Searched full:voltages (Results 1 – 25 of 105) sorted by relevance
12345
| /Documentation/userspace-api/media/dvb/ |
| D | fe-enable-high-lnb-voltage.rst | 13 …E_HIGH_LNB_VOLTAGE - Select output DC level between normal LNBf voltages or higher LNBf - voltages.
33 - >0 - enables slightly higher voltages instead of 13/18V, in order
39 Select output DC level between normal LNBf voltages or higher LNBf
40 voltages between 0 (normal) or a value grater than 0 for higher
41 voltages.
|
| /Documentation/hwmon/ |
| D | max16065.rst | 54 monitor and sequence multiple system voltages. The MAX16065/MAX16066 can also
56 current-sense amplifier. The MAX16065 manages up to twelve system voltages
57 simultaneously, and the MAX16066 manages up to eight supply voltages.
60 system voltages. The MAX16067 manages up to six system voltages simultaneously.
63 system voltages simultaneously.
66 system voltages. The MAX16070/MAX16071 can also accurately monitor (+/-2.5%)
68 MAX16070 monitors up to twelve system voltages simultaneously, and the MAX16071
69 monitors up to eight supply voltages.
|
| D | da9055.rst | 19 different inputs. The track and hold circuit ensures stable input voltages at
31 chip junction temperature and auxiliary channels voltages.
36 Voltages are sampled in a AUTO mode it can be manually sampled too and results
43 The voltages on ADC channels 1, 2 and 3 are calculated as:
|
| D | wm831x.rst | 21 monitor a range of system operating parameters, including the voltages
28 Voltages are sampled by a 12 bit ADC. Voltages in millivolts are 1.465
|
| D | ftsteutates.rst | 21 enhancements. It can monitor up to 4 voltages, 16 temperatures and
30 The 4 voltages require a board-specific multiplier, since the BMC can
31 only measure voltages up to 3.3V and thus relies on voltage dividers.
|
| D | wm8350.rst | 22 monitor a range of system operating parameters, including the voltages
29 Voltages are sampled by a 12 bit ADC. For the internal supplies the ADC
|
| D | emc6w201.rst | 25 voltages (including its own VCC) and five external thermal sensors,
35 The driver currently only supports the monitoring of the voltages,
|
| D | powr1220.rst | 23 for output voltages and GPIOs. This driver implements the voltage
26 Voltages are sampled by a 12-bit ADC with a step size of 2 mV.
|
| D | ltc2991.rst | 27 The LTC2991 is used to monitor system temperatures, voltages and currents.
29 supply voltages and can be paired for differential measurements of current sense
|
| D | ltc2992.rst | 23 the input voltages and four auxiliary external voltages.
|
| D | smsc47m192.rst | 42 Voltages and temperatures are measured by an 8-bit ADC, the resolution
44 Voltages are scaled such that the nominal voltage corresponds to
49 show voltages in mV and temperatures in units of 0.001 degC.
80 All voltages are read and written in mV.
|
| D | gl518sm.rst | 36 0x80 chips support the reading of all voltages and revision 0x00 only
62 measures voltages between 0.000 and 5.865 volt, with a resolution of 0.023
63 volt. The other inputs measure voltages between 0.000 and 4.845 volt, with
|
| D | da9052.rst | 20 different inputs. The track and hold circuit ensures stable input voltages at
46 Voltages are sampled by a 10 bit ADC.
56 The voltages on ADC channels 4, 5 and 6 are calculated as:
|
| D | bcm54140.rst | 18 its die temperature as well as two analog voltages.
21 Both voltages and the temperature are measured in a round-robin fashion.
|
| D | pc87427.rst | 24 monitoring capabilities. It can monitor up to 18 voltages, 8 fans and
26 the moment, voltages aren't.
|
| D | adp1050.rst | 29 conversion used to monitor system temperatures, voltages and currents.
30 Through the PMBus interface, the device can monitor input/output voltages,
|
| D | lm78.rst | 39 which is used to report the lower voltages newer Pentium processors use.
64 inputs can measure voltages between 0 and 4.08 volts, with a resolution
|
| /Documentation/devicetree/bindings/phy/ |
| D | transmit-amplitude.yaml | 19 Transmit amplitude voltages in microvolts, peak-to-peak. If this property
26 Names of the modes corresponding to voltages in the 'tx-p2p-microvolt'
27 property. Required only if multiple voltages are provided.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd71815-regulator.yaml | 92 # Bucks 1 and 2 support giving separate voltages for operational states
96 # buck voltages to not be toggled by HW state. Enable status may still
109 # that setting non zero voltages for bucks 1/2 will also enable voltage
|
| D | nvidia,tegra-regulators-coupling.txt | 12 The CORE and RTC voltages shall be in a range of 170mV from each other
19 and CPU voltages shall be in a range of 300mV from each other and CORE
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | adi,ltc2991.yaml | 14 The LTC2991 is used to monitor system temperatures, voltages and currents.
16 supply voltages and can be paired for differential measurements of current
|
| /Documentation/devicetree/bindings/opp/ |
| D | ti,omap-opp-supply.yaml | 37 - description: OMAP5+ optimized voltages in efuse(Class 0) VDD along with
40 - description: OMAP5+ optimized voltages in efuse(class0) VDD but no VBB
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-iio-thermocouple | 6 is protected from excessive voltages applied to the thermocouple
|
| /Documentation/driver-api/ |
| D | regulator.rst | 99 interface for this. Both take ranges of voltages and currents, supporting
101 normally permits the CPU to use a wider range of supply voltages at lower
143 a given system, for example supporting higher supply voltages than the
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | mediatek,mt6359-auxadc.yaml | 17 other than voltages for various PMIC internal components.
|
12345