• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1/* SPDX-License-Identifier: GPL-2.0+ */
2/*
3 * Copyright (C) 2011 Andes Technology Corporation
4 * Shawn Lin, Andes Technology Corporation <nobuhiro@andestech.com>
5 * Macpaul Lin, Andes Technology Corporation <macpaul@andestech.com>
6 */
7
8.pic
9
10.text
11
12#include <common.h>
13#include <config.h>
14
15#include <asm/macro.h>
16#include <generated/asm-offsets.h>
17
18/*
19 * parameters for the SDRAM controller
20 */
21#define SDMC_TP1_A		(CONFIG_FTSDMC021_BASE + FTSDMC021_TP1)
22#define SDMC_TP2_A		(CONFIG_FTSDMC021_BASE + FTSDMC021_TP2)
23#define SDMC_CR1_A		(CONFIG_FTSDMC021_BASE + FTSDMC021_CR1)
24#define SDMC_CR2_A		(CONFIG_FTSDMC021_BASE + FTSDMC021_CR2)
25#define SDMC_B0_BSR_A		(CONFIG_FTSDMC021_BASE + FTSDMC021_BANK0_BSR)
26#define SDMC_B1_BSR_A		(CONFIG_FTSDMC021_BASE + FTSDMC021_BANK1_BSR)
27
28#define SDMC_TP1_D		CONFIG_SYS_FTSDMC021_TP1
29#define SDMC_TP2_D		CONFIG_SYS_FTSDMC021_TP2
30#define SDMC_CR1_D		CONFIG_SYS_FTSDMC021_CR1
31#define SDMC_CR2_D		CONFIG_SYS_FTSDMC021_CR2
32
33#define SDMC_B0_BSR_D		CONFIG_SYS_FTSDMC021_BANK0_BSR
34#define SDMC_B1_BSR_D		CONFIG_SYS_FTSDMC021_BANK1_BSR
35
36
37/*
38 * for Orca and Emerald
39 */
40#define BOARD_ID_REG		0x104
41#define BOARD_ID_FAMILY_MASK 	0xfff000
42#define BOARD_ID_FAMILY_V5   	0x556000
43#define BOARD_ID_FAMILY_K7   	0x74b000
44
45/*
46 * parameters for the static memory controller
47 */
48#define SMC_BANK0_CR_A		(CONFIG_FTSMC020_BASE + FTSMC020_BANK0_CR)
49#define SMC_BANK0_TPR_A		(CONFIG_FTSMC020_BASE + FTSMC020_BANK0_TPR)
50
51#define SMC_BANK0_CR_D		FTSMC020_BANK0_LOWLV_CONFIG
52#define SMC_BANK0_TPR_D		FTSMC020_BANK0_LOWLV_TIMING
53
54/*
55 * parameters for the ahbc controller
56 */
57#define AHBC_CR_A		(CONFIG_FTAHBC020S_BASE + FTAHBC020S_CR)
58#define AHBC_BSR6_A	(CONFIG_FTAHBC020S_BASE + FTAHBC020S_SLAVE_BSR_6)
59
60/*
61 * for Orca and Emerald
62 */
63#define AHBC_BSR4_A	(CONFIG_FTAHBC020S_BASE + FTAHBC020S_SLAVE_BSR_4)
64#define AHBC_BSR6_D		CONFIG_SYS_FTAHBC020S_SLAVE_BSR_6
65
66/*
67 * parameters for the pmu controoler
68 */
69#define PMU_PDLLCR0_A		(CONFIG_FTPMU010_BASE + FTPMU010_PDLLCR0)
70
71/*
72 * numeric 7 segment display
73 */
74.macro	led, num
75	write32	CONFIG_DEBUG_LED, \num
76.endm
77
78/*
79 * Waiting for SDRAM to set up
80 */
81.macro	wait_sdram
82	li	$r0, CONFIG_FTSDMC021_BASE
831:
84	lwi	$r1, [$r0+FTSDMC021_CR2]
85	bnez	$r1, 1b
86.endm
87
88.globl	mem_init
89mem_init:
90	move	$r11, $lp
91
92	/*
93	 * mem_init:
94	 *	There are 2 bank connected to FTSMC020 on AG101
95	 *	BANK0: FLASH/ROM (SW5, J16), BANK1: OnBoard SDRAM.
96	 *	we need to set onboard SDRAM before remap and relocation.
97	 */
98	led	0x01
99
100  /*
101   * for Orca and Emerald
102   * disable write protection and reset bank size
103   */
104	li	$r0, SMC_BANK0_CR_A
105	lwi $r1, [$r0+#0x00]
106	ori $r1, $r1, 0x8f0
107	xori $r1, $r1, 0x8f0
108	/* check board */
109	li      $r3, CONFIG_FTPMU010_BASE + BOARD_ID_REG
110  lwi     $r3, [$r3]
111  li      $r4, BOARD_ID_FAMILY_MASK
112  and     $r3, $r3, $r4
113  li      $r4, BOARD_ID_FAMILY_K7
114  xor     $r4, $r3, $r4
115  beqz    $r4, use_flash_16bit_boot
116	/* 32-bit mode */
117use_flash_32bit_boot:
118	ori     $r1, $r1, 0x50
119  li      $r2, 0x00151151
120  j       sdram_b0_cr
121	/* 16-bit mode */
122use_flash_16bit_boot:
123  ori     $r1, $r1, 0x60
124  li      $r2, 0x00153153
125	/* SRAM bank0 config */
126sdram_b0_cr:
127  swi     $r1, [$r0+#0x00]
128  swi     $r2, [$r0+#0x04]
129
130	/* config AHB Controller */
131	led	0x02
132
133	/*
134	 * config PMU controller
135	 */
136	/* ftpmu010_dlldis_disable, must do it in lowleve_init */
137	led	0x03
138	setbf32	PMU_PDLLCR0_A, FTPMU010_PDLLCR0_DLLDIS		! 0x00010000
139
140	/*
141	 * config SDRAM controller
142	 */
143	led	0x04
144	write32	SDMC_TP1_A, SDMC_TP1_D				! 0x00011312
145	led	0x05
146	write32	SDMC_TP2_A, SDMC_TP2_D				! 0x00480180
147	led	0x06
148	write32	SDMC_CR1_A, SDMC_CR1_D				! 0x00002326
149
150	led	0x07
151	write32	SDMC_CR2_A, FTSDMC021_CR2_IPREC			! 0x00000010
152	wait_sdram
153
154	led	0x08
155	write32	SDMC_CR2_A, FTSDMC021_CR2_ISMR			! 0x00000004
156	wait_sdram
157
158	led	0x09
159	write32	SDMC_CR2_A, FTSDMC021_CR2_IREF			! 0x00000008
160	wait_sdram
161
162	led	0x0a
163	move	$lp, $r11
164	ret
165
166
167#ifndef CONFIG_SKIP_LOWLEVEL_INIT
168
169.globl	lowlevel_init
170lowlevel_init:
171	move	$r10, $lp
172	led	0x10
173	jal	remap
174#if (defined(NDS32_EXT_FPU_DP) || defined(NDS32_EXT_FPU_SP))
175	led	0x1f
176	jal	enable_fpu
177#endif
178	led	0x20
179	ret	$r10
180
181remap:
182	move	$r11, $lp
183#ifdef __NDS32_N1213_43U1H__	/* NDS32 V0 ISA - AG101 Only */
184	bal	2f
185relo_base:
186	move	$r0, $lp
187#else
188relo_base:
189	mfusr	$r0, $pc
190#endif /* __NDS32_N1213_43U1H__ */
191
192	/* Remapping */
193	led	0x1a
194	write32	SDMC_B0_BSR_A, SDMC_B0_BSR_D		! 0x00001800
195	write32	SDMC_B1_BSR_A, SDMC_B1_BSR_D		! 0x00001880
196
197	/* clear empty BSR registers */
198	led	0x1b
199	li	$r4, CONFIG_FTSDMC021_BASE
200	li	$r5, 0x0
201	swi	$r5, [$r4 + FTSDMC021_BANK2_BSR]
202	swi	$r5, [$r4 + FTSDMC021_BANK3_BSR]
203
204#ifdef CONFIG_MEM_REMAP
205	/*
206	 * Copy ROM code to SDRAM base for memory remap layout.
207	 * This is not the real relocation, the real relocation is the function
208	 * relocate_code() is start.S which supports the systems is memory
209	 * remapped or not.
210	 */
211	/*
212	 * Doing memory remap is essential for preparing some non-OS or RTOS
213	 * applications.
214	 *
215	 * This is also a must on ADP-AG101 board.
216	 * The reason is because the ROM/FLASH circuit on PCB board.
217	 * AG101-A0 board has 2 jumpers MA17 and SW5 to configure which
218	 * ROM/FLASH is used to boot.
219	 *
220	 * When SW5 = "0101", MA17 = LO, the ROM is connected to BANK0,
221	 * and the FLASH is connected to BANK1.
222	 * When SW5 = "1010", MA17 = HI, the ROM is disabled (still at BANK0),
223	 * and the FLASH is connected to BANK0.
224	 * It will occur problem when doing flash probing if the flash is at
225	 * BANK0 (0x00000000) while memory remapping was skipped.
226	 *
227	 * Other board like ADP-AG101P may not enable this since there is only
228	 * a FLASH connected to bank0.
229	 */
230	led	0x11
231   /*
232    * for Orca and Emerald
233    * read sdram base address automatically
234    */
235	li	$r5, AHBC_BSR6_A
236	lwi $r8, [$r5]
237	li	$r4, 0xfff00000   /* r4 = bank6 base */
238	and $r4, $r4, $r8
239
240	la	$r5, _start@GOTOFF
241	la  $r6, _end@GOTOFF
2421:
243	lwi.p	$r7, [$r5], #4
244	swi.p	$r7, [$r4], #4
245	blt	$r5, $r6, 1b
246
247	/* set remap bit */
248	/*
249	 * MEM remap bit is operational
250	 * - use it to map writeable memory at 0x00000000, in place of flash
251	 * - before remap: flash/rom 0x00000000, sdram: 0x10000000-0x4fffffff
252	 * - after  remap: flash/rom 0x80000000, sdram: 0x00000000
253	 */
254	led	0x1c
255	write32 SDMC_B0_BSR_A, 0x00001000
256	write32 SDMC_B1_BSR_A, 0x00001200
257	li $r5, CONFIG_SYS_TEXT_BASE	/* flash base address */
258	add $r11, $r11, $r5	/* add flash address offset for ret */
259	add $r10, $r10, $r5
260	move $lp, $r11
261	setbf15	AHBC_CR_A, FTAHBC020S_CR_REMAP		! 0x1
262
263  /*
264   * for Orca and Emerald
265   * extend sdram size from 256MB to 2GB
266   */
267	li	$r5, AHBC_BSR6_A
268	lwi $r6, [$r5]
269	li  $r4, 0xfff0ffff
270	and $r6 ,$r4, $r6
271	li	$r4, 0x000b0000
272	or  $r6, $r4, $r6
273	swi	$r6, [$r5]
274
275  /*
276   * for Orca and Emerald
277   * extend rom base from 256MB to 2GB
278   */
279	li	$r4, AHBC_BSR4_A
280	lwi $r5, [$r4]
281	li	$r6, 0xffffff
282	and $r5, $r5, $r6
283	li  $r6, 0x80000000
284	or  $r5, $r5, $r6
285	swi $r5,	[$r4]
286#endif /* #ifdef CONFIG_MEM_REMAP */
287	move $lp, $r11
2882:
289	ret
290
291	/*
292	 * enable_fpu:
293	 *  Some of Andes CPU version support FPU coprocessor, if so,
294	 *  and toolchain support FPU instruction set, we should enable it.
295	 */
296#if (defined(NDS32_EXT_FPU_DP) || defined(NDS32_EXT_FPU_SP))
297enable_fpu:
298	mfsr    $r0, $CPU_VER     /* enable FPU if it exists */
299	srli    $r0, $r0, 3
300	andi    $r0, $r0, 1
301	beqz    $r0, 1f           /* skip if no COP */
302	mfsr    $r0, $FUCOP_EXIST
303	srli    $r0, $r0, 31
304	beqz    $r0, 1f           /* skip if no FPU */
305	mfsr    $r0, $FUCOP_CTL
306	ori     $r0, $r0, 1
307	mtsr    $r0, $FUCOP_CTL
3081:
309	ret
310#endif
311
312.globl show_led
313show_led:
314    li      $r8, (CONFIG_DEBUG_LED)
315    swi     $r7, [$r8]
316    ret
317#endif /* #ifndef CONFIG_SKIP_LOWLEVEL_INIT */
318