1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Copyright 2016 Freescale Semiconductor, Inc.
4 */
5
6 #include <common.h>
7 #include <fsl_ddr_sdram.h>
8 #include <fsl_ddr_dimm_params.h>
9 #ifdef CONFIG_FSL_DEEP_SLEEP
10 #include <fsl_sleep.h>
11 #endif
12 #include <asm/arch/clock.h>
13 #include "ddr.h"
14
15 DECLARE_GLOBAL_DATA_PTR;
16
fsl_ddr_board_options(memctl_options_t * popts,dimm_params_t * pdimm,unsigned int ctrl_num)17 void fsl_ddr_board_options(memctl_options_t *popts,
18 dimm_params_t *pdimm,
19 unsigned int ctrl_num)
20 {
21 const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
22 ulong ddr_freq;
23
24 if (ctrl_num > 3) {
25 printf("Not supported controller number %d\n", ctrl_num);
26 return;
27 }
28 if (!pdimm->n_ranks)
29 return;
30
31 pbsp = udimms[0];
32
33 /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
34 * freqency and n_banks specified in board_specific_parameters table.
35 */
36 ddr_freq = get_ddr_freq(0) / 1000000;
37 while (pbsp->datarate_mhz_high) {
38 if (pbsp->n_ranks == pdimm->n_ranks) {
39 if (ddr_freq <= pbsp->datarate_mhz_high) {
40 popts->clk_adjust = pbsp->clk_adjust;
41 popts->wrlvl_start = pbsp->wrlvl_start;
42 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
43 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
44 goto found;
45 }
46 pbsp_highest = pbsp;
47 }
48 pbsp++;
49 }
50
51 if (pbsp_highest) {
52 printf("Error: board specific timing not found for %lu MT/s\n",
53 ddr_freq);
54 printf("Trying to use the highest speed (%u) parameters\n",
55 pbsp_highest->datarate_mhz_high);
56 popts->clk_adjust = pbsp_highest->clk_adjust;
57 popts->wrlvl_start = pbsp_highest->wrlvl_start;
58 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
59 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
60 } else {
61 panic("DIMM is not supported by this board");
62 }
63 found:
64 debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
65 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
66
67 popts->data_bus_width = 0; /* 64b data bus */
68 popts->otf_burst_chop_en = 0;
69 popts->burst_length = DDR_BL8;
70 popts->bstopre = 0; /* enable auto precharge */
71
72 popts->half_strength_driver_enable = 0;
73 /*
74 * Write leveling override
75 */
76 popts->wrlvl_override = 1;
77 popts->wrlvl_sample = 0xf;
78
79 /*
80 * Rtt and Rtt_WR override
81 */
82 popts->rtt_override = 0;
83
84 /* Enable ZQ calibration */
85 popts->zq_en = 1;
86
87 popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
88 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
89 DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
90
91 /* optimize cpo for erratum A-009942 */
92 popts->cpo_sample = 0x70;
93 }
94
fsl_initdram(void)95 int fsl_initdram(void)
96 {
97 phys_size_t dram_size;
98
99 #if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
100 gd->ram_size = fsl_ddr_sdram_size();
101
102 return 0;
103 #else
104 puts("Initializing DDR....using SPD\n");
105
106 dram_size = fsl_ddr_sdram();
107 #endif
108
109 #ifdef CONFIG_FSL_DEEP_SLEEP
110 fsl_dp_ddr_restore();
111 #endif
112
113 erratum_a008850_post();
114
115 gd->ram_size = dram_size;
116
117 return 0;
118 }
119