• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1STMicroelectronics STi MIPHY28LP PHY binding
2============================================
3
4This binding describes a miphy device that is used to control PHY hardware
5for SATA, PCIe or USB3.
6
7Required properties (controller (parent) node):
8- compatible	: Should be "st,miphy28lp-phy".
9- st,syscfg	: Should be a phandle of the system configuration register group
10		  which contain the SATA, PCIe or USB3 mode setting bits.
11
12Required nodes	:  A sub-node is required for each channel the controller
13		   provides. Address range information including the usual
14		   'reg' and 'reg-names' properties are used inside these
15		   nodes to describe the controller's topology. These nodes
16		   are translated by the driver's .xlate() function.
17
18Required properties (port (child) node):
19- #phy-cells	: Should be 1 (See second example)
20		  Cell after port phandle is device type from:
21			- PHY_TYPE_SATA
22			- PHY_TYPE_PCI
23			- PHY_TYPE_USB3
24- reg		: Address and length of the register set for the device.
25- reg-names	: The names of the register addresses corresponding to the registers
26		  filled in "reg". It can also contain the offset of the system configuration
27		  registers used as glue-logic to setup the device for SATA/PCIe or USB3
28		  devices.
29- st,syscfg	: Offset of the parent configuration register.
30- resets	: phandle to the parent reset controller.
31- reset-names	: Associated name must be "miphy-sw-rst".
32
33Optional properties (port (child) node):
34- st,osc-rdy		: to check the MIPHY0_OSC_RDY status in the glue-logic. This
35			  is not available in all the MiPHY. For example, for STiH407, only the
36			  MiPHY0 has this bit.
37- st,osc-force-ext	: to select the external oscillator. This can change from
38			  different MiPHY inside the same SoC.
39- st,sata_gen		: to select which SATA_SPDMODE has to be set in the SATA system config
40			  register.
41- st,px_rx_pol_inv	: to invert polarity of RXn/RXp (respectively negative line and positive
42			  line).
43- st,scc-on		: enable ssc to reduce effects of EMI (only for sata or PCIe).
44- st,tx-impedance-comp	: to compensate tx impedance avoiding out of range values.
45
46example:
47
48		miphy28lp_phy: miphy28lp@9b22000 {
49			compatible = "st,miphy28lp-phy";
50			st,syscfg = <&syscfg_core>;
51			#address-cells	= <1>;
52			#size-cells	= <1>;
53			ranges;
54
55			phy_port0: port@9b22000 {
56				reg = <0x9b22000 0xff>,
57				      <0x9b09000 0xff>,
58				      <0x9b04000 0xff>;
59				reg-names = "sata-up",
60					    "pcie-up",
61					    "pipew";
62
63				st,syscfg = <0x114 0x818 0xe0 0xec>;
64				#phy-cells = <1>;
65				st,osc-rdy;
66				reset-names = "miphy-sw-rst";
67				resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
68			};
69
70			phy_port1: port@9b2a000 {
71				reg = <0x9b2a000 0xff>,
72				      <0x9b19000 0xff>,
73				      <0x9b14000 0xff>;
74				reg-names = "sata-up",
75					    "pcie-up",
76					    "pipew";
77
78				st,syscfg = <0x118 0x81c 0xe4 0xf0>;
79
80				#phy-cells = <1>;
81				st,osc-force-ext;
82				reset-names = "miphy-sw-rst";
83				resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
84			};
85
86			phy_port2: port@8f95000 {
87				reg = <0x8f95000 0xff>,
88				      <0x8f90000 0xff>;
89				reg-names = "pipew",
90					    "usb3-up";
91
92				st,syscfg = <0x11c 0x820>;
93
94				#phy-cells = <1>;
95				reset-names = "miphy-sw-rst";
96				resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
97			};
98		};
99
100
101Specifying phy control of devices
102=================================
103
104Device nodes should specify the configuration required in their "phys"
105property, containing a phandle to the miphy device node and an index
106specifying which configuration to use, as described in phy-bindings.txt.
107
108example:
109		sata0: sata@9b20000  {
110			...
111			phys		= <&phy_port0 PHY_TYPE_SATA>;
112			...
113		};
114
115Macro definitions for the supported miphy configuration can be found in:
116
117include/dt-bindings/phy/phy.h
118