Home
last modified time | relevance | path

Searched +full:sda +full:- +full:open +full:- +full:drain (Results 1 – 5 of 5) sorted by relevance

/Documentation/devicetree/bindings/i2c/
Di2c-gpio.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Wolfram Sang <wsa@kernel.org>
13 - $ref: /schemas/i2c/i2c-controller.yaml#
18 - const: i2c-gpio
20 sda-gpios:
22 gpio used for the sda signal, this should be flagged as
23 active high using open drain with (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)
[all …]
/Documentation/driver-api/
Di2c.rst5 the "Inter-IC" bus, a simple bus protocol which is widely used where low
7 some vendors use another name (such as "Two-Wire Interface", TWI) for
8 the same bus. I2C only needs two signals (SCL for clock, SDA for data),
12 I2C is a multi-master bus; open drain signaling is used to arbitrate
38 .. kernel-doc:: include/linux/i2c.h
41 .. kernel-doc:: drivers/i2c/i2c-boardinfo.c
44 .. kernel-doc:: drivers/i2c/i2c-core-base.c
47 .. kernel-doc:: drivers/i2c/i2c-core-smbus.c
Dpin-control.rst9 - Enumerating and naming controllable pins
11 - Multiplexing of pins, pads, fingers (etc) see below for details
13 - Configuration of pins, pads, fingers (etc), such as software-controlled
14 biasing and driving mode specific pins, such as pull-up, pull-down, open drain,
17 Top-level interface
22 - A PIN CONTROLLER is a piece of hardware, usually a set of registers, that
26 - PINS are equal to pads, fingers, balls or whatever packaging input or
30 be sparse - i.e. there may be gaps in the space with numbers where no
60 .. code-block:: c
97 See ``arch/arm/mach-ux500/Kconfig`` for an example.
[all …]
/Documentation/devicetree/bindings/mfd/
Das3722.txt4 -------------------
5 - compatible: Must be "ams,as3722".
6 - reg: I2C device address.
7 - interrupt-controller: AS3722 has internal interrupt controller which takes the
8 interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well
10 - #interrupt-cells: Should be set to 2 for IRQ number and flags.
12 of AS3722 are defined at dt-bindings/mfd/as3722.h
14 interrupts.txt, using dt-bindings/irq.
17 --------------------
18 - ams,enable-internal-int-pullup: Boolean property, to enable internal pullup on
[all …]
/Documentation/driver-api/gpio/
Ddriver.rst26 between 0 and n-1, n being the number of GPIOs managed by the chip.
29 example if a system uses a memory-mapped set of I/O-registers where 32 GPIO
30 lines are handled by one bit per line in a 32-bit register, it makes sense to
44 So for example one platform could use global numbers 32-159 for GPIOs, with a
46 global numbers 0..63 with one set of GPIO controllers, 64-79 with another type
47 of GPIO controller, and on one particular board 80-95 with an FPGA. The legacy
49 2000-2063 to identify GPIO lines in a bank of I2C GPIO expanders.
60 - methods to establish GPIO line direction
61 - methods used to access GPIO line values
62 - method to set electrical configuration for a given GPIO line
[all …]