• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1The following properties are common to the Ethernet controllers:
2
3NOTE: All 'phy*' properties documented below are Ethernet specific. For the
4generic PHY 'phys' property, see
5Documentation/devicetree/bindings/phy/phy-bindings.txt.
6
7- local-mac-address: array of 6 bytes, specifies the MAC address that was
8  assigned to the network device;
9- mac-address: array of 6 bytes, specifies the MAC address that was last used by
10  the boot program; should be used in cases where the MAC address assigned to
11  the device by the boot program is different from the "local-mac-address"
12  property;
13- nvmem-cells: phandle, reference to an nvmem node for the MAC address;
14- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used;
15- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
16- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
17  the maximum frame size (there's contradiction in the Devicetree
18  Specification).
19- phy-mode: string, operation mode of the PHY interface. This is now a de-facto
20  standard property; supported values are:
21  * "internal"
22  * "mii"
23  * "gmii"
24  * "sgmii"
25  * "qsgmii"
26  * "tbi"
27  * "rev-mii"
28  * "rmii"
29  * "rgmii" (RX and TX delays are added by the MAC when required)
30  * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the
31     MAC should not add the RX or TX delays in this case)
32  * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
33     should not add an RX delay in this case)
34  * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC
35     should not add an TX delay in this case)
36  * "rtbi"
37  * "smii"
38  * "xgmii"
39  * "trgmii"
40  * "2000base-x",
41  * "2500base-x",
42  * "rxaui"
43  * "xaui"
44  * "10gbase-kr" (10GBASE-KR, XFI, SFI)
45- phy-connection-type: the same as "phy-mode" property but described in the
46  Devicetree Specification;
47- phy-handle: phandle, specifies a reference to a node representing a PHY
48  device; this property is described in the Devicetree Specification and so
49  preferred;
50- phy: the same as "phy-handle" property, not recommended for new bindings.
51- phy-device: the same as "phy-handle" property, not recommended for new
52  bindings.
53- rx-fifo-depth: the size of the controller's receive fifo in bytes. This
54  is used for components that can have configurable receive fifo sizes,
55  and is useful for determining certain configuration settings such as
56  flow control thresholds.
57- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This
58  is used for components that can have configurable fifo sizes.
59- managed: string, specifies the PHY management type. Supported values are:
60  "auto", "in-band-status". "auto" is the default, it usess MDIO for
61  management if fixed-link is not specified.
62
63Child nodes of the Ethernet controller are typically the individual PHY devices
64connected via the MDIO bus (sometimes the MDIO bus controller is separate).
65They are described in the phy.txt file in this same directory.
66For non-MDIO PHY management see fixed-link.txt.
67