1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 modified from SH-IPL+g 4 Renesaso SuperH / Solution Enginge MS775xSE01 BSC setting. 5 6 Support CPU : SH7750/SH7750S/SH7750R/SH7751/SH7751R 7 8 Coyright (c) 2007 Nobuhiro Iwamatsu <iwmatsu@nigauri.org> 9*/ 10 11#include <config.h> 12 13#include <asm/processor.h> 14#include <asm/macro.h> 15 16#ifdef CONFIG_CPU_SH7751 17#define BCR2_D_VALUE 0x2FFC /* Area 1-6 width: 32/32/32/32/32/16 */ 18#define WCR1_D_VALUE 0x02770771 /* DMA:0 A6:2 A3:0 A0:1 Others:15 */ 19#ifdef CONFIG_MARUBUN_PCCARD 20#define WCR2_D_VALUE 0xFFFE4FE7 /* A6:15 A6B:7 A5:15 A5B:7 A4:15 21 A3:2 A2:15 A1:15 A0:6 A0B:7 */ 22#else /* CONFIG_MARUBUN_PCCARD */ 23#define WCR2_D_VALUE 0x7FFE4FE7 /* A6:3 A6B:7 A5:15 A5B:7 A4:15 24 A3:2 A2:15 A1:15 A0:6 A0B:7 */ 25#endif /* CONFIG_MARUBUN_PCCARD */ 26#define WCR3_D_VALUE 0x01777771 /* A6: 0-1 A5: 1-3 A4: 1-3 A3: 1-3 27 A2: 1-3 A1: 1-3 A0: 0-1 */ 28#define RTCOR_D_VALUE 0xA50D /* Write code A5, data 0D (~15us?) */ 29#define SDMR3_ADDRESS 0xFF940088 /* SDMR3 address on 32-bit bus */ 30#define MCR_D1_VALUE 0x100901B4 /* SDRAM 32-bit, CAS/RAS Refresh, .. */ 31#define MCR_D2_VALUE 0x500901B4 /* Same w/MRSET now 1 (mode reg cmd) */ 32#else /* CONFIG_CPU_SH7751 */ 33#define BCR2_D_VALUE 0x2E3C /* Area 1-6 width: 32/32/64/16/32/16 */ 34#define WCR1_D_VALUE 0x02720777 /* DMA:0 A6:2 A4:2 A3:0 Others:15 */ 35#define WCR2_D_VALUE 0xFFFE4FFF /* A6:15 A6B:7 A5:15 A5B:7 A4:15 36 A3:2 A2:15 A1:15 A0:15 A0B:7 */ 37#define WCR3_D_VALUE 0x01717771 /* A6: 0-1 A5: 1-3 A4: 0-1 A3: 1-3 38 A2: 1-3 A1: 1-3 A0: 0-1 */ 39#define RTCOR_D_VALUE 0xA510 /* Write code A5, data 10 (~15us?) */ 40#define SDMR3_ADDRESS 0xFF940110 /* SDMR3 address on 64-bit bus */ 41#define MCR_D1_VALUE 0x8801001C /* SDRAM 64-bit, CAS/RAS Refresh, .. */ 42#define MCR_D2_VALUE 0xC801001C /* Same w/MRSET now 1 (mode reg cmd) */ 43#endif /* CONFIG_CPU_SH7751 */ 44 45 .global lowlevel_init 46 .text 47 .align 2 48 49lowlevel_init: 50 51 write32 CCR_A, CCR_D_DISABLE 52 53init_bsc: 54 write16 FRQCR_A, FRQCR_D 55 56 write32 BCR1_A, BCR1_D 57 58 write16 BCR2_A, BCR2_D 59 60 write32 WCR1_A, WCR1_D 61 62 write32 WCR2_A, WCR2_D 63 64 write32 WCR3_A, WCR3_D 65 66 write32 MCR_A, MCR_D1 67 68 /* Set SDRAM mode */ 69 write8 SDMR3_A, SDMR3_D 70 71 ! Do you need PCMCIA setting? 72 ! If so, please add the lines here... 73 74 write16 RTCNT_A, RTCNT_D 75 76 write16 RTCOR_A, RTCOR_D 77 78 write16 RTCSR_A, RTCSR_D 79 80 write16 RFCR_A, RFCR_D 81 82 /* Wait DRAM refresh 30 times */ 83 mov #30, r3 841: 85 mov.w @r1, r0 86 extu.w r0, r2 87 cmp/hi r3, r2 88 bf 1b 89 90 write32 MCR_A, MCR_D2 91 92 /* Set SDRAM mode */ 93 write8 SDMR3_A, SDMR3_D 94 95 rts 96 nop 97 98 .align 2 99 100CCR_A: .long CCR 101CCR_D_DISABLE: .long 0x0808 102FRQCR_A: .long FRQCR 103FRQCR_D: 104#ifdef CONFIG_CPU_TYPE_R 105 .word 0x0e1a /* 12:3:3 */ 106#else /* CONFIG_CPU_TYPE_R */ 107#ifdef CONFIG_GOOD_SESH4 108 .word 0x00e13 /* 6:2:1 */ 109#else 110 .word 0x00e23 /* 6:1:1 */ 111#endif 112.align 2 113#endif /* CONFIG_CPU_TYPE_R */ 114 115BCR1_A: .long BCR1 116BCR1_D: .long 0x00000008 /* Area 3 SDRAM */ 117BCR2_A: .long BCR2 118BCR2_D: .long BCR2_D_VALUE /* Bus width settings */ 119WCR1_A: .long WCR1 120WCR1_D: .long WCR1_D_VALUE /* Inter-area or turnaround wait states */ 121WCR2_A: .long WCR2 122WCR2_D: .long WCR2_D_VALUE /* Per-area access and burst wait states */ 123WCR3_A: .long WCR3 124WCR3_D: .long WCR3_D_VALUE /* Address setup and data hold cycles */ 125RTCSR_A: .long RTCSR 126RTCSR_D: .word 0xA518 /* RTCSR Write Code A5h Data 18h */ 127.align 2 128RTCNT_A: .long RTCNT 129RTCNT_D: .word 0xA500 /* RTCNT Write Code A5h Data 00h */ 130.align 2 131RTCOR_A: .long RTCOR 132RTCOR_D: .word RTCOR_D_VALUE /* Set refresh time (about 15us) */ 133.align 2 134SDMR3_A: .long SDMR3_ADDRESS 135SDMR3_D: .long 0x00 136MCR_A: .long MCR 137MCR_D1: .long MCR_D1_VALUE 138MCR_D2: .long MCR_D2_VALUE 139RFCR_A: .long RFCR 140RFCR_D: .word 0xA400 /* RFCR Write Code A4h Data 00h */ 141.align 2 142