• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * (C) Copyright 2016
4  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
5  *
6  * Based on:
7  * am335x_evm.h
8  *
9  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
10  */
11 
12 #ifndef __CONFIG_AM335X_SHC_H
13 #define __CONFIG_AM335X_SHC_H
14 
15 #include <configs/ti_am335x_common.h>
16 
17 /* settings we don;t want on this board */
18 #undef CONFIG_CMD_SPI
19 
20 #define CONFIG_CMD_CACHE
21 
22 #ifndef CONFIG_SPL_BUILD
23 # define CONFIG_TIMESTAMP
24 #endif
25 
26 #define CONFIG_SYS_BOOTM_LEN		(16 << 20)
27 
28 /* Clock Defines */
29 #define V_OSCK				24000000  /* Clock output from T2 */
30 #define V_SCLK				(V_OSCK)
31 
32 /*
33  * in case of SD Card or Network boot we want to have a possibility to
34  * debrick the shc, therefore do not read environment from eMMC
35  */
36 #if defined(CONFIG_SHC_SDBOOT) || defined(CONFIG_SHC_NETBOOT)
37 #define CONFIG_SYS_MMC_ENV_DEV		0
38 #else
39 #define CONFIG_SYS_MMC_ENV_DEV		1
40 #endif
41 
42 /*
43  * Info when using boot partitions: As environment resides within first
44  * 128 kB, MLO must start at 128 kB == 0x20000
45  * ENV at MMC Boot0 Partition - 0/Undefined=user, 1=boot0, 2=boot1,
46  * 4..7=general0..3
47  */
48 
49 #define CONFIG_HSMMC2_8BIT
50 
51 #ifndef CONFIG_SHC_ICT
52 /*
53  * In builds other than ICT, reset to retry after timeout
54  * Define a timeout after which a stopped bootloader continues autoboot
55  * (only works with CONFIG_RESET_TO_RETRY)
56  */
57 # define CONFIG_BOOT_RETRY_TIME 30
58 # define CONFIG_RESET_TO_RETRY
59 #endif
60 
61 #ifndef CONFIG_SPL_BUILD
62 #define CONFIG_EXTRA_ENV_SETTINGS \
63 	"loadaddr=0x80200000\0" \
64 	"kloadaddr=0x84000000\0" \
65 	"fdtaddr=0x85000000\0" \
66 	"fdt_high=0xffffffff\0" \
67 	"rdaddr=0x81000000\0" \
68 	"bootfile=uImage\0" \
69 	"fdtfile=am335x-shc.dtb\0" \
70 	"verify=no\0" \
71 	"serverip=10.55.152.184\0" \
72 	"rootpath=/srv/nfs/shc-rootfs\0" \
73 	"console=ttyO0,115200n8\0" \
74 	"optargs=quiet\0" \
75 	"mmcdev=1\0" \
76 	"harakiri=0\0" \
77 	"mmcpart=2\0" \
78 	"active_root=root1\0" \
79 	"inactive_root=root2\0" \
80 	"mmcrootfstype=ext4 rootwait\0" \
81 	"nfsopts=nolock\0" \
82 	"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
83 		"::off\0" \
84 	"ip_method=none\0" \
85 	"bootargs_defaults=setenv bootargs " \
86 		"console=${console} " \
87 		"${optargs}\0" \
88 	"mmcargs=run bootargs_defaults;" \
89 		"setenv bootargs ${bootargs} " \
90 		"root=${mmcroot} " \
91 		"rootfstype=${mmcrootfstype} ip=${ip_method}\0" \
92 	"netargs=setenv bootargs console=${console} " \
93 		"${optargs} " \
94 		"root=/dev/nfs " \
95 		"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
96 		"ip=dhcp\0" \
97 	"bootenv=uEnv.txt\0" \
98 	"loadbootenv=if fatload mmc ${mmcdev} ${loadaddr} ${bootenv}; then " \
99 			"echo Loaded environment from ${bootenv}; " \
100 			"run importbootenv; " \
101 		"fi;\0" \
102 	"importbootenv=echo Importing environment variables from uEnv.txt ...; " \
103 		"env import -t $loadaddr $filesize\0" \
104 	"loaduimagefat=fatload mmc ${mmcdev} ${kloadaddr} ${bootfile}\0" \
105 	"loaduimage=ext2load mmc ${mmcdev}:${mmcpart} ${kloadaddr} /boot/${bootfile}\0" \
106 	"loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdtaddr} /boot/${fdtfile}\0" \
107 	"netloaduimage=tftp ${loadaddr} ${bootfile}\0" \
108 	"netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
109 	"mmcboot=echo Booting Linux from ${mmcdevice} ...; " \
110 		"run mmcargs; " \
111 		"if run loadfdt; then " \
112 			"echo device tree detected; " \
113 			"bootm ${kloadaddr} - ${fdtaddr}; " \
114 		"else " \
115 			"bootm ${kloadaddr}; " \
116 		"fi; \0" \
117 	"netboot=echo Booting from network ...; " \
118 		"setenv autoload no; " \
119 		"dhcp; " \
120 		"run netloaduimage; " \
121 		"run netargs; " \
122 		"echo NFS path: ${serverip}:${rootpath};" \
123 		"if run netloadfdt; then " \
124 			"echo device tree detected; " \
125 			"bootm ${loadaddr} - ${fdtaddr}; " \
126 		"else " \
127 			"bootm ${loadaddr}; " \
128 		"fi; \0" \
129 	"emmc_erase=if test ${harakiri} = 1 ; then echo erase emmc ...; setenv mmcdev 1; mmc erase 0 200; reset; fi; \0" \
130 	"mmcpart_gp=mmcpart gp 1 40; \0" \
131 	"mmcpart_enhance=mmcpart enhance 0 64; \0" \
132 	"mmcpart_rel_write=mmcpart rel_write 1f; \0" \
133 	"mmcpart_commit=mmcpart commit 1; \0" \
134 	"mmc_hw_part=run mmcpart_gp; run mmcpart_enhance; run mmcpart_rel_write; run mmcpart_commit; \0" \
135 	"led_success=gpio set 22; \0" \
136 	"fusecmd=mmc dev 1; if mmcpart iscommitted; then echo HW Partitioning already committed; mmcpart list; else run mmc_hw_part; fi; run led_success; \0" \
137 	"uenv_exec=if test -n $uenvcmd; then " \
138 			"echo Running uenvcmd ...; " \
139 			"run uenvcmd; " \
140 		"fi;\0" \
141 	"sd_setup=echo SD/MMC-Card detected on device 0; " \
142 		"setenv mmcdevice SD; " \
143 		"setenv mmcdev 0; " \
144 		"setenv mmcpart 2; " \
145 		"setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0" \
146 	"emmc_setup=echo eMMC detected on device 1; " \
147 		"setenv mmcdevice eMMC; " \
148 		"setenv mmcdev 1; " \
149 		"run emmc_erase; " \
150 		"if test ${active_root} = root2; then " \
151 			"echo Active root is partition 6 (root2); " \
152 			"setenv mmcpart 6; " \
153 		"else " \
154 			"echo Active root is partition 5 (root1); " \
155 			"setenv mmcpart 5; " \
156 		"fi; " \
157 		"setenv mmcroot /dev/mmcblk${mmcdev}p${mmcpart};\0"
158 #endif /* #ifndef CONFIG_SPL_BUILD */
159 
160 #if defined CONFIG_SHC_NETBOOT
161 /* Network Boot */
162 # define CONFIG_BOOTCOMMAND \
163 	"run fusecmd; " \
164 	"if run netboot; then " \
165 		"echo Booting from network; " \
166 	"else " \
167 		"echo ERROR: Cannot boot from network!; " \
168 		"panic; " \
169 	"fi; "
170 
171 #elif defined CONFIG_SHC_SDBOOT /* !defined CONFIG_SHC_NETBOOT */
172 /* SD-Card Boot */
173 # define CONFIG_BOOTCOMMAND \
174 	"if mmc dev 0; mmc rescan; then " \
175 		"run sd_setup; " \
176 	"else " \
177 		"echo ERROR: SD/MMC-Card not detected!; " \
178 		"panic; " \
179 	"fi; " \
180 	"if run loaduimage; then " \
181 		"echo Bootable SD/MMC-Card inserted, booting from it!; " \
182 		"run mmcboot; " \
183 	"else " \
184 		"echo ERROR: Unable to load uImage from SD/MMC-Card!; " \
185 		"panic; " \
186 	"fi; "
187 
188 #elif defined CONFIG_SHC_ICT
189 /* ICT adapter boots only u-boot and does HW partitioning */
190 # define CONFIG_BOOTCOMMAND \
191 	"if mmc dev 0; mmc rescan; then " \
192 		"run sd_setup; " \
193 	"else " \
194 		"echo ERROR: SD/MMC-Card not detected!; " \
195 		"panic; " \
196 	"fi; " \
197 	"run fusecmd; "
198 
199 #else /* !defined CONFIG_SHC_NETBOOT, !defined CONFIG_SHC_SDBOOT */
200 /* Regular Boot from internal eMMC */
201 # define CONFIG_BOOTCOMMAND \
202 	"if mmc dev 1; mmc rescan; then " \
203 		"run emmc_setup; " \
204 	"else " \
205 		"echo ERROR: eMMC device not detected!; " \
206 		"panic; " \
207 	"fi; " \
208 	"if run loaduimage; then " \
209 		"run mmcboot; " \
210 	"else " \
211 		"echo ERROR Unable to load uImage from eMMC!; " \
212 		"echo Performing Rollback!; " \
213 		"setenv _active_ ${active_root}; " \
214 		"setenv _inactive_ ${inactive_root}; " \
215 		"setenv active_root ${_inactive_}; " \
216 		"setenv inactive_root ${_active_}; " \
217 		"saveenv; " \
218 		"reset; " \
219 	"fi; "
220 
221 #endif /* Regular Boot */
222 
223 /* NS16550 Configuration */
224 #define CONFIG_SYS_NS16550_COM1		0x44e09000	/* UART0 */
225 #define CONFIG_SYS_NS16550_COM2		0x48022000	/* UART1 */
226 #define CONFIG_SYS_NS16550_COM3		0x48024000	/* UART2 */
227 #define CONFIG_SYS_NS16550_COM4		0x481a6000	/* UART3 */
228 #define CONFIG_SYS_NS16550_COM5		0x481a8000	/* UART4 */
229 #define CONFIG_SYS_NS16550_COM6		0x481aa000	/* UART5 */
230 
231 /* PMIC support */
232 #define CONFIG_POWER_TPS65217
233 
234 /* SPL */
235 
236 /*
237  * Disable MMC DM for SPL build and can be re-enabled after adding
238  * DM support in SPL
239  */
240 #ifdef CONFIG_SPL_BUILD
241 #undef CONFIG_DM_MMC
242 #undef CONFIG_TIMER
243 #endif
244 
245 #define CONFIG_BOOTP_DEFAULT
246 #define CONFIG_BOOTP_DNS2
247 #define CONFIG_BOOTP_SEND_HOSTNAME
248 #define CONFIG_NET_RETRY_COUNT         10
249 #define CONFIG_PHY_SMSC
250 
251 /* I2C configuration */
252 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Main EEPROM */
253 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
254 #define CONFIG_SYS_I2C_SPEED		400000
255 #define CONFIG_SYS_I2C_SLAVE		1
256 #endif	/* ! __CONFIG_AM335X_SHC_H */
257