1# SPDX-License-Identifier: GPL-2.0+ 2# 3# (C) Copyright 2009 4# Marvell Semiconductor <www.marvell.com> 5# Written-by: Prafulla Wadaskar <prafulla@marvell.com> 6# Refer to doc/README.kwbimage for more details about how-to 7# configure and create kirkwood boot images. 8# 9 10# Boot Media configurations 11BOOT_FROM nand 12NAND_ECC_MODE default 13NAND_PAGE_SIZE 0x0800 14 15# SOC registers configuration using bootrom header extension 16# Maximum KWBIMAGE_MAX_CONFIG configurations allowed 17 18# Configure RGMII-0 interface pad voltage to 1.8V 19DATA 0xFFD100e0 0x1b1b1b9b 20 21#Dram initalization for SINGLE x16 CL=5 @ 400MHz 22DATA 0xFFD01400 0x43000c30 # DDR Configuration register 23# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) 24# bit23-14: zero 25# bit24: 1= enable exit self refresh mode on DDR access 26# bit25: 1 required 27# bit29-26: zero 28# bit31-30: 01 29 30DATA 0xFFD01404 0x37543000 # DDR Controller Control Low 31# bit 4: 0=addr/cmd in smame cycle 32# bit 5: 0=clk is driven during self refresh, we don't care for APX 33# bit 6: 0=use recommended falling edge of clk for addr/cmd 34# bit14: 0=input buffer always powered up 35# bit18: 1=cpu lock transaction enabled 36# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 37# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM 38# bit30-28: 3 required 39# bit31: 0=no additional STARTBURST delay 40 41DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) 42# bit3-0: TRAS lsbs 43# bit7-4: TRCD 44# bit11- 8: TRP 45# bit15-12: TWR 46# bit19-16: TWTR 47# bit20: TRAS msb 48# bit23-21: 0x0 49# bit27-24: TRRD 50# bit31-28: TRTP 51 52DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) 53# bit6-0: TRFC 54# bit8-7: TR2R 55# bit10-9: TR2W 56# bit12-11: TW2W 57# bit31-13: zero required 58 59DATA 0xFFD01410 0x000000cc # DDR Address Control 60# bit1-0: 00, Cs0width=x8 61# bit3-2: 11, Cs0size=1Gb 62# bit5-4: 00, Cs1width=x8 63# bit7-6: 11, Cs1size=1Gb 64# bit9-8: 00, Cs2width=nonexistent 65# bit11-10: 00, Cs2size =nonexistent 66# bit13-12: 00, Cs3width=nonexistent 67# bit15-14: 00, Cs3size =nonexistent 68# bit16: 0, Cs0AddrSel 69# bit17: 0, Cs1AddrSel 70# bit18: 0, Cs2AddrSel 71# bit19: 0, Cs3AddrSel 72# bit31-20: 0 required 73 74DATA 0xFFD01414 0x00000000 # DDR Open Pages Control 75# bit0: 0, OpenPage enabled 76# bit31-1: 0 required 77 78DATA 0xFFD01418 0x00000000 # DDR Operation 79# bit3-0: 0x0, DDR cmd 80# bit31-4: 0 required 81 82DATA 0xFFD0141C 0x00000C52 # DDR Mode 83# bit2-0: 2, BurstLen=2 required 84# bit3: 0, BurstType=0 required 85# bit6-4: 4, CL=5 86# bit7: 0, TestMode=0 normal 87# bit8: 0, DLL reset=0 normal 88# bit11-9: 6, auto-precharge write recovery ???????????? 89# bit12: 0, PD must be zero 90# bit31-13: 0 required 91 92DATA 0xFFD01420 0x00000040 # DDR Extended Mode 93# bit0: 0, DDR DLL enabled 94# bit1: 0, DDR drive strenght normal 95# bit2: 0, DDR ODT control lsd (disabled) 96# bit5-3: 000, required 97# bit6: 1, DDR ODT control msb, (disabled) 98# bit9-7: 000, required 99# bit10: 0, differential DQS enabled 100# bit11: 0, required 101# bit12: 0, DDR output buffer enabled 102# bit31-13: 0 required 103 104DATA 0xFFD01424 0x0000F17F # DDR Controller Control High 105# bit2-0: 111, required 106# bit3 : 1 , MBUS Burst Chop disabled 107# bit6-4: 111, required 108# bit7 : 0 109# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz 110# bit9 : 0 , no half clock cycle addition to dataout 111# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals 112# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh 113# bit15-12: 1111 required 114# bit31-16: 0 required 115 116DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) 117DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) 118 119DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 120DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size 121# bit0: 1, Window enabled 122# bit1: 0, Write Protect disabled 123# bit3-2: 00, CS0 hit selected 124# bit23-4: ones, required 125# bit31-24: 0x0F, Size (i.e. 256MB) 126 127DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb 128DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 129 130DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled 131DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled 132 133DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) 134DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) 135# bit1-0: 00, ODT0 controlled by ODT Control (low) register above 136# bit3-2: 01, ODT1 active NEVER! 137# bit31-4: zero, required 138 139DATA 0xFFD0149C 0x0000E803 # CPU ODT Control 140DATA 0xFFD01480 0x00000001 # DDR Initialization Control 141#bit0=1, enable DDR init upon this register write 142 143# End of Header extension 144DATA 0x0 0x0 145