1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Copyright 2009-2013 Freescale Semiconductor, Inc.
4 */
5
6 #include <common.h>
7 #include <command.h>
8 #include <i2c.h>
9 #include <netdev.h>
10 #include <linux/compiler.h>
11 #include <asm/mmu.h>
12 #include <asm/processor.h>
13 #include <asm/immap_85xx.h>
14 #include <asm/fsl_law.h>
15 #include <asm/fsl_serdes.h>
16 #include <asm/fsl_liodn.h>
17 #include <fm_eth.h>
18 #include "t208xrdb.h"
19 #include "cpld.h"
20 #include "../common/vid.h"
21
22 DECLARE_GLOBAL_DATA_PTR;
23
checkboard(void)24 int checkboard(void)
25 {
26 struct cpu_type *cpu = gd->arch.cpu;
27 static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"};
28
29 printf("Board: %sRDB, ", cpu->name);
30 printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
31 CPLD_READ(hw_ver), CPLD_READ(sw_ver));
32
33 #ifdef CONFIG_SDCARD
34 puts("SD/MMC\n");
35 #elif CONFIG_SPIFLASH
36 puts("SPI\n");
37 #else
38 u8 reg;
39
40 reg = CPLD_READ(flash_csr);
41
42 if (reg & CPLD_BOOT_SEL) {
43 puts("NAND\n");
44 } else {
45 reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
46 printf("NOR vBank%d\n", reg);
47 }
48 #endif
49
50 puts("SERDES Reference Clocks:\n");
51 printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
52 printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[0], freq[0]);
53
54 return 0;
55 }
56
board_early_init_r(void)57 int board_early_init_r(void)
58 {
59 const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
60 int flash_esel = find_tlb_idx((void *)flashbase, 1);
61 /*
62 * Remap Boot flash + PROMJET region to caching-inhibited
63 * so that flash can be erased properly.
64 */
65
66 /* Flush d-cache and invalidate i-cache of any FLASH data */
67 flush_dcache();
68 invalidate_icache();
69 if (flash_esel == -1) {
70 /* very unlikely unless something is messed up */
71 puts("Error: Could not find TLB for FLASH BASE\n");
72 flash_esel = 2; /* give our best effort to continue */
73 } else {
74 /* invalidate existing TLB entry for flash + promjet */
75 disable_tlb(flash_esel);
76 }
77
78 set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
79 MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
80 0, flash_esel, BOOKE_PAGESZ_256M, 1);
81
82 /*
83 * Adjust core voltage according to voltage ID
84 * This function changes I2C mux to channel 2.
85 */
86 if (adjust_vdd(0))
87 printf("Warning: Adjusting core voltage failed.\n");
88 return 0;
89 }
90
get_board_sys_clk(void)91 unsigned long get_board_sys_clk(void)
92 {
93 return CONFIG_SYS_CLK_FREQ;
94 }
95
get_board_ddr_clk(void)96 unsigned long get_board_ddr_clk(void)
97 {
98 return CONFIG_DDR_CLK_FREQ;
99 }
100
misc_init_r(void)101 int misc_init_r(void)
102 {
103 u8 reg;
104
105 /* Reset CS4315 PHY */
106 reg = CPLD_READ(reset_ctl);
107 reg |= CPLD_RSTCON_EDC_RST;
108 CPLD_WRITE(reset_ctl, reg);
109
110 return 0;
111 }
112
ft_board_setup(void * blob,bd_t * bd)113 int ft_board_setup(void *blob, bd_t *bd)
114 {
115 phys_addr_t base;
116 phys_size_t size;
117
118 ft_cpu_setup(blob, bd);
119
120 base = env_get_bootm_low();
121 size = env_get_bootm_size();
122
123 fdt_fixup_memory(blob, (u64)base, (u64)size);
124
125 #ifdef CONFIG_PCI
126 pci_of_setup(blob, bd);
127 #endif
128
129 fdt_fixup_liodn(blob);
130 fsl_fdt_fixup_dr_usb(blob, bd);
131
132 #ifdef CONFIG_SYS_DPAA_FMAN
133 fdt_fixup_fman_ethernet(blob);
134 fdt_fixup_board_enet(blob);
135 #endif
136
137 return 0;
138 }
139