1 /*
2 * Copyright (C) 2018 Marvell International Ltd.
3 *
4 * SPDX-License-Identifier: BSD-3-Clause
5 * https://spdx.org/licenses
6 */
7
8 #include <arch_helpers.h>
9 #include <common/debug.h>
10 #include <drivers/mentor/mi2cv.h>
11 #include <lib/mmio.h>
12
13 #include <mv_ddr_if.h>
14 #include <mvebu_def.h>
15 #include <plat_marvell.h>
16
17 #define MVEBU_AP_MPP_CTRL0_7_REG MVEBU_AP_MPP_REGS(0)
18 #define MVEBU_AP_MPP_CTRL4_OFFS 16
19 #define MVEBU_AP_MPP_CTRL5_OFFS 20
20 #define MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA 0x3
21 #define MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA 0x3
22
23 #define MVEBU_CP_MPP_CTRL37_OFFS 20
24 #define MVEBU_CP_MPP_CTRL38_OFFS 24
25 #define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA 0x2
26 #define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA 0x2
27
28 #define MVEBU_MPP_CTRL_MASK 0xf
29
30 /*
31 * This struct provides the DRAM training code with
32 * the appropriate board DRAM configuration
33 */
34 static struct mv_ddr_topology_map board_topology_map = {
35 /* MISL board with 1CS 8Gb x4 devices of Micron 2400T */
36 DEBUG_LEVEL_ERROR,
37 0x1, /* active interfaces */
38 /* cs_mask, mirror, dqs_swap, ck_swap X subphys */
39 { { { {0x1, 0x0, 0, 0}, /* FIXME: change the cs mask for all 64 bit */
40 {0x1, 0x0, 0, 0},
41 {0x1, 0x0, 0, 0},
42 {0x1, 0x0, 0, 0},
43 {0x1, 0x0, 0, 0},
44 {0x1, 0x0, 0, 0},
45 {0x1, 0x0, 0, 0},
46 {0x1, 0x0, 0, 0},
47 {0x1, 0x0, 0, 0} },
48 /* TODO: double check if the speed bin is 2400T */
49 SPEED_BIN_DDR_2400T, /* speed_bin */
50 MV_DDR_DEV_WIDTH_8BIT, /* sdram device width */
51 MV_DDR_DIE_CAP_8GBIT, /* die capacity */
52 MV_DDR_FREQ_SAR, /* frequency */
53 0, 0, /* cas_l, cas_wl */
54 MV_DDR_TEMP_LOW} }, /* temperature */
55 MV_DDR_64BIT_ECC_PUP8_BUS_MASK, /* subphys mask */
56 MV_DDR_CFG_SPD, /* ddr configuration data source */
57 { {0} }, /* raw spd data */
58 {0}, /* timing parameters */
59 { /* electrical configuration */
60 { /* memory electrical configuration */
61 MV_DDR_RTT_NOM_PARK_RZQ_DISABLE, /* rtt_nom */
62 {
63 MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
64 MV_DDR_RTT_NOM_PARK_RZQ_DIV1 /* rtt_park 2cs */
65 },
66 {
67 MV_DDR_RTT_WR_DYN_ODT_OFF, /* rtt_wr 1cs */
68 MV_DDR_RTT_WR_RZQ_DIV2 /* rtt_wr 2cs */
69 },
70 MV_DDR_DIC_RZQ_DIV7 /* dic */
71 },
72 { /* phy electrical configuration */
73 MV_DDR_OHM_30, /* data_drv_p */
74 MV_DDR_OHM_30, /* data_drv_n */
75 MV_DDR_OHM_30, /* ctrl_drv_p */
76 MV_DDR_OHM_30, /* ctrl_drv_n */
77 {
78 MV_DDR_OHM_60, /* odt_p 1cs */
79 MV_DDR_OHM_120 /* odt_p 2cs */
80 },
81 {
82 MV_DDR_OHM_60, /* odt_n 1cs */
83 MV_DDR_OHM_120 /* odt_n 2cs */
84 },
85 },
86 { /* mac electrical configuration */
87 MV_DDR_ODT_CFG_NORMAL, /* odtcfg_pattern */
88 MV_DDR_ODT_CFG_ALWAYS_ON, /* odtcfg_write */
89 MV_DDR_ODT_CFG_NORMAL, /* odtcfg_read */
90 },
91 }
92 };
93
mv_ddr_topology_map_get(void)94 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
95 {
96 /* Return the board topology as defined in the board code */
97 return &board_topology_map;
98 }
99
mpp_config(void)100 static void mpp_config(void)
101 {
102 uintptr_t reg;
103 uint32_t val;
104
105 reg = MVEBU_CP_MPP_REGS(0, 4);
106 /* configure CP0 MPP 37 and 38 to i2c */
107 val = mmio_read_32(reg);
108 val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
109 (MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
110 val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA <<
111 MVEBU_CP_MPP_CTRL37_OFFS) |
112 (MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA <<
113 MVEBU_CP_MPP_CTRL38_OFFS);
114 mmio_write_32(reg, val);
115 }
116
117 /*
118 * This function may modify the default DRAM parameters
119 * based on information received from SPD or bootloader
120 * configuration located on non volatile storage
121 */
plat_marvell_dram_update_topology(void)122 void plat_marvell_dram_update_topology(void)
123 {
124 struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
125
126 INFO("Gathering DRAM information\n");
127
128 if (tm->cfg_src == MV_DDR_CFG_SPD) {
129 /* configure MPPs to enable i2c */
130 mpp_config();
131
132 /* initialize i2c */
133 i2c_init((void *)MVEBU_CP0_I2C_BASE);
134
135 /* select SPD memory page 0 to access DRAM configuration */
136 i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 1);
137
138 /* read data from spd */
139 i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
140 sizeof(tm->spd_data.all_bytes));
141 }
142 }
143