1TF-A Build Instructions for Marvell Platforms 2============================================= 3 4This section describes how to compile the Trusted Firmware-A (TF-A) project for Marvell's platforms. 5 6Build Instructions 7------------------ 8(1) Set the cross compiler 9 10 .. code:: shell 11 12 > export CROSS_COMPILE=/path/to/toolchain/aarch64-linux-gnu- 13 14(2) Set path for FIP images: 15 16Set U-Boot image path (relatively to TF-A root or absolute path) 17 18 .. code:: shell 19 20 > export BL33=path/to/u-boot.bin 21 22For example: if U-Boot project (and its images) is located at ``~/project/u-boot``, 23BL33 should be ``~/project/u-boot/u-boot.bin`` 24 25 .. note:: 26 27 *u-boot.bin* should be used and not *u-boot-spl.bin* 28 29Set MSS/SCP image path (mandatory only for Armada80x0) 30 31 .. code:: shell 32 33 > export SCP_BL2=path/to/mrvl_scp_bl2*.img 34 35(3) Armada-37x0 build requires WTP tools installation. 36 37See below in the section "Tools and external components installation". 38Install ARM 32-bit cross compiler, which is required for building WTMI image for CM3 39 40 .. code:: shell 41 42 > sudo apt-get install gcc-arm-linux-gnueabi 43 44(4) Clean previous build residuals (if any) 45 46 .. code:: shell 47 48 > make distclean 49 50(5) Build TF-A 51 52There are several build options: 53 54- DEBUG 55 56 Default is without debug information (=0). in order to enable it use ``DEBUG=1``. 57 Must be disabled when building UART recovery images due to current console driver 58 implementation that is not compatible with Xmodem protocol used for boot image download. 59 60- LOG_LEVEL 61 62 Defines the level of logging which will be purged to the default output port. 63 64 LOG_LEVEL_NONE 0 65 LOG_LEVEL_ERROR 10 66 LOG_LEVEL_NOTICE 20 67 LOG_LEVEL_WARNING 30 68 LOG_LEVEL_INFO 40 69 LOG_LEVEL_VERBOSE 50 70 71- USE_COHERENT_MEM 72 73 This flag determines whether to include the coherent memory region in the 74 BL memory map or not. 75 76- LLC_ENABLE 77 78 Flag defining the LLC (L3) cache state. The cache is enabled by default (``LLC_ENABLE=1``). 79 80- MARVELL_SECURE_BOOT 81 82 Build trusted(=1)/non trusted(=0) image, default is non trusted. 83 84- BLE_PATH 85 86 Points to BLE (Binary ROM extension) sources folder. Only required for A8K builds. 87 The parameter is optional, its default value is ``plat/marvell/a8k/common/ble``. 88 89- MV_DDR_PATH 90 91 For A7/8K, use this parameter to point to mv_ddr driver sources to allow BLE build. For A37x0, 92 it is used for ddr_tool build. 93 94 Usage example: MV_DDR_PATH=path/to/mv_ddr 95 96 The parameter is optional for A7/8K, when this parameter is not set, the mv_ddr 97 sources are expected to be located at: drivers/marvell/mv_ddr. However, the parameter 98 is necessary for A37x0. 99 100 For the mv_ddr source location, check the section "Tools and external components installation" 101 102- DDR_TOPOLOGY 103 104 For Armada37x0 only, the DDR topology map index/name, default is 0. 105 106 Supported Options: 107 - DDR3 1CS (0): DB-88F3720-DDR3-Modular (512MB); EspressoBIN (512MB) 108 - DDR4 1CS (1): DB-88F3720-DDR4-Modular (512MB) 109 - DDR3 2CS (2): EspressoBIN V3-V5 (1GB) 110 - DDR4 2CS (3): DB-88F3720-DDR4-Modular (4GB) 111 - DDR3 1CS (4): DB-88F3720-DDR3-Modular (1GB) 112 - DDR4 1CS (5): EspressoBin V7 (1GB) 113 - DDR4 2CS (6): EspressoBin V7 (2GB) 114 - CUSTOMER (CUST): Customer board, DDR3 1CS 512MB 115 116- CLOCKSPRESET 117 118 For Armada37x0 only, the clock tree configuration preset including CPU and DDR frequency, 119 default is CPU_800_DDR_800. 120 121 - CPU_600_DDR_600 - CPU at 600 MHz, DDR at 600 MHz 122 - CPU_800_DDR_800 - CPU at 800 MHz, DDR at 800 MHz 123 - CPU_1000_DDR_800 - CPU at 1000 MHz, DDR at 800 MHz 124 - CPU_1200_DDR_750 - CPU at 1200 MHz, DDR at 750 MHz 125 126- BOOTDEV 127 128 For Armada37x0 only, the flash boot device, default is ``SPINOR``. 129 130 Currently, Armada37x0 only supports ``SPINOR``, ``SPINAND``, ``EMMCNORM`` and ``SATA``: 131 132 - SPINOR - SPI NOR flash boot 133 - SPINAND - SPI NAND flash boot 134 - EMMCNORM - eMMC Download Mode 135 136 Download boot loader or program code from eMMC flash into CM3 or CA53 137 Requires full initialization and command sequence 138 139 - SATA - SATA device boot 140 141- PARTNUM 142 143 For Armada37x0 only, the boot partition number, default is 0. 144 145 To boot from eMMC, the value should be aligned with the parameter in 146 U-Boot with name of ``CONFIG_SYS_MMC_ENV_PART``, whose value by default is 147 1. For details about CONFIG_SYS_MMC_ENV_PART, please refer to the U-Boot 148 build instructions. 149 150- WTMI_IMG 151 152 For Armada37x0 only, the path of the WTMI image can point to an image which 153 does nothing, an image which supports EFUSE or a customized CM3 firmware 154 binary. The default image is wtmi.bin that built from sources in WTP 155 folder, which is the next option. If the default image is OK, then this 156 option should be skipped. 157 158- WTP 159 160 For Armada37x0 only, use this parameter to point to wtptools source code 161 directory, which can be found as a3700_utils.zip in the release. Usage 162 example: ``WTP=/path/to/a3700_utils`` 163 164 For example, in order to build the image in debug mode with log level up to 'notice' level run 165 166 .. code:: shell 167 168 > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 PLAT=<MARVELL_PLATFORM> all fip 169 170 And if we want to build a Armada37x0 image in debug mode with log level up to 'notice' level, 171 the image has the preset CPU at 1000 MHz, preset DDR3 at 800 MHz, the DDR topology of DDR4 2CS, 172 the image boot from SPI NOR flash partition 0, and the image is non trusted in WTP, the command 173 line is as following 174 175 .. code:: shell 176 177 > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 CLOCKSPRESET=CPU_1000_DDR_800 \ 178 MARVELL_SECURE_BOOT=0 DDR_TOPOLOGY=3 BOOTDEV=SPINOR PARTNUM=0 PLAT=a3700 all fip 179 180 Supported MARVELL_PLATFORM are: 181 - a3700 (for both A3720 DB and EspressoBin) 182 - a70x0 183 - a70x0_amc (for AMC board) 184 - a80x0 185 - a80x0_mcbin (for MacciatoBin) 186 187Special Build Flags 188-------------------- 189 190- PLAT_RECOVERY_IMAGE_ENABLE 191 When set this option to enable secondary recovery function when build atf. 192 In order to build UART recovery image this operation should be disabled for 193 a70x0 and a80x0 because of hardware limitation (boot from secondary image 194 can interrupt UART recovery process). This MACRO definition is set in 195 ``plat/marvell/a8k/common/include/platform_def.h`` file. 196 197For more information about build options, please refer to the 198:ref:`Build Options` document. 199 200 201Build output 202------------ 203Marvell's TF-A compilation generates 7 files: 204 205 - ble.bin - BLe image 206 - bl1.bin - BL1 image 207 - bl2.bin - BL2 image 208 - bl31.bin - BL31 image 209 - fip.bin - FIP image (contains BL2, BL31 & BL33 (U-Boot) images) 210 - boot-image.bin - TF-A image (contains BL1 and FIP images) 211 - flash-image.bin - Image which contains boot-image.bin and SPL image. 212 Should be placed on the boot flash/device. 213 214 215Tools and external components installation 216------------------------------------------ 217 218Armada37x0 Builds require installation of 3 components 219~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 220 221(1) ARM cross compiler capable of building images for the service CPU (CM3). 222 This component is usually included in the Linux host packages. 223 On Debian/Ubuntu hosts the default GNU ARM tool chain can be installed 224 using the following command 225 226 .. code:: shell 227 228 > sudo apt-get install gcc-arm-linux-gnueabi 229 230 Only if required, the default tool chain prefix ``arm-linux-gnueabi-`` can be 231 overwritten using the environment variable ``CROSS_CM3``. 232 Example for BASH shell 233 234 .. code:: shell 235 236 > export CROSS_CM3=/opt/arm-cross/bin/arm-linux-gnueabi 237 238(2) DDR initialization library sources (mv_ddr) available at the following repository 239 (use the "mv_ddr-armada-atf-mainline" branch): 240 241 https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git 242 243(3) Armada3700 tools available at the following repository (use the latest release branch): 244 245 https://github.com/MarvellEmbeddedProcessors/A3700-utils-marvell.git 246 247Armada70x0 and Armada80x0 Builds require installation of an additional component 248~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 249 250(1) DDR initialization library sources (mv_ddr) available at the following repository 251 (use the "mv_ddr-armada-atf-mainline" branch): 252 253 https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git 254