1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Copyright (C) 2014-2016 Stefan Roese <sr@denx.de>
4 */
5
6 #include <common.h>
7 #include <ahci.h>
8 #include <linux/mbus.h>
9 #include <asm/io.h>
10 #include <asm/pl310.h>
11 #include <asm/arch/cpu.h>
12 #include <asm/arch/soc.h>
13 #include <sdhci.h>
14
15 #define DDR_BASE_CS_OFF(n) (0x0000 + ((n) << 3))
16 #define DDR_SIZE_CS_OFF(n) (0x0004 + ((n) << 3))
17
18 static struct mbus_win windows[] = {
19 /* SPI */
20 { MBUS_SPI_BASE, MBUS_SPI_SIZE,
21 CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_SPIFLASH },
22
23 /* NOR */
24 { MBUS_BOOTROM_BASE, MBUS_BOOTROM_SIZE,
25 CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_BOOTROM },
26 };
27
lowlevel_init(void)28 void lowlevel_init(void)
29 {
30 /*
31 * Dummy implementation, we only need LOWLEVEL_INIT
32 * on Armada to configure CP15 in start.S / cpu_init_cp15()
33 */
34 }
35
reset_cpu(unsigned long ignored)36 void reset_cpu(unsigned long ignored)
37 {
38 struct mvebu_system_registers *reg =
39 (struct mvebu_system_registers *)MVEBU_SYSTEM_REG_BASE;
40
41 writel(readl(®->rstoutn_mask) | 1, ®->rstoutn_mask);
42 writel(readl(®->sys_soft_rst) | 1, ®->sys_soft_rst);
43 while (1)
44 ;
45 }
46
mvebu_soc_family(void)47 int mvebu_soc_family(void)
48 {
49 u16 devid = (readl(MVEBU_REG_PCIE_DEVID) >> 16) & 0xffff;
50
51 switch (devid) {
52 case SOC_MV78230_ID:
53 case SOC_MV78260_ID:
54 case SOC_MV78460_ID:
55 return MVEBU_SOC_AXP;
56
57 case SOC_88F6720_ID:
58 return MVEBU_SOC_A375;
59
60 case SOC_88F6810_ID:
61 case SOC_88F6820_ID:
62 case SOC_88F6828_ID:
63 return MVEBU_SOC_A38X;
64
65 case SOC_98DX3236_ID:
66 case SOC_98DX3336_ID:
67 case SOC_98DX4251_ID:
68 return MVEBU_SOC_MSYS;
69 }
70
71 return MVEBU_SOC_UNKNOWN;
72 }
73
74 #if defined(CONFIG_DISPLAY_CPUINFO)
75
76 #if defined(CONFIG_ARMADA_375)
77 /* SAR frequency values for Armada 375 */
78 static const struct sar_freq_modes sar_freq_tab[] = {
79 { 0, 0x0, 266, 133, 266 },
80 { 1, 0x0, 333, 167, 167 },
81 { 2, 0x0, 333, 167, 222 },
82 { 3, 0x0, 333, 167, 333 },
83 { 4, 0x0, 400, 200, 200 },
84 { 5, 0x0, 400, 200, 267 },
85 { 6, 0x0, 400, 200, 400 },
86 { 7, 0x0, 500, 250, 250 },
87 { 8, 0x0, 500, 250, 334 },
88 { 9, 0x0, 500, 250, 500 },
89 { 10, 0x0, 533, 267, 267 },
90 { 11, 0x0, 533, 267, 356 },
91 { 12, 0x0, 533, 267, 533 },
92 { 13, 0x0, 600, 300, 300 },
93 { 14, 0x0, 600, 300, 400 },
94 { 15, 0x0, 600, 300, 600 },
95 { 16, 0x0, 666, 333, 333 },
96 { 17, 0x0, 666, 333, 444 },
97 { 18, 0x0, 666, 333, 666 },
98 { 19, 0x0, 800, 400, 267 },
99 { 20, 0x0, 800, 400, 400 },
100 { 21, 0x0, 800, 400, 534 },
101 { 22, 0x0, 900, 450, 300 },
102 { 23, 0x0, 900, 450, 450 },
103 { 24, 0x0, 900, 450, 600 },
104 { 25, 0x0, 1000, 500, 500 },
105 { 26, 0x0, 1000, 500, 667 },
106 { 27, 0x0, 1000, 333, 500 },
107 { 28, 0x0, 400, 400, 400 },
108 { 29, 0x0, 1100, 550, 550 },
109 { 0xff, 0xff, 0, 0, 0 } /* 0xff marks end of array */
110 };
111 #elif defined(CONFIG_ARMADA_38X)
112 /* SAR frequency values for Armada 38x */
113 static const struct sar_freq_modes sar_freq_tab[] = {
114 { 0x0, 0x0, 666, 333, 333 },
115 { 0x2, 0x0, 800, 400, 400 },
116 { 0x4, 0x0, 1066, 533, 533 },
117 { 0x6, 0x0, 1200, 600, 600 },
118 { 0x8, 0x0, 1332, 666, 666 },
119 { 0xc, 0x0, 1600, 800, 800 },
120 { 0x10, 0x0, 1866, 933, 933 },
121 { 0x13, 0x0, 2000, 1000, 933 },
122 { 0xff, 0xff, 0, 0, 0 } /* 0xff marks end of array */
123 };
124 #else
125 /* SAR frequency values for Armada XP */
126 static const struct sar_freq_modes sar_freq_tab[] = {
127 { 0xa, 0x5, 800, 400, 400 },
128 { 0x1, 0x5, 1066, 533, 533 },
129 { 0x2, 0x5, 1200, 600, 600 },
130 { 0x2, 0x9, 1200, 600, 400 },
131 { 0x3, 0x5, 1333, 667, 667 },
132 { 0x4, 0x5, 1500, 750, 750 },
133 { 0x4, 0x9, 1500, 750, 500 },
134 { 0xb, 0x9, 1600, 800, 533 },
135 { 0xb, 0xa, 1600, 800, 640 },
136 { 0xb, 0x5, 1600, 800, 800 },
137 { 0xff, 0xff, 0, 0, 0 } /* 0xff marks end of array */
138 };
139 #endif
140
get_sar_freq(struct sar_freq_modes * sar_freq)141 void get_sar_freq(struct sar_freq_modes *sar_freq)
142 {
143 u32 val;
144 u32 freq;
145 int i;
146
147 #if defined(CONFIG_ARMADA_375)
148 val = readl(CONFIG_SAR2_REG); /* SAR - Sample At Reset */
149 #else
150 val = readl(CONFIG_SAR_REG); /* SAR - Sample At Reset */
151 #endif
152 freq = (val & SAR_CPU_FREQ_MASK) >> SAR_CPU_FREQ_OFFS;
153 #if defined(SAR2_CPU_FREQ_MASK)
154 /*
155 * Shift CPU0 clock frequency select bit from SAR2 register
156 * into correct position
157 */
158 freq |= ((readl(CONFIG_SAR2_REG) & SAR2_CPU_FREQ_MASK)
159 >> SAR2_CPU_FREQ_OFFS) << 3;
160 #endif
161 for (i = 0; sar_freq_tab[i].val != 0xff; i++) {
162 if (sar_freq_tab[i].val == freq) {
163 #if defined(CONFIG_ARMADA_375) || defined(CONFIG_ARMADA_38X)
164 *sar_freq = sar_freq_tab[i];
165 return;
166 #else
167 int k;
168 u8 ffc;
169
170 ffc = (val & SAR_FFC_FREQ_MASK) >>
171 SAR_FFC_FREQ_OFFS;
172 for (k = i; sar_freq_tab[k].ffc != 0xff; k++) {
173 if (sar_freq_tab[k].ffc == ffc) {
174 *sar_freq = sar_freq_tab[k];
175 return;
176 }
177 }
178 i = k;
179 #endif
180 }
181 }
182
183 /* SAR value not found, return 0 for frequencies */
184 *sar_freq = sar_freq_tab[i - 1];
185 }
186
print_cpuinfo(void)187 int print_cpuinfo(void)
188 {
189 u16 devid = (readl(MVEBU_REG_PCIE_DEVID) >> 16) & 0xffff;
190 u8 revid = readl(MVEBU_REG_PCIE_REVID) & 0xff;
191 struct sar_freq_modes sar_freq;
192
193 puts("SoC: ");
194
195 switch (devid) {
196 case SOC_MV78230_ID:
197 puts("MV78230-");
198 break;
199 case SOC_MV78260_ID:
200 puts("MV78260-");
201 break;
202 case SOC_MV78460_ID:
203 puts("MV78460-");
204 break;
205 case SOC_88F6720_ID:
206 puts("MV88F6720-");
207 break;
208 case SOC_88F6810_ID:
209 puts("MV88F6810-");
210 break;
211 case SOC_88F6820_ID:
212 puts("MV88F6820-");
213 break;
214 case SOC_88F6828_ID:
215 puts("MV88F6828-");
216 break;
217 case SOC_98DX3236_ID:
218 puts("98DX3236-");
219 break;
220 case SOC_98DX3336_ID:
221 puts("98DX3336-");
222 break;
223 case SOC_98DX4251_ID:
224 puts("98DX4251-");
225 break;
226 default:
227 puts("Unknown-");
228 break;
229 }
230
231 if (mvebu_soc_family() == MVEBU_SOC_AXP) {
232 switch (revid) {
233 case 1:
234 puts("A0");
235 break;
236 case 2:
237 puts("B0");
238 break;
239 default:
240 printf("?? (%x)", revid);
241 break;
242 }
243 }
244
245 if (mvebu_soc_family() == MVEBU_SOC_A375) {
246 switch (revid) {
247 case MV_88F67XX_A0_ID:
248 puts("A0");
249 break;
250 default:
251 printf("?? (%x)", revid);
252 break;
253 }
254 }
255
256 if (mvebu_soc_family() == MVEBU_SOC_A38X) {
257 switch (revid) {
258 case MV_88F68XX_Z1_ID:
259 puts("Z1");
260 break;
261 case MV_88F68XX_A0_ID:
262 puts("A0");
263 break;
264 default:
265 printf("?? (%x)", revid);
266 break;
267 }
268 }
269
270 get_sar_freq(&sar_freq);
271 printf(" at %d MHz\n", sar_freq.p_clk);
272
273 return 0;
274 }
275 #endif /* CONFIG_DISPLAY_CPUINFO */
276
277 /*
278 * This function initialize Controller DRAM Fastpath windows.
279 * It takes the CS size information from the 0x1500 scratch registers
280 * and sets the correct windows sizes and base addresses accordingly.
281 *
282 * These values are set in the scratch registers by the Marvell
283 * DDR3 training code, which is executed by the BootROM before the
284 * main payload (U-Boot) is executed. This training code is currently
285 * only available in the Marvell U-Boot version. It needs to be
286 * ported to mainline U-Boot SPL at some point.
287 */
update_sdram_window_sizes(void)288 static void update_sdram_window_sizes(void)
289 {
290 u64 base = 0;
291 u32 size, temp;
292 int i;
293
294 for (i = 0; i < SDRAM_MAX_CS; i++) {
295 size = readl((MVEBU_SDRAM_SCRATCH + (i * 8))) & SDRAM_ADDR_MASK;
296 if (size != 0) {
297 size |= ~(SDRAM_ADDR_MASK);
298
299 /* Set Base Address */
300 temp = (base & 0xFF000000ll) | ((base >> 32) & 0xF);
301 writel(temp, MVEBU_SDRAM_BASE + DDR_BASE_CS_OFF(i));
302
303 /*
304 * Check if out of max window size and resize
305 * the window
306 */
307 temp = (readl(MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i)) &
308 ~(SDRAM_ADDR_MASK)) | 1;
309 temp |= (size & SDRAM_ADDR_MASK);
310 writel(temp, MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i));
311
312 base += ((u64)size + 1);
313 } else {
314 /*
315 * Disable window if not used, otherwise this
316 * leads to overlapping enabled windows with
317 * pretty strange results
318 */
319 clrbits_le32(MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i), 1);
320 }
321 }
322 }
323
mmu_disable(void)324 void mmu_disable(void)
325 {
326 asm volatile(
327 "mrc p15, 0, r0, c1, c0, 0\n"
328 "bic r0, #1\n"
329 "mcr p15, 0, r0, c1, c0, 0\n");
330 }
331
332 #ifdef CONFIG_ARCH_CPU_INIT
set_cbar(u32 addr)333 static void set_cbar(u32 addr)
334 {
335 asm("mcr p15, 4, %0, c15, c0" : : "r" (addr));
336 }
337
338 #define MV_USB_PHY_BASE (MVEBU_AXP_USB_BASE + 0x800)
339 #define MV_USB_PHY_PLL_REG(reg) (MV_USB_PHY_BASE | (((reg) & 0xF) << 2))
340 #define MV_USB_X3_BASE(addr) (MVEBU_AXP_USB_BASE | BIT(11) | \
341 (((addr) & 0xF) << 6))
342 #define MV_USB_X3_PHY_CHANNEL(dev, reg) (MV_USB_X3_BASE((dev) + 1) | \
343 (((reg) & 0xF) << 2))
344
setup_usb_phys(void)345 static void setup_usb_phys(void)
346 {
347 int dev;
348
349 /*
350 * USB PLL init
351 */
352
353 /* Setup PLL frequency */
354 /* USB REF frequency = 25 MHz */
355 clrsetbits_le32(MV_USB_PHY_PLL_REG(1), 0x3ff, 0x605);
356
357 /* Power up PLL and PHY channel */
358 setbits_le32(MV_USB_PHY_PLL_REG(2), BIT(9));
359
360 /* Assert VCOCAL_START */
361 setbits_le32(MV_USB_PHY_PLL_REG(1), BIT(21));
362
363 mdelay(1);
364
365 /*
366 * USB PHY init (change from defaults) specific for 40nm (78X30 78X60)
367 */
368
369 for (dev = 0; dev < 3; dev++) {
370 setbits_le32(MV_USB_X3_PHY_CHANNEL(dev, 3), BIT(15));
371
372 /* Assert REG_RCAL_START in channel REG 1 */
373 setbits_le32(MV_USB_X3_PHY_CHANNEL(dev, 1), BIT(12));
374 udelay(40);
375 clrbits_le32(MV_USB_X3_PHY_CHANNEL(dev, 1), BIT(12));
376 }
377 }
378
379 /*
380 * This function is not called from the SPL U-Boot version
381 */
arch_cpu_init(void)382 int arch_cpu_init(void)
383 {
384 struct pl310_regs *const pl310 =
385 (struct pl310_regs *)CONFIG_SYS_PL310_BASE;
386
387 /*
388 * Only with disabled MMU its possible to switch the base
389 * register address on Armada 38x. Without this the SDRAM
390 * located at >= 0x4000.0000 is also not accessible, as its
391 * still locked to cache.
392 */
393 mmu_disable();
394
395 /* Linux expects the internal registers to be at 0xf1000000 */
396 writel(SOC_REGS_PHY_BASE, INTREG_BASE_ADDR_REG);
397 set_cbar(SOC_REGS_PHY_BASE + 0xC000);
398
399 /*
400 * From this stage on, the SoC detection is working. As we have
401 * configured the internal register base to the value used
402 * in the macros / defines in the U-Boot header (soc.h).
403 */
404
405 if (mvebu_soc_family() == MVEBU_SOC_A38X) {
406 /*
407 * To fully release / unlock this area from cache, we need
408 * to flush all caches and disable the L2 cache.
409 */
410 icache_disable();
411 dcache_disable();
412 clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
413 }
414
415 /*
416 * We need to call mvebu_mbus_probe() before calling
417 * update_sdram_window_sizes() as it disables all previously
418 * configured mbus windows and then configures them as
419 * required for U-Boot. Calling update_sdram_window_sizes()
420 * without this configuration will not work, as the internal
421 * registers can't be accessed reliably because of potenial
422 * double mapping.
423 * After updating the SDRAM access windows we need to call
424 * mvebu_mbus_probe() again, as this now correctly configures
425 * the SDRAM areas that are later used by the MVEBU drivers
426 * (e.g. USB, NETA).
427 */
428
429 /*
430 * First disable all windows
431 */
432 mvebu_mbus_probe(NULL, 0);
433
434 if (mvebu_soc_family() == MVEBU_SOC_AXP) {
435 /*
436 * Now the SDRAM access windows can be reconfigured using
437 * the information in the SDRAM scratch pad registers
438 */
439 update_sdram_window_sizes();
440 }
441
442 /*
443 * Finally the mbus windows can be configured with the
444 * updated SDRAM sizes
445 */
446 mvebu_mbus_probe(windows, ARRAY_SIZE(windows));
447
448 if (mvebu_soc_family() == MVEBU_SOC_AXP) {
449 /* Enable GBE0, GBE1, LCD and NFC PUP */
450 clrsetbits_le32(ARMADA_XP_PUP_ENABLE, 0,
451 GE0_PUP_EN | GE1_PUP_EN | LCD_PUP_EN |
452 NAND_PUP_EN | SPI_PUP_EN);
453
454 /* Configure USB PLL and PHYs on AXP */
455 setup_usb_phys();
456 }
457
458 /* Enable NAND and NAND arbiter */
459 clrsetbits_le32(MVEBU_SOC_DEV_MUX_REG, 0, NAND_EN | NAND_ARBITER_EN);
460
461 /* Disable MBUS error propagation */
462 clrsetbits_le32(SOC_COHERENCY_FABRIC_CTRL_REG, MBUS_ERR_PROP_EN, 0);
463
464 return 0;
465 }
466 #endif /* CONFIG_ARCH_CPU_INIT */
467
mvebu_get_nand_clock(void)468 u32 mvebu_get_nand_clock(void)
469 {
470 u32 reg;
471
472 if (mvebu_soc_family() == MVEBU_SOC_A38X)
473 reg = MVEBU_DFX_DIV_CLK_CTRL(1);
474 else
475 reg = MVEBU_CORE_DIV_CLK_CTRL(1);
476
477 return CONFIG_SYS_MVEBU_PLL_CLOCK /
478 ((readl(reg) &
479 NAND_ECC_DIVCKL_RATIO_MASK) >> NAND_ECC_DIVCKL_RATIO_OFFS);
480 }
481
482 /*
483 * SOC specific misc init
484 */
485 #if defined(CONFIG_ARCH_MISC_INIT)
arch_misc_init(void)486 int arch_misc_init(void)
487 {
488 /* Nothing yet, perhaps we need something here later */
489 return 0;
490 }
491 #endif /* CONFIG_ARCH_MISC_INIT */
492
493 #ifdef CONFIG_MMC_SDHCI_MV
board_mmc_init(bd_t * bis)494 int board_mmc_init(bd_t *bis)
495 {
496 mv_sdh_init(MVEBU_SDIO_BASE, 0, 0,
497 SDHCI_QUIRK_32BIT_DMA_ADDR | SDHCI_QUIRK_WAIT_SEND_CMD);
498
499 return 0;
500 }
501 #endif
502
503 #ifdef CONFIG_SCSI_AHCI_PLAT
504 #define AHCI_VENDOR_SPECIFIC_0_ADDR 0xa0
505 #define AHCI_VENDOR_SPECIFIC_0_DATA 0xa4
506
507 #define AHCI_WINDOW_CTRL(win) (0x60 + ((win) << 4))
508 #define AHCI_WINDOW_BASE(win) (0x64 + ((win) << 4))
509 #define AHCI_WINDOW_SIZE(win) (0x68 + ((win) << 4))
510
ahci_mvebu_mbus_config(void __iomem * base)511 static void ahci_mvebu_mbus_config(void __iomem *base)
512 {
513 const struct mbus_dram_target_info *dram;
514 int i;
515
516 dram = mvebu_mbus_dram_info();
517
518 for (i = 0; i < 4; i++) {
519 writel(0, base + AHCI_WINDOW_CTRL(i));
520 writel(0, base + AHCI_WINDOW_BASE(i));
521 writel(0, base + AHCI_WINDOW_SIZE(i));
522 }
523
524 for (i = 0; i < dram->num_cs; i++) {
525 const struct mbus_dram_window *cs = dram->cs + i;
526
527 writel((cs->mbus_attr << 8) |
528 (dram->mbus_dram_target_id << 4) | 1,
529 base + AHCI_WINDOW_CTRL(i));
530 writel(cs->base >> 16, base + AHCI_WINDOW_BASE(i));
531 writel(((cs->size - 1) & 0xffff0000),
532 base + AHCI_WINDOW_SIZE(i));
533 }
534 }
535
ahci_mvebu_regret_option(void __iomem * base)536 static void ahci_mvebu_regret_option(void __iomem *base)
537 {
538 /*
539 * Enable the regret bit to allow the SATA unit to regret a
540 * request that didn't receive an acknowlegde and avoid a
541 * deadlock
542 */
543 writel(0x4, base + AHCI_VENDOR_SPECIFIC_0_ADDR);
544 writel(0x80, base + AHCI_VENDOR_SPECIFIC_0_DATA);
545 }
546
scsi_init(void)547 void scsi_init(void)
548 {
549 printf("MVEBU SATA INIT\n");
550 ahci_mvebu_mbus_config((void __iomem *)MVEBU_SATA0_BASE);
551 ahci_mvebu_regret_option((void __iomem *)MVEBU_SATA0_BASE);
552 ahci_init((void __iomem *)MVEBU_SATA0_BASE);
553 }
554 #endif
555
556 #ifdef CONFIG_USB_XHCI_MVEBU
557 #define USB3_MAX_WINDOWS 4
558 #define USB3_WIN_CTRL(w) (0x0 + ((w) * 8))
559 #define USB3_WIN_BASE(w) (0x4 + ((w) * 8))
560
xhci_mvebu_mbus_config(void __iomem * base,const struct mbus_dram_target_info * dram)561 static void xhci_mvebu_mbus_config(void __iomem *base,
562 const struct mbus_dram_target_info *dram)
563 {
564 int i;
565
566 for (i = 0; i < USB3_MAX_WINDOWS; i++) {
567 writel(0, base + USB3_WIN_CTRL(i));
568 writel(0, base + USB3_WIN_BASE(i));
569 }
570
571 for (i = 0; i < dram->num_cs; i++) {
572 const struct mbus_dram_window *cs = dram->cs + i;
573
574 /* Write size, attributes and target id to control register */
575 writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
576 (dram->mbus_dram_target_id << 4) | 1,
577 base + USB3_WIN_CTRL(i));
578
579 /* Write base address to base register */
580 writel((cs->base & 0xffff0000), base + USB3_WIN_BASE(i));
581 }
582 }
583
board_xhci_enable(fdt_addr_t base)584 int board_xhci_enable(fdt_addr_t base)
585 {
586 const struct mbus_dram_target_info *dram;
587
588 printf("MVEBU XHCI INIT controller @ 0x%lx\n", base);
589
590 dram = mvebu_mbus_dram_info();
591 xhci_mvebu_mbus_config((void __iomem *)base, dram);
592
593 return 0;
594 }
595 #endif
596
enable_caches(void)597 void enable_caches(void)
598 {
599 /* Avoid problem with e.g. neta ethernet driver */
600 invalidate_dcache_all();
601
602 /*
603 * Armada 375 still has some problems with d-cache enabled in the
604 * ethernet driver (mvpp2). So lets keep the d-cache disabled
605 * until this is solved.
606 */
607 if (mvebu_soc_family() != MVEBU_SOC_A375) {
608 /* Enable D-cache. I-cache is already enabled in start.S */
609 dcache_enable();
610 }
611 }
612
v7_outer_cache_enable(void)613 void v7_outer_cache_enable(void)
614 {
615 if (mvebu_soc_family() == MVEBU_SOC_AXP) {
616 struct pl310_regs *const pl310 =
617 (struct pl310_regs *)CONFIG_SYS_PL310_BASE;
618 u32 u;
619
620 /* The L2 cache is already disabled at this point */
621
622 /*
623 * For Aurora cache in no outer mode, enable via the CP15
624 * coprocessor broadcasting of cache commands to L2.
625 */
626 asm volatile("mrc p15, 1, %0, c15, c2, 0" : "=r" (u));
627 u |= BIT(8); /* Set the FW bit */
628 asm volatile("mcr p15, 1, %0, c15, c2, 0" : : "r" (u));
629
630 isb();
631
632 /* Enable the L2 cache */
633 setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
634 }
635 }
636
v7_outer_cache_disable(void)637 void v7_outer_cache_disable(void)
638 {
639 struct pl310_regs *const pl310 =
640 (struct pl310_regs *)CONFIG_SYS_PL310_BASE;
641
642 clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
643 }
644