1 /*
2 * linux/arch/arm/mach-omap1/board-osk.c
3 *
4 * Board specific init for OMAP5912 OSK
5 *
6 * Written by Dirk Behme <dirk.behme@de.bosch.com>
7 *
8 * This program is free software; you can redistribute it and/or modify it
9 * under the terms of the GNU General Public License as published by the
10 * Free Software Foundation; either version 2 of the License, or (at your
11 * option) any later version.
12 *
13 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
14 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
15 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
16 * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
17 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
18 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
19 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
20 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
21 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
22 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
23 *
24 * You should have received a copy of the GNU General Public License along
25 * with this program; if not, write to the Free Software Foundation, Inc.,
26 * 675 Mass Ave, Cambridge, MA 02139, USA.
27 */
28 #include <linux/gpio.h>
29 #include <linux/gpio/machine.h>
30 #include <linux/kernel.h>
31 #include <linux/init.h>
32 #include <linux/platform_device.h>
33 #include <linux/interrupt.h>
34 #include <linux/irq.h>
35 #include <linux/i2c.h>
36 #include <linux/leds.h>
37 #include <linux/smc91x.h>
38 #include <linux/omapfb.h>
39 #include <linux/mtd/mtd.h>
40 #include <linux/mtd/partitions.h>
41 #include <linux/mtd/physmap.h>
42 #include <linux/mfd/tps65010.h>
43 #include <linux/platform_data/gpio-omap.h>
44 #include <linux/platform_data/omap1_bl.h>
45
46 #include <asm/mach-types.h>
47 #include <asm/mach/arch.h>
48 #include <asm/mach/map.h>
49
50 #include "flash.h"
51 #include <mach/mux.h>
52 #include <mach/tc.h>
53
54 #include <mach/hardware.h>
55 #include <mach/usb.h>
56
57 #include "common.h"
58
59 /* Name of the GPIO chip used by the OMAP for GPIOs 0..15 */
60 #define OMAP_GPIO_LABEL "gpio-0-15"
61
62 /* At OMAP5912 OSK the Ethernet is directly connected to CS1 */
63 #define OMAP_OSK_ETHR_START 0x04800300
64
65 /* TPS65010 has four GPIOs. nPG and LED2 can be treated like GPIOs with
66 * alternate pin configurations for hardware-controlled blinking.
67 */
68 #define OSK_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */)
69 # define OSK_TPS_GPIO_USB_PWR_EN (OSK_TPS_GPIO_BASE + 0)
70 # define OSK_TPS_GPIO_LED_D3 (OSK_TPS_GPIO_BASE + 1)
71 # define OSK_TPS_GPIO_LAN_RESET (OSK_TPS_GPIO_BASE + 2)
72 # define OSK_TPS_GPIO_DSP_PWR_EN (OSK_TPS_GPIO_BASE + 3)
73 # define OSK_TPS_GPIO_LED_D9 (OSK_TPS_GPIO_BASE + 4)
74 # define OSK_TPS_GPIO_LED_D2 (OSK_TPS_GPIO_BASE + 5)
75
76 static struct mtd_partition osk_partitions[] = {
77 /* bootloader (U-Boot, etc) in first sector */
78 {
79 .name = "bootloader",
80 .offset = 0,
81 .size = SZ_128K,
82 .mask_flags = MTD_WRITEABLE, /* force read-only */
83 },
84 /* bootloader params in the next sector */
85 {
86 .name = "params",
87 .offset = MTDPART_OFS_APPEND,
88 .size = SZ_128K,
89 .mask_flags = 0,
90 }, {
91 .name = "kernel",
92 .offset = MTDPART_OFS_APPEND,
93 .size = SZ_2M,
94 .mask_flags = 0
95 }, {
96 .name = "filesystem",
97 .offset = MTDPART_OFS_APPEND,
98 .size = MTDPART_SIZ_FULL,
99 .mask_flags = 0
100 }
101 };
102
103 static struct physmap_flash_data osk_flash_data = {
104 .width = 2,
105 .set_vpp = omap1_set_vpp,
106 .parts = osk_partitions,
107 .nr_parts = ARRAY_SIZE(osk_partitions),
108 };
109
110 static struct resource osk_flash_resource = {
111 /* this is on CS3, wherever it's mapped */
112 .flags = IORESOURCE_MEM,
113 };
114
115 static struct platform_device osk5912_flash_device = {
116 .name = "physmap-flash",
117 .id = 0,
118 .dev = {
119 .platform_data = &osk_flash_data,
120 },
121 .num_resources = 1,
122 .resource = &osk_flash_resource,
123 };
124
125 static struct smc91x_platdata osk5912_smc91x_info = {
126 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
127 .leda = RPC_LED_100_10,
128 .ledb = RPC_LED_TX_RX,
129 };
130
131 static struct resource osk5912_smc91x_resources[] = {
132 [0] = {
133 .start = OMAP_OSK_ETHR_START, /* Physical */
134 .end = OMAP_OSK_ETHR_START + 0xf,
135 .flags = IORESOURCE_MEM,
136 },
137 [1] = {
138 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
139 },
140 };
141
142 static struct platform_device osk5912_smc91x_device = {
143 .name = "smc91x",
144 .id = -1,
145 .dev = {
146 .platform_data = &osk5912_smc91x_info,
147 },
148 .num_resources = ARRAY_SIZE(osk5912_smc91x_resources),
149 .resource = osk5912_smc91x_resources,
150 };
151
152 static struct resource osk5912_cf_resources[] = {
153 [0] = {
154 .flags = IORESOURCE_IRQ,
155 },
156 };
157
158 static struct platform_device osk5912_cf_device = {
159 .name = "omap_cf",
160 .id = -1,
161 .dev = {
162 .platform_data = (void *) 2 /* CS2 */,
163 },
164 .num_resources = ARRAY_SIZE(osk5912_cf_resources),
165 .resource = osk5912_cf_resources,
166 };
167
168 static struct platform_device *osk5912_devices[] __initdata = {
169 &osk5912_flash_device,
170 &osk5912_smc91x_device,
171 &osk5912_cf_device,
172 };
173
174 static const struct gpio_led tps_leds[] = {
175 /* NOTE: D9 and D2 have hardware blink support.
176 * Also, D9 requires non-battery power.
177 */
178 { .gpio = OSK_TPS_GPIO_LED_D9, .name = "d9",
179 .default_trigger = "disk-activity", },
180 { .gpio = OSK_TPS_GPIO_LED_D2, .name = "d2", },
181 { .gpio = OSK_TPS_GPIO_LED_D3, .name = "d3", .active_low = 1,
182 .default_trigger = "heartbeat", },
183 };
184
185 static struct gpio_led_platform_data tps_leds_data = {
186 .num_leds = 3,
187 .leds = tps_leds,
188 };
189
190 static struct platform_device osk5912_tps_leds = {
191 .name = "leds-gpio",
192 .id = 0,
193 .dev.platform_data = &tps_leds_data,
194 };
195
osk_tps_setup(struct i2c_client * client,void * context)196 static int osk_tps_setup(struct i2c_client *client, void *context)
197 {
198 if (!IS_BUILTIN(CONFIG_TPS65010))
199 return -ENOSYS;
200
201 /* Set GPIO 1 HIGH to disable VBUS power supply;
202 * OHCI driver powers it up/down as needed.
203 */
204 gpio_request(OSK_TPS_GPIO_USB_PWR_EN, "n_vbus_en");
205 gpio_direction_output(OSK_TPS_GPIO_USB_PWR_EN, 1);
206 /* Free the GPIO again as the driver will request it */
207 gpio_free(OSK_TPS_GPIO_USB_PWR_EN);
208
209 /* Set GPIO 2 high so LED D3 is off by default */
210 tps65010_set_gpio_out_value(GPIO2, HIGH);
211
212 /* Set GPIO 3 low to take ethernet out of reset */
213 gpio_request(OSK_TPS_GPIO_LAN_RESET, "smc_reset");
214 gpio_direction_output(OSK_TPS_GPIO_LAN_RESET, 0);
215
216 /* GPIO4 is VDD_DSP */
217 gpio_request(OSK_TPS_GPIO_DSP_PWR_EN, "dsp_power");
218 gpio_direction_output(OSK_TPS_GPIO_DSP_PWR_EN, 1);
219 /* REVISIT if DSP support isn't configured, power it off ... */
220
221 /* Let LED1 (D9) blink; leds-gpio may override it */
222 tps65010_set_led(LED1, BLINK);
223
224 /* Set LED2 off by default */
225 tps65010_set_led(LED2, OFF);
226
227 /* Enable LOW_PWR handshake */
228 tps65010_set_low_pwr(ON);
229
230 /* Switch VLDO2 to 3.0V for AIC23 */
231 tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V
232 | TPS_LDO1_ENABLE);
233
234 /* register these three LEDs */
235 osk5912_tps_leds.dev.parent = &client->dev;
236 platform_device_register(&osk5912_tps_leds);
237
238 return 0;
239 }
240
241 static struct tps65010_board tps_board = {
242 .base = OSK_TPS_GPIO_BASE,
243 .outmask = 0x0f,
244 .setup = osk_tps_setup,
245 };
246
247 static struct i2c_board_info __initdata osk_i2c_board_info[] = {
248 {
249 /* This device will get the name "i2c-tps65010" */
250 I2C_BOARD_INFO("tps65010", 0x48),
251 .dev_name = "tps65010",
252 .platform_data = &tps_board,
253
254 },
255 {
256 I2C_BOARD_INFO("tlv320aic23", 0x1B),
257 },
258 /* TODO when driver support is ready:
259 * - optionally on Mistral, ov9640 camera sensor at 0x30
260 */
261 };
262
osk_init_smc91x(void)263 static void __init osk_init_smc91x(void)
264 {
265 u32 l;
266
267 if ((gpio_request(0, "smc_irq")) < 0) {
268 printk("Error requesting gpio 0 for smc91x irq\n");
269 return;
270 }
271
272 /* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */
273 l = omap_readl(EMIFS_CCS(1));
274 l |= 0x3;
275 omap_writel(l, EMIFS_CCS(1));
276 }
277
osk_init_cf(void)278 static void __init osk_init_cf(void)
279 {
280 omap_cfg_reg(M7_1610_GPIO62);
281 if ((gpio_request(62, "cf_irq")) < 0) {
282 printk("Error requesting gpio 62 for CF irq\n");
283 return;
284 }
285 /* the CF I/O IRQ is really active-low */
286 irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING);
287 }
288
289 static struct gpiod_lookup_table osk_usb_gpio_table = {
290 .dev_id = "ohci",
291 .table = {
292 /* Power GPIO on the I2C-attached TPS65010 */
293 GPIO_LOOKUP("tps65010", 0, "power", GPIO_ACTIVE_HIGH),
294 GPIO_LOOKUP(OMAP_GPIO_LABEL, 9, "overcurrent",
295 GPIO_ACTIVE_HIGH),
296 },
297 };
298
299 static struct omap_usb_config osk_usb_config __initdata = {
300 /* has usb host connector (A) ... for development it can also
301 * be used, with a NONSTANDARD gender-bending cable/dongle, as
302 * a peripheral.
303 */
304 #if IS_ENABLED(CONFIG_USB_OMAP)
305 .register_dev = 1,
306 .hmc_mode = 0,
307 #else
308 .register_host = 1,
309 .hmc_mode = 16,
310 .rwc = 1,
311 #endif
312 .pins[0] = 2,
313 };
314
315 #ifdef CONFIG_OMAP_OSK_MISTRAL
316 static const struct omap_lcd_config osk_lcd_config __initconst = {
317 .ctrl_name = "internal",
318 };
319 #endif
320
321 #ifdef CONFIG_OMAP_OSK_MISTRAL
322
323 #include <linux/input.h>
324 #include <linux/property.h>
325 #include <linux/spi/spi.h>
326 #include <linux/spi/ads7846.h>
327
328 #include <linux/platform_data/keypad-omap.h>
329
330 static const struct property_entry mistral_at24_properties[] = {
331 PROPERTY_ENTRY_U32("pagesize", 16),
332 { }
333 };
334
335 static struct i2c_board_info __initdata mistral_i2c_board_info[] = {
336 {
337 /* NOTE: powered from LCD supply */
338 I2C_BOARD_INFO("24c04", 0x50),
339 .properties = mistral_at24_properties,
340 },
341 /* TODO when driver support is ready:
342 * - optionally ov9640 camera sensor at 0x30
343 */
344 };
345
346 static const unsigned int osk_keymap[] = {
347 /* KEY(col, row, code) */
348 KEY(0, 0, KEY_F1), /* SW4 */
349 KEY(3, 0, KEY_UP), /* (sw2/up) */
350 KEY(1, 1, KEY_LEFTCTRL), /* SW5 */
351 KEY(2, 1, KEY_LEFT), /* (sw2/left) */
352 KEY(0, 2, KEY_SPACE), /* SW3 */
353 KEY(1, 2, KEY_ESC), /* SW6 */
354 KEY(2, 2, KEY_DOWN), /* (sw2/down) */
355 KEY(2, 3, KEY_ENTER), /* (sw2/select) */
356 KEY(3, 3, KEY_RIGHT), /* (sw2/right) */
357 };
358
359 static const struct matrix_keymap_data osk_keymap_data = {
360 .keymap = osk_keymap,
361 .keymap_size = ARRAY_SIZE(osk_keymap),
362 };
363
364 static struct omap_kp_platform_data osk_kp_data = {
365 .rows = 8,
366 .cols = 8,
367 .keymap_data = &osk_keymap_data,
368 .delay = 9,
369 };
370
371 static struct resource osk5912_kp_resources[] = {
372 [0] = {
373 .start = INT_KEYBOARD,
374 .end = INT_KEYBOARD,
375 .flags = IORESOURCE_IRQ,
376 },
377 };
378
379 static struct platform_device osk5912_kp_device = {
380 .name = "omap-keypad",
381 .id = -1,
382 .dev = {
383 .platform_data = &osk_kp_data,
384 },
385 .num_resources = ARRAY_SIZE(osk5912_kp_resources),
386 .resource = osk5912_kp_resources,
387 };
388
389 static struct omap_backlight_config mistral_bl_data = {
390 .default_intensity = 0xa0,
391 };
392
393 static struct platform_device mistral_bl_device = {
394 .name = "omap-bl",
395 .id = -1,
396 .dev = {
397 .platform_data = &mistral_bl_data,
398 },
399 };
400
401 static struct platform_device osk5912_lcd_device = {
402 .name = "lcd_osk",
403 .id = -1,
404 };
405
406 static const struct gpio_led mistral_gpio_led_pins[] = {
407 {
408 .name = "mistral:red",
409 .default_trigger = "heartbeat",
410 .gpio = 3,
411 },
412 {
413 .name = "mistral:green",
414 .default_trigger = "cpu0",
415 .gpio = OMAP_MPUIO(4),
416 },
417 };
418
419 static struct gpio_led_platform_data mistral_gpio_led_data = {
420 .leds = mistral_gpio_led_pins,
421 .num_leds = ARRAY_SIZE(mistral_gpio_led_pins),
422 };
423
424 static struct platform_device mistral_gpio_leds = {
425 .name = "leds-gpio",
426 .id = -1,
427 .dev = {
428 .platform_data = &mistral_gpio_led_data,
429 },
430 };
431
432 static struct platform_device *mistral_devices[] __initdata = {
433 &osk5912_kp_device,
434 &mistral_bl_device,
435 &osk5912_lcd_device,
436 &mistral_gpio_leds,
437 };
438
mistral_get_pendown_state(void)439 static int mistral_get_pendown_state(void)
440 {
441 return !gpio_get_value(4);
442 }
443
444 static const struct ads7846_platform_data mistral_ts_info = {
445 .model = 7846,
446 .vref_delay_usecs = 100, /* internal, no capacitor */
447 .x_plate_ohms = 419,
448 .y_plate_ohms = 486,
449 .get_pendown_state = mistral_get_pendown_state,
450 };
451
452 static struct spi_board_info __initdata mistral_boardinfo[] = { {
453 /* MicroWire (bus 2) CS0 has an ads7846e */
454 .modalias = "ads7846",
455 .platform_data = &mistral_ts_info,
456 .max_speed_hz = 120000 /* max sample rate at 3V */
457 * 26 /* command + data + overhead */,
458 .bus_num = 2,
459 .chip_select = 0,
460 } };
461
462 static irqreturn_t
osk_mistral_wake_interrupt(int irq,void * ignored)463 osk_mistral_wake_interrupt(int irq, void *ignored)
464 {
465 return IRQ_HANDLED;
466 }
467
osk_mistral_init(void)468 static void __init osk_mistral_init(void)
469 {
470 /* NOTE: we could actually tell if there's a Mistral board
471 * attached, e.g. by trying to read something from the ads7846.
472 * But this arch_init() code is too early for that, since we
473 * can't talk to the ads or even the i2c eeprom.
474 */
475
476 /* parallel camera interface */
477 omap_cfg_reg(J15_1610_CAM_LCLK);
478 omap_cfg_reg(J18_1610_CAM_D7);
479 omap_cfg_reg(J19_1610_CAM_D6);
480 omap_cfg_reg(J14_1610_CAM_D5);
481 omap_cfg_reg(K18_1610_CAM_D4);
482 omap_cfg_reg(K19_1610_CAM_D3);
483 omap_cfg_reg(K15_1610_CAM_D2);
484 omap_cfg_reg(K14_1610_CAM_D1);
485 omap_cfg_reg(L19_1610_CAM_D0);
486 omap_cfg_reg(L18_1610_CAM_VS);
487 omap_cfg_reg(L15_1610_CAM_HS);
488 omap_cfg_reg(M19_1610_CAM_RSTZ);
489 omap_cfg_reg(Y15_1610_CAM_OUTCLK);
490
491 /* serial camera interface */
492 omap_cfg_reg(H19_1610_CAM_EXCLK);
493 omap_cfg_reg(W13_1610_CCP_CLKM);
494 omap_cfg_reg(Y12_1610_CCP_CLKP);
495 /* CCP_DATAM CONFLICTS WITH UART1.TX (and serial console) */
496 /* omap_cfg_reg(Y14_1610_CCP_DATAM); */
497 omap_cfg_reg(W14_1610_CCP_DATAP);
498
499 /* CAM_PWDN */
500 if (gpio_request(11, "cam_pwdn") == 0) {
501 omap_cfg_reg(N20_1610_GPIO11);
502 gpio_direction_output(11, 0);
503 } else
504 pr_debug("OSK+Mistral: CAM_PWDN is awol\n");
505
506
507 /* omap_cfg_reg(P19_1610_GPIO6); */ /* BUSY */
508 gpio_request(6, "ts_busy");
509 gpio_direction_input(6);
510
511 omap_cfg_reg(P20_1610_GPIO4); /* PENIRQ */
512 gpio_request(4, "ts_int");
513 gpio_direction_input(4);
514 irq_set_irq_type(gpio_to_irq(4), IRQ_TYPE_EDGE_FALLING);
515
516 mistral_boardinfo[0].irq = gpio_to_irq(4);
517 spi_register_board_info(mistral_boardinfo,
518 ARRAY_SIZE(mistral_boardinfo));
519
520 /* the sideways button (SW1) is for use as a "wakeup" button
521 *
522 * NOTE: The Mistral board has the wakeup button (SW1) wired
523 * to the LCD 3.3V rail, which is powered down during suspend.
524 * To allow this button to wake up the omap, work around this
525 * HW bug by rewiring SW1 to use the main 3.3V rail.
526 */
527 omap_cfg_reg(N15_1610_MPUIO2);
528 if (gpio_request(OMAP_MPUIO(2), "wakeup") == 0) {
529 int ret = 0;
530 int irq = gpio_to_irq(OMAP_MPUIO(2));
531
532 gpio_direction_input(OMAP_MPUIO(2));
533 irq_set_irq_type(irq, IRQ_TYPE_EDGE_RISING);
534 /* share the IRQ in case someone wants to use the
535 * button for more than wakeup from system sleep.
536 */
537 ret = request_irq(irq,
538 &osk_mistral_wake_interrupt,
539 IRQF_SHARED, "mistral_wakeup",
540 &osk_mistral_wake_interrupt);
541 if (ret != 0) {
542 gpio_free(OMAP_MPUIO(2));
543 printk(KERN_ERR "OSK+Mistral: no wakeup irq, %d?\n",
544 ret);
545 } else
546 enable_irq_wake(irq);
547 } else
548 printk(KERN_ERR "OSK+Mistral: wakeup button is awol\n");
549
550 /* LCD: backlight, and power; power controls other devices on the
551 * board, like the touchscreen, EEPROM, and wakeup (!) switch.
552 */
553 omap_cfg_reg(PWL);
554 if (gpio_request(2, "lcd_pwr") == 0)
555 gpio_direction_output(2, 1);
556
557 /*
558 * GPIO based LEDs
559 */
560 omap_cfg_reg(P18_1610_GPIO3);
561 omap_cfg_reg(MPUIO4);
562
563 i2c_register_board_info(1, mistral_i2c_board_info,
564 ARRAY_SIZE(mistral_i2c_board_info));
565
566 platform_add_devices(mistral_devices, ARRAY_SIZE(mistral_devices));
567 }
568 #else
osk_mistral_init(void)569 static void __init osk_mistral_init(void) { }
570 #endif
571
572 #define EMIFS_CS3_VAL (0x88013141)
573
osk_init(void)574 static void __init osk_init(void)
575 {
576 u32 l;
577
578 osk_init_smc91x();
579 osk_init_cf();
580
581 /* Workaround for wrong CS3 (NOR flash) timing
582 * There are some U-Boot versions out there which configure
583 * wrong CS3 memory timings. This mainly leads to CRC
584 * or similar errors if you use NOR flash (e.g. with JFFS2)
585 */
586 l = omap_readl(EMIFS_CCS(3));
587 if (l != EMIFS_CS3_VAL)
588 omap_writel(EMIFS_CS3_VAL, EMIFS_CCS(3));
589
590 osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
591 osk_flash_resource.end += SZ_32M - 1;
592 osk5912_smc91x_resources[1].start = gpio_to_irq(0);
593 osk5912_smc91x_resources[1].end = gpio_to_irq(0);
594 osk5912_cf_resources[0].start = gpio_to_irq(62);
595 osk5912_cf_resources[0].end = gpio_to_irq(62);
596 platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
597
598 l = omap_readl(USB_TRANSCEIVER_CTRL);
599 l |= (3 << 1);
600 omap_writel(l, USB_TRANSCEIVER_CTRL);
601
602 gpiod_add_lookup_table(&osk_usb_gpio_table);
603 omap1_usb_init(&osk_usb_config);
604
605 /* irq for tps65010 chip */
606 /* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */
607 if (gpio_request(OMAP_MPUIO(1), "tps65010") == 0)
608 gpio_direction_input(OMAP_MPUIO(1));
609
610 omap_serial_init();
611 osk_i2c_board_info[0].irq = gpio_to_irq(OMAP_MPUIO(1));
612 omap_register_i2c_bus(1, 400, osk_i2c_board_info,
613 ARRAY_SIZE(osk_i2c_board_info));
614 osk_mistral_init();
615
616 #ifdef CONFIG_OMAP_OSK_MISTRAL
617 omapfb_set_lcd_config(&osk_lcd_config);
618 #endif
619
620 }
621
622 MACHINE_START(OMAP_OSK, "TI-OSK")
623 /* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
624 .atag_offset = 0x100,
625 .map_io = omap16xx_map_io,
626 .init_early = omap1_init_early,
627 .init_irq = omap1_init_irq,
628 .handle_irq = omap1_handle_irq,
629 .init_machine = osk_init,
630 .init_late = omap1_init_late,
631 .init_time = omap1_timer_init,
632 .restart = omap1_restart,
633 MACHINE_END
634