Home
last modified time | relevance | path

Searched +full:wait +full:- +full:pin (Results 1 – 25 of 38) sorted by relevance

12

/Documentation/devicetree/bindings/memory-controllers/
Dti,gpmc-child.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Tony Lindgren <tony@atomide.com>
11 - Roger Quadros <rogerq@kernel.org>
24 gpmc,sync-clk-ps:
28 # Chip-select signal timings corresponding to GPMC_CONFIG2:
29 gpmc,cs-on-ns:
33 gpmc,cs-rd-off-ns:
[all …]
Dti,gpmc.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Tony Lindgren <tony@atomide.com>
11 - Roger Quadros <rogerq@kernel.org>
16 - Asynchronous SRAM-like memories and ASICs
17 - Asynchronous, synchronous, and page mode burst NOR flash
18 - NAND flash
19 - Pseudo-SRAM devices
[all …]
Dti-aemif.txt4 provide a glue-less interface to a variety of asynchronous memory devices like
11 Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
12 OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
13 Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
17 - compatible: "ti,davinci-aemif"
18 "ti,keystone-aemif"
19 "ti,da850-aemif"
21 - reg: contains offset/length value for AEMIF control registers
24 - #address-cells: Must be 2. The partition number has to be encoded in the
25 first address cell and it may accept values 0..N-1
[all …]
/Documentation/devicetree/bindings/pinctrl/
Dlantiq,pinctrl-xway.txt4 - compatible: "lantiq,<chip>-pinctrl", where <chip> is:
10 - reg: Should contain the physical address and length of the gpio/pinmux
13 Please refer to pinctrl-bindings.txt in this directory for details of the
15 phrase "pin configuration node".
17 Lantiq's pin configuration nodes act as a container for an arbitrary number of
19 pin, a group, or a list of pins or groups. This configuration can include the
20 mux function to select on those group(s), and two pin configuration parameters:
21 pull-up and open-drain
27 other words, a subnode that lists a mux function but no pin configuration
28 parameters implies no information about any pin configuration parameters.
[all …]
/Documentation/devicetree/bindings/power/reset/
Dgpio-restart.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/power/reset/gpio-restart.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
17 'open-source' is not found, the GPIO line will be driven in the inactive state. Otherwise its
22 This will also cause an inactive->active edge condition, triggering positive edge triggered
23 reset. After a delay specified by active-delay, the GPIO is set to inactive, thus causing an
24 active->inactive edge, triggering negative edge triggered reset. After a delay specified by
25 inactive-delay, the GPIO is driven active again. After a delay specified by wait-delay, the
[all …]
/Documentation/devicetree/bindings/input/touchscreen/
Dtsc2007.txt4 - compatible: must be "ti,tsc2007".
5 - reg: I2C address of the chip.
6 - ti,x-plate-ohms: X-plate resistance in ohms.
9 - gpios: the interrupt gpio the chip is connected to (through the penirq pin).
10 The penirq pin goes to low when the panel is touched.
12 - interrupts: (gpio) interrupt to which the chip is connected
14 - ti,max-rt: maximum pressure.
15 - ti,fuzzx: specifies the absolute input fuzz x value.
16 If set, it will permit noise in the data up to +- the value given to the fuzz
18 - ti,fuzzy: specifies the absolute input fuzz y value.
[all …]
Dazoteq,iqs7211.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jeff LaBundy <jeff@labundy.com>
13 The Azoteq IQS7210A, IQS7211A and IQS7211E trackpad and touchscreen control-
14 lers employ projected-capacitance sensing and can track two contacts.
21 - azoteq,iqs7210a
22 - azoteq,iqs7211a
23 - azoteq,iqs7211e
28 irq-gpios:
[all …]
/Documentation/devicetree/bindings/sound/
Dcirrus,cs42l42.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - patches@opensource.cirrus.com
13 The CS42L42 is a low-power audio codec designed for portable applications.
14 It provides a high-dynamic range, stereo DAC for audio playback and a mono
15 high-dynamic-range ADC for audio capture. There is an integrated headset
21 - cirrus,cs42l42
22 - cirrus,cs42l83
29 VP-supply:
[all …]
Dst,sta350.txt7 - compatible: "st,sta350"
8 - reg: the I2C address of the device for I2C
9 - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
12 - power-down-gpios: a GPIO spec for the power down pin. If specified,
16 - vdd-dig-supply: regulator spec, providing 3.3V
17 - vdd-pll-supply: regulator spec, providing 3.3V
18 - vcc-supply: regulator spec, providing 5V - 26V
22 - st,output-conf: number, Selects the output configuration:
23 0: 2-channel (full-bridge) power, 2-channel data-out
24 1: 2 (half-bridge). 1 (full-bridge) on-board power
[all …]
Dcs35l36.txt5 - compatible : "cirrus,cs35l36"
7 - reg : the I2C address of the device for I2C
9 - VA-supply, VP-supply : power supplies for the device,
13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
32 - cirrus,multi-amp-mode : Boolean to determine if there are more than
33 one amplifier in the system. If more than one it is best to Hi-Z the ASP
36 - cirrus,boost-ctl-select : Boost converter control source selection.
39 0x00 - Control Port Value
[all …]
/Documentation/ABI/testing/
Dsysfs-bus-iio-adc-envelope-detector8 of a comparator wired to an interrupt pin. Like so::
12 input +------>-------|+ \
14 .-------. | }---.
16 | dac|-->--|- / |
20 | irq|------<-------'
22 '-------'
37 Number of milliseconds to wait for the comparator in each
/Documentation/userspace-api/media/cec/
Dcec-ioc-receive.rst1 .. SPDX-License-Identifier: GFDL-1.1-no-invariants-or-later
14 CEC_RECEIVE, CEC_TRANSMIT - Receive or transmit a CEC message
42 If the file descriptor is in non-blocking mode and there are no received
43 messages pending, then it will return -1 and set errno to the ``EAGAIN``
45 is non-zero and no message arrived within ``timeout`` milliseconds, then
46 it will return -1 and set errno to the ``ETIMEDOUT`` error code.
51 be 0, ``tx_status`` will be 0 and ``rx_status`` will be non-zero).
52 2. the transmit result of an earlier non-blocking transmit (the ``sequence``
53 field will be non-zero, ``tx_status`` will be non-zero and ``rx_status``
55 3. the reply to an earlier non-blocking transmit (the ``sequence`` field will
[all …]
/Documentation/driver-api/media/
Dcec-core.rst1 .. SPDX-License-Identifier: GPL-2.0
15 ----------------
33 ---------------------
53 will be stored in adap->priv and can be used by the adapter ops.
95 Implementing the Low-Level CEC Adapter
96 --------------------------------------
98 The following low-level adapter operations have to be implemented in
103 .. code-block:: none
107 /* Low-level callbacks */
123 /* High-level callback */
[all …]
/Documentation/filesystems/xfs/
Dxfs-delayed-logging-design.rst1 .. SPDX-License-Identifier: GPL-2.0
33 details logged are made up of the changes to in-core structures rather than
34 on-disk structures. Other objects - typically buffers - have their physical
64 place. This means that permanent transactions can be used for one-shot
65 modifications, but one-shot reservations cannot be used for permanent
68 In the code, a one-shot transaction pattern looks somewhat like this::
97 While this might look similar to a one-shot transaction, there is an important
123 the on-disk journal.
142 in the journal and wait for that to complete.
165 transaction, we have to reserve enough space to record a full leaf-to-root split
[all …]
/Documentation/devicetree/bindings/hwmon/
Dadi,ltc4282.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Nuno Sa <nuno.sa@analog.com>
15 https://www.analog.com/media/en/technical-documentation/data-sheets/ltc4282.pdf
20 - adi,ltc4282
25 vdd-supply: true
30 '#clock-cells':
33 adi,rsense-nano-ohms:
36 adi,vin-mode-microvolt:
[all …]
/Documentation/dev-tools/
Dgpio-sloppy-logic-analyzer.rst1 .. SPDX-License-Identifier: GPL-2.0
12 This document briefly describes how to run the GPIO based in-kernel sloppy
22 Another feature is to snoop on on-chip peripherals if the I/O cells of these
25 I2C traffic without any wiring (if your hardware supports it). In the pin
26 control subsystem such pin controllers are called "non-strict": a certain pin
31 non-deterministic code paths and non-maskable interrupts. It is called 'sloppy'
47 i2c-analyzer {
48 compatible = "gpio-sloppy-logic-analyzer";
49 probe-gpios = <&gpio6 21 GPIO_OPEN_DRAIN>, <&gpio6 4 GPIO_OPEN_DRAIN>;
50 probe-names = "SCL", "SDA";
[all …]
/Documentation/devicetree/bindings/connector/
Dusb-connector.yaml1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/connector/usb-connector.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Rob Herring <robh@kernel.org>
20 - enum:
21 - usb-a-connector
22 - usb-b-connector
23 - usb-c-connector
25 - items:
[all …]
/Documentation/filesystems/caching/
Dbackend-api.rst1 .. SPDX-License-Identifier: GPL-2.0
7 The FS-Cache system provides an API by which actual caches can be supplied to
8 FS-Cache for it to then serve out to network filesystems and other interested
11 #include <linux/fscache-cache.h>.
29 pin the cache during access in addition to acting as reference points for the
34 The cache backend and the network filesystem can both ask for cache cookies -
102 This moves the cache to the withdrawn state to prevent new cache- and
103 volume-level accesses from starting and then waits for outstanding cache-level
113 wait for completion by calling::
152 * ``cache`` - The parent cache cookie.
[all …]
/Documentation/gpu/
Ddrm-vm-bind-async.rst1 .. SPDX-License-Identifier: (GPL-2.0+ OR MIT)
10 * ``VRAM``: On-device memory. Sometimes referred to as device local memory.
16 an IOCTL. The operations include mapping and unmapping system- or
20 synchronization objects can be either generic, like dma-fences or
24 * ``in-syncobj``: Argument to a VM_BIND IOCTL, the VM_BIND operation waits
27 * ``out-syncobj``: Argument to a VM_BIND_IOCTL, the VM_BIND operation
30 * ``dma-fence``: A cross-driver synchronization object. A basic
31 understanding of dma-fences is required to digest this
33 :doc:`dma-buf doc </driver-api/dma-buf>`.
35 * ``memory fence``: A synchronization object, different from a dma-fence.
[all …]
/Documentation/devicetree/bindings/input/
Diqs269a.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jeff LaBundy <jeff@labundy.com>
13 - $ref: input.yaml#
16 The Azoteq IQS269A is an 8-channel capacitive touch controller that features
17 additional Hall-effect and inductive sensing capabilities.
24 - azoteq,iqs269a
25 - azoteq,iqs269a-00
26 - azoteq,iqs269a-d0
[all …]
/Documentation/networking/
Dnapi.rst1 .. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
30 of the NAPI instance while the method is the driver-specific event
37 -----------
55 ------------
64 argument - drivers can process completions for any number of Tx
95 not call napi_complete_done() and wait to be called again,
96 or return ``budget - 1``.
101 -------------
109 As mentioned in the :ref:`drv_ctrl` section - napi_disable() and subsequent
110 calls to the poll method only wait for the ownership of the instance
[all …]
/Documentation/i2c/
Dslave-testunit-backend.rst1 .. SPDX-License-Identifier: GPL-2.0
7 by Wolfram Sang <wsa@sang-engineering.com> in 2020
11 easy to obtain). Examples include multi-master testing, and SMBus Host Notify
21 # echo "slave-testunit 0x1030" > /sys/bus/i2c/devices/i2c-0/new_device
30 compatible = "slave-testunit";
39 When writing, the device consists of 4 8-bit registers and, except for some
43 .. csv-table::
51 Using 'i2cset' from the i2c-tools package, the generic command looks like::
53 # i2cset -y <bus_num> <testunit_address> <CMD> <DATAL> <DATAH> <DELAY> i
57 acknowledged. You need to wait until the old one is completed.
[all …]
/Documentation/devicetree/bindings/phy/
Dti,phy-j721e-wiz.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 # Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
4 ---
5 $id: http://devicetree.org/schemas/phy/ti,phy-j721e-wiz.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Kishon Vijay Abraham I <kishon@ti.com>
16 - ti,j721e-wiz-16g
17 - ti,j721e-wiz-10g
18 - ti,j721s2-wiz-10g
19 - ti,am64-wiz-10g
[all …]
/Documentation/networking/device_drivers/hamradio/
Dz8530drv.rst1 .. SPDX-License-Identifier: GPL-2.0
5 SCC.C - Linux driver for Z8530 based HDLC cards for AX.25
14 1. ftp://ftp.ccac.rwth-aachen.de/pub/jr/z8530drv-utils_3.0-3.tar.gz
16 2. ftp://ftp.pspt.fi/pub/ham/linux/ax25/z8530drv-utils_3.0-3.tar.gz
41 AX.25-HOWTO on how to emulate a KISS TNC on network device drivers.
54 please read 'man insmod' that comes with module-init-tools.
64 of your rc.*-files. This has to be done BEFORE you can
92 - this is just a delimiter to make sccinit a bit simpler to
96 - the address of the data port A of this Z8530 (needed)
98 - the address of the control port A (needed)
[all …]
/Documentation/devicetree/bindings/net/wireless/
Dqcom,ath10k.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Kalle Valo <kvalo@kernel.org>
11 - Jeff Johnson <jjohnson@kernel.org>
19 - qcom,ath10k # SDIO-based devices
20 - qcom,ipq4019-wifi
21 - qcom,wcn3990-wifi # SNoC-based devices
26 reg-names:
28 - const: membase
[all …]

12