1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright 2008 Freescale Semiconductor, Inc.
4 */
5
6 #include <common.h>
7 #include <i2c.h>
8
9 #include <fsl_ddr_sdram.h>
10 #include <fsl_ddr_dimm_params.h>
11
fsl_ddr_board_options(memctl_options_t * popts,dimm_params_t * pdimm,unsigned int ctrl_num)12 void fsl_ddr_board_options(memctl_options_t *popts,
13 dimm_params_t *pdimm,
14 unsigned int ctrl_num)
15 {
16 /*
17 * Factors to consider for clock adjust:
18 * - number of chips on bus
19 * - position of slot
20 * - DDR1 vs. DDR2?
21 * - ???
22 *
23 * This needs to be determined on a board-by-board basis.
24 * 0110 3/4 cycle late
25 * 0111 7/8 cycle late
26 */
27 popts->clk_adjust = 7;
28
29 /*
30 * Factors to consider for CPO:
31 * - frequency
32 * - ddr1 vs. ddr2
33 */
34 popts->cpo_override = 10;
35
36 /*
37 * Factors to consider for write data delay:
38 * - number of DIMMs
39 *
40 * 1 = 1/4 clock delay
41 * 2 = 1/2 clock delay
42 * 3 = 3/4 clock delay
43 * 4 = 1 clock delay
44 * 5 = 5/4 clock delay
45 * 6 = 3/2 clock delay
46 */
47 popts->write_data_delay = 3;
48
49 /*
50 * Factors to consider for half-strength driver enable:
51 * - number of DIMMs installed
52 */
53 popts->half_strength_driver_enable = 0;
54 }
55
56 #ifdef CONFIG_SPD_EEPROM
57 /*
58 * Workaround for hardware errata. An i2c address conflict
59 * existed on earlier boards; the workaround moved the DDR
60 * SPD from 0x51 to 0x53. So we try and read 0x53 1st, and
61 * if that fails, then fall back to reading at 0x51.
62 */
get_spd(generic_spd_eeprom_t * spd,u8 i2c_address)63 void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
64 {
65 int ret;
66
67 #ifdef ALT_SPD_EEPROM_ADDRESS
68 if (i2c_address == SPD_EEPROM_ADDRESS) {
69 ret = i2c_read(ALT_SPD_EEPROM_ADDRESS, 0, 1, (uchar *)spd,
70 sizeof(generic_spd_eeprom_t));
71 if (ret == 0)
72 return; /* Good data at 0x53 */
73 memset(spd, 0, sizeof(generic_spd_eeprom_t));
74 }
75 #endif
76 ret = i2c_read(i2c_address, 0, 1, (uchar *)spd,
77 sizeof(generic_spd_eeprom_t));
78 if (ret) {
79 printf("DDR: failed to read SPD from addr %u\n", i2c_address);
80 memset(spd, 0, sizeof(generic_spd_eeprom_t));
81 }
82 }
83
84 #else
85 /*
86 * fixed_sdram init -- doesn't use serial presence detect.
87 * Assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
88 */
fixed_sdram(void)89 phys_size_t fixed_sdram(void)
90 {
91 struct ccsr_ddr __iomem *ddr =
92 (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
93
94 out_be32(&ddr->cs0_bnds, 0x0000007f);
95 out_be32(&ddr->cs1_bnds, 0x008000ff);
96 out_be32(&ddr->cs2_bnds, 0x00000000);
97 out_be32(&ddr->cs3_bnds, 0x00000000);
98
99 out_be32(&ddr->cs0_config, 0x80010101);
100 out_be32(&ddr->cs1_config, 0x80010101);
101 out_be32(&ddr->cs2_config, 0x00000000);
102 out_be32(&ddr->cs3_config, 0x00000000);
103
104 out_be32(&ddr->timing_cfg_3, 0x00000000);
105 out_be32(&ddr->timing_cfg_0, 0x00220802);
106 out_be32(&ddr->timing_cfg_1, 0x38377322);
107 out_be32(&ddr->timing_cfg_2, 0x0fa044C7);
108
109 out_be32(&ddr->sdram_cfg, 0x4300C000);
110 out_be32(&ddr->sdram_cfg_2, 0x24401000);
111
112 out_be32(&ddr->sdram_mode, 0x23C00542);
113 out_be32(&ddr->sdram_mode_2, 0x00000000);
114
115 out_be32(&ddr->sdram_interval, 0x05080100);
116 out_be32(&ddr->sdram_md_cntl, 0x00000000);
117 out_be32(&ddr->sdram_data_init, 0x00000000);
118 out_be32(&ddr->sdram_clk_cntl, 0x03800000);
119 asm("sync;isync;msync");
120 udelay(500);
121
122 #ifdef CONFIG_DDR_ECC
123 /* Enable ECC checking */
124 out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
125 #else
126 out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
127 #endif
128
129 return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
130 }
131 #endif
132