1// SPDX-License-Identifier: GPL-2.0+ 2/* 3 * Copyright (C) 2015 Altera Corporation <www.altera.com> 4 */ 5#include "socfpga_arria10.dtsi" 6 7/ { 8 model = "Altera SOCFPGA Arria 10"; 9 compatible = "altr,socfpga-arria10", "altr,socfpga"; 10 11 aliases { 12 ethernet0 = &gmac0; 13 serial0 = &uart1; 14 }; 15 16 chosen { 17 bootargs = "earlyprintk"; 18 stdout-path = "serial0:115200n8"; 19 }; 20 21 memory@0 { 22 name = "memory"; 23 device_type = "memory"; 24 reg = <0x0 0x40000000>; /* 1GB */ 25 }; 26 27 a10leds { 28 compatible = "gpio-leds"; 29 30 a10sr_led0 { 31 label = "a10sr-led0"; 32 gpios = <&a10sr_gpio 0 1>; 33 }; 34 35 a10sr_led1 { 36 label = "a10sr-led1"; 37 gpios = <&a10sr_gpio 1 1>; 38 }; 39 40 a10sr_led2 { 41 label = "a10sr-led2"; 42 gpios = <&a10sr_gpio 2 1>; 43 }; 44 45 a10sr_led3 { 46 label = "a10sr-led3"; 47 gpios = <&a10sr_gpio 3 1>; 48 }; 49 }; 50 51 ref_033v: 033-v-ref { 52 compatible = "regulator-fixed"; 53 regulator-name = "0.33V"; 54 regulator-min-microvolt = <330000>; 55 regulator-max-microvolt = <330000>; 56 }; 57 58 soc { 59 clkmgr@ffd04000 { 60 clocks { 61 osc1 { 62 clock-frequency = <25000000>; 63 }; 64 }; 65 }; 66 }; 67}; 68 69&gmac0 { 70 phy-mode = "rgmii"; 71 phy-addr = <0xffffffff>; /* probe for phy addr */ 72 73 /* 74 * These skews assume the user's FPGA design is adding 600ps of delay 75 * for TX_CLK on Arria 10. 76 * 77 * All skews are offset since hardware skew values for the ksz9031 78 * range from a negative skew to a positive skew. 79 * See the micrel-ksz90x1.txt Documentation file for details. 80 */ 81 txd0-skew-ps = <0>; /* -420ps */ 82 txd1-skew-ps = <0>; /* -420ps */ 83 txd2-skew-ps = <0>; /* -420ps */ 84 txd3-skew-ps = <0>; /* -420ps */ 85 rxd0-skew-ps = <420>; /* 0ps */ 86 rxd1-skew-ps = <420>; /* 0ps */ 87 rxd2-skew-ps = <420>; /* 0ps */ 88 rxd3-skew-ps = <420>; /* 0ps */ 89 txen-skew-ps = <0>; /* -420ps */ 90 txc-skew-ps = <1860>; /* 960ps */ 91 rxdv-skew-ps = <420>; /* 0ps */ 92 rxc-skew-ps = <1680>; /* 780ps */ 93 max-frame-size = <3800>; 94 status = "okay"; 95}; 96 97&gpio1 { 98 status = "okay"; 99}; 100 101&spi1 { 102 status = "okay"; 103 104 resource-manager@0 { 105 compatible = "altr,a10sr"; 106 reg = <0>; 107 spi-max-frequency = <100000>; 108 /* low-level active IRQ at GPIO1_5 */ 109 interrupt-parent = <&portb>; 110 interrupts = <5 IRQ_TYPE_LEVEL_LOW>; 111 interrupt-controller; 112 #interrupt-cells = <2>; 113 114 a10sr_gpio: gpio-controller { 115 compatible = "altr,a10sr-gpio"; 116 gpio-controller; 117 #gpio-cells = <2>; 118 }; 119 120 a10sr_rst: reset-controller { 121 compatible = "altr,a10sr-reset"; 122 #reset-cells = <1>; 123 }; 124 }; 125}; 126 127&i2c1 { 128 status = "okay"; 129 130 /* 131 * adjust the falling times to decrease the i2c frequency to 50Khz 132 * because the LCD module does not work at the standard 100Khz 133 */ 134 clock-frequency = <100000>; 135 i2c-sda-falling-time-ns = <6000>; 136 i2c-scl-falling-time-ns = <6000>; 137 138 adc@14 { 139 compatible = "lltc,ltc2497"; 140 reg = <0x14>; 141 vref-supply = <&ref_033v>; 142 }; 143 144 adc@16 { 145 compatible = "lltc,ltc2497"; 146 reg = <0x16>; 147 vref-supply = <&ref_033v>; 148 }; 149 150 eeprom@51 { 151 compatible = "atmel,24c32"; 152 reg = <0x51>; 153 pagesize = <32>; 154 }; 155 156 rtc@68 { 157 compatible = "dallas,ds1339"; 158 reg = <0x68>; 159 }; 160 161 ltc@5c { 162 compatible = "ltc2977"; 163 reg = <0x5c>; 164 }; 165 166 temp@4c { 167 compatible = "maxim,max1619"; 168 reg = <0x4c>; 169 }; 170}; 171 172&uart1 { 173 status = "okay"; 174}; 175 176&usb0 { 177 status = "okay"; 178 disable-over-current; 179}; 180 181&watchdog1 { 182 status = "okay"; 183}; 184