Searched full:works (Results 1 – 25 of 462) sorted by relevance
12345678910>>...19
| /Documentation/power/ |
| D | video.rst | 32 Currently, VBE_SAVE method (6 below) works on most
40 There are a few types of systems where video works after S3 resume:
50 the BIOS works well enough to be able to set video mode. Use
68 POSTing bios works. Ole Rohne has patch to do just that at
83 You may have a system where none of above works. At that point you
84 either invent another ugly hack that works, or write proper driver for
112 Asus L2400D s3_mode (3) [#f2]_ (S1 also works OK)
114 Asus L3800C (Radeon M7) s3_bios (2) (S1 also works OK)
119 Compaq Armada E500 - P3-700 none (1) (S1 also works OK)
143 HP Omnibook 5150 none (1), (S1 also works OK)
[all …]
|
| D | basic-pm-debugging.rst | 10 To check if hibernation works, you can try to hibernate in the "reboot" mode::
41 If neither "platform" nor "shutdown" hibernation mode works, you will need to
145 see if that works.
193 works every time, but resume from actual hibernation does not work or is
220 To verify that the STR works, it is generally more convenient to use the s2ram
|
| /Documentation/admin-guide/media/ |
| D | cx88.rst | 15 - Works.
19 - Works. The TV standard detection is made by the driver, as the
25 - Works.
|
| D | cafe_ccic.rst | 15 Current status: the core driver works. It can generate data in YUV422,
28 The "xawtv" utility also works; gqcam does not, for unknown reasons.
|
| /Documentation/devicetree/bindings/rtc/ |
| D | epson,rx6110.txt | 28 - spi-cpha: RX6110 works with SPI shifted clock phase
29 - spi-cpol: RX6110 works with SPI inverse clock polarity
|
| D | rtc-mt6397.txt | 3 MediaTek PMIC based RTC is an independent function of MediaTek PMIC that works
|
| /Documentation/devicetree/ |
| D | dynamic-resolution-notes.rst | 10 How the resolver works
17 In sequence the resolver works by the following steps:
|
| /Documentation/scsi/ |
| D | qlogicfas.rst | 8 only works with the ISA, VLB, and PCMCIA versions of the Qlogic
27 This currently only works if the card is enabled first from DOS. This
59 Make sure it works properly under DOS. You should also do an initial FDISK
|
| /Documentation/input/devices/ |
| D | cs461x.rst | 13 Raw mode works fine with analog joystick front-end driver and cs461x
28 The driver works with ALSA drivers simultaneously. For example, the xracer
|
| /Documentation/hwmon/ |
| D | thmc50.rst | 60 The ADM1022 works the same as THMC50 but it is faster (5 Hz instead of
88 The driver was tested on Compaq AP550 with two ADM1022 chips (one works
|
| /Documentation/ |
| D | Kconfig | 10 warning when something is missing. Works only if the Kernel
|
| /Documentation/ABI/removed/ |
| D | raw1394 | 15 libraw1394 (works with firewire-cdev too, transparent to library ABI
|
| D | video1394 | 16 libdc1394 (works with firewire-cdev too, transparent to library ABI
|
| /Documentation/userspace-api/ |
| D | futex2.rst | 43 the upper bits are zeroed. ``uintptr_t`` does the tricky and it works for
81 properly enqueued. This is the default behavior, and it works with both private
|
| /Documentation/process/ |
| D | index.rst | 14 to learn about how our community works. Reading these documents will make
18 An introduction to how kernel development works
|
| D | development-process.rst | 8 an attempt to document how this community works in a way which is
|
| /Documentation/networking/ |
| D | netfilter-sysctl.rst | 16 kernel log. If enabled, this target also works in other network
|
| /Documentation/ABI/stable/ |
| D | firewire-cdev | 95 Isochronous reception works in packet-per-buffer fashion except
96 for multichannel reception which works in buffer-fill mode.
|
| /Documentation/filesystems/ |
| D | ubifs.rst | 41 UBIFS works on top of UBI. UBI is a separate software layer which may be
53 * JFFS2 works on top of MTD devices, UBIFS depends on UBI and works on
|
| /Documentation/locking/ |
| D | locktypes.rst | 187 lockdep_assert_held(&llock) works as with any other locking primitive.
329 sequence works as expected::
340 preemption. The following code sequence works perfectly correct on both
369 On a non-PREEMPT_RT kernel this works correctly, but on a PREEMPT_RT kernel
401 following code sequence works as expected::
430 preemption. The following substitution works on both kernels::
477 works perfectly::
|
| /Documentation/arch/arm/sti/ |
| D | overview.rst | 25 Flattened Device Tree, which means, It works with any compatible board with
|
| /Documentation/arch/arm/stm32/ |
| D | overview.rst | 27 Flattened Device Tree, which means, it works with any compatible board with
|
| /Documentation/devicetree/bindings/serial/ |
| D | fsl-imx-uart.yaml | 78 Indicate the uart works in DTE mode. The uart works in DCE mode by default.
|
| /Documentation/devicetree/bindings/sound/ |
| D | brcm,bcm63xx-audio.txt | 16 works on Master Mode.
|
| /Documentation/devicetree/bindings/clock/ |
| D | starfive,jh7110-pll.yaml | 11 Each PLL works in integer mode or fraction mode, with configuration
|
12345678910>>...19