 speed mode.
|
| D | sprd,sdhci-r11.yaml | 99 mmc-hs400-enhanced-strobe;
|
| D | cdns,sdhci.yaml | 108 cdns,phy-dll-delay-strobe:
|
| /Documentation/devicetree/bindings/rtc/ |
| D | microchip,mfps-rtc.yaml | 39 strobe (typically 1 Hz) for the calendar counter. By default, the rtc
|
| /Documentation/devicetree/bindings/usb/ |
| D | chipidea,usb2-common.yaml | 141 strobe pin and the "active" state needs to pull up the strobe pin.
|
| /Documentation/networking/ |
| D | plip.rst | 134 strobe) input, arranged so that the data input bits appear as contiguous
141 STROBE output 1*
172 STROBE->BUSY 1 - 11
|
| /Documentation/devicetree/bindings/media/ |
| D | video-interfaces.yaml | 213 strobe:
217 Whether the clock signal is used as clock (0) or strobe (1). Used with
|
12