1/* 2 * BSD LICENSE 3 * 4 * Copyright(c) 2016 Broadcom. All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 10 * * Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * * Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in 14 * the documentation and/or other materials provided with the 15 * distribution. 16 * * Neither the name of Broadcom Corporation nor the names of its 17 * contributors may be used to endorse or promote products derived 18 * from this software without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT 26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33/dts-v1/; 34 35#include "bcm-nsp.dtsi" 36#include <dt-bindings/gpio/gpio.h> 37 38/ { 39 model = "NorthStar Plus SVK (BCM958623HR)"; 40 compatible = "brcm,bcm58623", "brcm,nsp"; 41 42 chosen { 43 stdout-path = "serial0:115200n8"; 44 }; 45 46 memory@60000000 { 47 device_type = "memory"; 48 reg = <0x60000000 0x80000000>; 49 }; 50 51 gpio-restart { 52 compatible = "gpio-restart"; 53 gpios = <&gpioa 15 GPIO_ACTIVE_LOW>; 54 open-source; 55 priority = <200>; 56 }; 57}; 58 59/* USB 3 and SLIC support needed to be complete */ 60 61&dma { 62 status = "okay"; 63}; 64 65&amac0 { 66 status = "okay"; 67}; 68 69&amac1 { 70 status = "okay"; 71}; 72 73&amac2 { 74 status = "okay"; 75}; 76 77&ehci0 { 78 status = "okay"; 79}; 80 81&nand_controller { 82 nand@0 { 83 compatible = "brcm,nandcs"; 84 reg = <0>; 85 nand-on-flash-bbt; 86 87 #address-cells = <1>; 88 #size-cells = <1>; 89 90 nand-ecc-strength = <24>; 91 nand-ecc-step-size = <1024>; 92 93 brcm,nand-oob-sector-size = <27>; 94 95 partition@0 { 96 label = "nboot"; 97 reg = <0x00000000 0x00200000>; 98 read-only; 99 }; 100 partition@200000 { 101 label = "nenv"; 102 reg = <0x00200000 0x00400000>; 103 }; 104 partition@600000 { 105 label = "nsystem"; 106 reg = <0x00600000 0x00a00000>; 107 }; 108 partition@1000000 { 109 label = "nrootfs"; 110 reg = <0x01000000 0x03000000>; 111 }; 112 partition@4000000 { 113 label = "ncustfs"; 114 reg = <0x04000000 0x3c000000>; 115 }; 116 }; 117}; 118 119&ohci0 { 120 status = "okay"; 121}; 122 123&pcie0 { 124 status = "okay"; 125}; 126 127&pcie1 { 128 status = "okay"; 129}; 130 131&pinctrl { 132 pinctrl-names = "default"; 133 pinctrl-0 = <&nand_sel>; 134 nand_sel: nand_sel { 135 function = "nand"; 136 groups = "nand_grp"; 137 }; 138}; 139 140&sata_phy0 { 141 status = "okay"; 142}; 143 144&qspi { 145 bspi-sel = <0>; 146 flash: m25p80@0 { 147 #address-cells = <1>; 148 #size-cells = <1>; 149 compatible = "m25p80"; 150 reg = <0x0>; 151 spi-max-frequency = <12500000>; 152 m25p,fast-read; 153 spi-cpol; 154 spi-cpha; 155 156 partition@0 { 157 label = "boot"; 158 reg = <0x00000000 0x000a0000>; 159 }; 160 161 partition@a0000 { 162 label = "env"; 163 reg = <0x000a0000 0x00060000>; 164 }; 165 166 partition@100000 { 167 label = "system"; 168 reg = <0x00100000 0x00600000>; 169 }; 170 171 partition@700000 { 172 label = "rootfs"; 173 reg = <0x00700000 0x01900000>; 174 }; 175 }; 176}; 177 178&srab { 179 compatible = "brcm,bcm58623-srab", "brcm,nsp-srab"; 180 status = "okay"; 181 182 ports { 183 #address-cells = <1>; 184 #size-cells = <0>; 185 186 port@0 { 187 label = "port0"; 188 reg = <0>; 189 }; 190 191 port@1 { 192 label = "port1"; 193 reg = <1>; 194 }; 195 196 port@2 { 197 label = "port2"; 198 reg = <2>; 199 }; 200 201 port@3 { 202 label = "port3"; 203 reg = <3>; 204 }; 205 206 port@4 { 207 label = "port4"; 208 reg = <4>; 209 }; 210 211 port@8 { 212 ethernet = <&amac2>; 213 label = "cpu"; 214 reg = <8>; 215 fixed-link { 216 speed = <1000>; 217 full-duplex; 218 }; 219 }; 220 }; 221}; 222 223&uart0 { 224 status = "okay"; 225}; 226 227&usb3_phy { 228 status = "okay"; 229}; 230 231&xhci { 232 status = "okay"; 233}; 234