Searched full:termination (Results 1 – 25 of 45) sorted by relevance
12
| /Documentation/ABI/testing/ |
| D | sysfs-class-net-janz-ican3 | 1 What: /sys/class/net/<iface>/termination
6 Value representing the can bus termination
8 Default: 1 (termination active)
9 Reading: get actual termination state
10 Writing: set actual termination state (0=no termination, 1=termination active)
|
| D | sysfs-firmware-dmi-entries | 64 terminated strings, with termination signalled
|
| /Documentation/devicetree/bindings/net/can/ |
| D | can-controller.yaml | 16 termination-gpios:
17 description: GPIO pin to enable CAN bus termination.
20 termination-ohms:
21 description: The resistance value of the CAN bus termination resistor.
|
| D | fsl,flexcan.yaml | 131 termination-gpios: true
132 termination-ohms: true
174 termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
175 termination-ohms = <120>;
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | adi,ad7280a.yaml | 47 adi,thermistor-termination:
50 Enable the thermistor termination function.
73 adi,thermistor-termination;
|
| /Documentation/devicetree/bindings/phy/ |
| D | xlnx,zynqmp-psgtr.yaml | 69 xlnx,tx-termination-fix:
71 Include this for fixing functional issue with the TX termination
89 xlnx,tx-termination-fix: false
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | bq24257.yaml | 37 ti,termination-current:
79 - ti,termination-current
101 ti,termination-current = <50000>;
119 ti,termination-current = <50000>;
|
| D | bq2415x.yaml | 52 ti,termination-current:
73 - ti,termination-current
92 ti,termination-current = <100>;
|
| D | bq25890.yaml | 42 ti,termination-current:
94 - ti,termination-current
118 ti,termination-current = <50000>;
|
| D | sc2731-charger.yaml | 29 - charge-term-current-microamp: current for charge termination phase.
|
| D | richtek,rt9467.yaml | 17 regulation, and charge termination. The charge current is regulated through
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | analogix,anx7625.yaml | 64 [R Termination control] setting.
68 Registers 10~19, bit 5:6 is [R termination control], these bits
69 adjust 50ohm impedance of DP tx termination. 00:55 ohm,
|
| /Documentation/scsi/ |
| D | qlogicfas.rst | 68 The best way to test if your cables, termination, etc. are good is to
82 termination (the ACK can be reflected), or by noise when the chips
|
| /Documentation/filesystems/ |
| D | netfs_library.rst | 500 With a termination handler function pointer::
544 Also provided is a pointer to a termination handler function and private
545 data to pass to that function. The termination function should be called
547 indicating whether the termination is definitely happening in the caller's
566 Also provided is a pointer to a termination handler function and private
567 data to pass to that function. The termination function should be called
569 indicating whether the termination is definitely happening in the caller's
|
| /Documentation/devicetree/bindings/serial/ |
| D | rs485.yaml | 54 description: GPIO pin to enable RS485 bus termination.
|
| /Documentation/driver-api/dmaengine/ |
| D | client.rst | 369 5. Synchronize termination API
375 Synchronize the termination of the DMA channel to the current context.
378 the termination of the DMA channel to the current context. The function will
|
| /Documentation/devicetree/bindings/pci/ |
| D | xgene-pci-msi.txt | 9 registers. These registers include the MSI termination address and data
|
| /Documentation/virt/geniezone/ |
| D | introduction.rst | 80 before termination.
|
| /Documentation/core-api/ |
| D | netlink.rst | 84 Accept strings without the null-termination (for legacy families only).
|
| /Documentation/networking/device_drivers/can/ |
| D | can327.rst | 323 A note on CAN bus termination
331 termination resistors on its PCB and try removing them.
|
| /Documentation/process/ |
| D | kernel-enforcement-statement.rst | 20 Notwithstanding the termination provisions of the GPL-2.0, we agree that
|
| /Documentation/filesystems/caching/ |
| D | netfs-api.rst | 270 The read and write functions can be given an optional termination function that
277 If a termination function is given, the operation will be run asynchronously
278 and the termination function will be called upon completion. If not given, the
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | ti,sci-inta.yaml | 17 which handles the termination of system events to that they can
|
| /Documentation/locking/ |
| D | locktorture.rst | 82 zero, which disables test termination and system shutdown.
|
| /Documentation/arch/riscv/ |
| D | vector.rst | 41 instructions under such condition will trap and casuse the termination of the thread.
|
12