1Allows you to dynamically create a list of IP addresses and then match against 2that list in a few different ways. 3.PP 4For example, you can create a "badguy" list out of people attempting to connect 5to port 139 on your firewall and then DROP all future packets from them without 6considering them. 7.PP 8\fB\-\-set\fP, \fB\-\-rcheck\fP, \fB\-\-update\fP and \fB\-\-remove\fP are 9mutually exclusive. 10.TP 11\fB\-\-name\fP \fIname\fP 12Specify the list to use for the commands. If no name is given then 13\fBDEFAULT\fP will be used. 14.TP 15[\fB!\fP] \fB\-\-set\fP 16This will add the source address of the packet to the list. If the source 17address is already in the list, this will update the existing entry. This will 18always return success (or failure if \fB!\fP is passed in). 19.TP 20\fB\-\-rsource\fP 21Match/save the source address of each packet in the recent list table. This 22is the default. 23.TP 24\fB\-\-rdest\fP 25Match/save the destination address of each packet in the recent list table. 26.TP 27\fB\-\-mask\fP \fInetmask\fP 28Netmask that will be applied to this recent list. 29.TP 30[\fB!\fP] \fB\-\-rcheck\fP 31Check if the source address of the packet is currently in the list. 32.TP 33[\fB!\fP] \fB\-\-update\fP 34Like \fB\-\-rcheck\fP, except it will update the "last seen" timestamp if it 35matches. 36.TP 37[\fB!\fP] \fB\-\-remove\fP 38Check if the source address of the packet is currently in the list and if so 39that address will be removed from the list and the rule will return true. If 40the address is not found, false is returned. 41.TP 42\fB\-\-seconds\fP \fIseconds\fP 43This option must be used in conjunction with one of \fB\-\-rcheck\fP or 44\fB\-\-update\fP. When used, this will narrow the match to only happen when the 45address is in the list and was seen within the last given number of seconds. 46.TP 47\fB\-\-reap\fP 48This option can only be used in conjunction with \fB\-\-seconds\fP. 49When used, this will cause entries older than the last given number of seconds 50to be purged. 51.TP 52\fB\-\-hitcount\fP \fIhits\fP 53This option must be used in conjunction with one of \fB\-\-rcheck\fP or 54\fB\-\-update\fP. When used, this will narrow the match to only happen when the 55address is in the list and packets had been received greater than or equal to 56the given value. This option may be used along with \fB\-\-seconds\fP to create 57an even narrower match requiring a certain number of hits within a specific 58time frame. The maximum value for the hitcount parameter is given by the 59"ip_pkt_list_tot" parameter of the xt_recent kernel module. Exceeding this 60value on the command line will cause the rule to be rejected. 61.TP 62\fB\-\-rttl\fP 63This option may only be used in conjunction with one of \fB\-\-rcheck\fP or 64\fB\-\-update\fP. When used, this will narrow the match to only happen when the 65address is in the list and the TTL of the current packet matches that of the 66packet which hit the \fB\-\-set\fP rule. This may be useful if you have problems 67with people faking their source address in order to DoS you via this module by 68disallowing others access to your site by sending bogus packets to you. 69.PP 70Examples: 71.IP 72iptables \-A FORWARD \-m recent \-\-name badguy \-\-rcheck \-\-seconds 60 \-j DROP 73.IP 74iptables \-A FORWARD \-p tcp \-i eth0 \-\-dport 139 \-m recent \-\-name badguy \-\-set \-j DROP 75.PP 76\fB/proc/net/xt_recent/*\fP are the current lists of addresses and information 77about each entry of each list. 78.PP 79Each file in \fB/proc/net/xt_recent/\fP can be read from to see the current 80list or written two using the following commands to modify the list: 81.TP 82\fBecho +\fP\fIaddr\fP\fB >/proc/net/xt_recent/DEFAULT\fP 83to add \fIaddr\fP to the DEFAULT list 84.TP 85\fBecho \-\fP\fIaddr\fP\fB >/proc/net/xt_recent/DEFAULT\fP 86to remove \fIaddr\fP from the DEFAULT list 87.TP 88\fBecho / >/proc/net/xt_recent/DEFAULT\fP 89to flush the DEFAULT list (remove all entries). 90.PP 91The module itself accepts parameters, defaults shown: 92.TP 93\fBip_list_tot\fP=\fI100\fP 94Number of addresses remembered per table. 95.TP 96\fBip_pkt_list_tot\fP=\fI20\fP 97Number of packets per address remembered. 98.TP 99\fBip_list_hash_size\fP=\fI0\fP 100Hash table size. 0 means to calculate it based on ip_list_tot, default: 512. 101.TP 102\fBip_list_perms\fP=\fI0644\fP 103Permissions for /proc/net/xt_recent/* files. 104.TP 105\fBip_list_uid\fP=\fI0\fP 106Numerical UID for ownership of /proc/net/xt_recent/* files. 107.TP 108\fBip_list_gid\fP=\fI0\fP 109Numerical GID for ownership of /proc/net/xt_recent/* files. 110