1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2014 Soeren Moch <smoch@web.de> 4 * 5 * Configuration settings for the TBS2910 MatrixARM board. 6 */ 7 8 #ifndef __TBS2910_CONFIG_H 9 #define __TBS2910_CONFIG_H 10 11 #include "mx6_common.h" 12 13 /* General configuration */ 14 15 #define CONFIG_MACH_TYPE 3980 16 17 #define CONFIG_SYS_HZ 1000 18 19 #define CONFIG_IMX_THERMAL 20 21 /* Physical Memory Map */ 22 #define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR 23 24 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 25 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 26 #define CONFIG_SYS_INIT_SP_OFFSET \ 27 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 28 #define CONFIG_SYS_INIT_SP_ADDR \ 29 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 30 31 #define CONFIG_SYS_MALLOC_LEN (128 * 1024 * 1024) 32 33 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 34 #define CONFIG_SYS_MEMTEST_END \ 35 (CONFIG_SYS_MEMTEST_START + 500 * 1024 * 1024) 36 37 #define CONFIG_SYS_BOOTMAPSZ 0x10000000 38 39 /* Serial console */ 40 #define CONFIG_MXC_UART 41 #define CONFIG_MXC_UART_BASE UART1_BASE /* select UART1/UART2 */ 42 43 /* Framebuffer */ 44 #ifdef CONFIG_VIDEO 45 #define CONFIG_VIDEO_BMP_RLE8 46 #define CONFIG_IMX_HDMI 47 #define CONFIG_IMX_VIDEO_SKIP 48 #endif 49 50 /* PCI */ 51 #ifdef CONFIG_CMD_PCI 52 #define CONFIG_PCI_SCAN_SHOW 53 #define CONFIG_PCIE_IMX 54 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 55 #endif 56 57 /* SATA */ 58 #ifdef CONFIG_CMD_SATA 59 #define CONFIG_SYS_SATA_MAX_DEVICE 1 60 #define CONFIG_DWC_AHSATA_PORT_ID 0 61 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 62 #define CONFIG_LBA48 63 #define CONFIG_SYS_64BIT_LBA 64 #endif 65 66 /* USB */ 67 #ifdef CONFIG_CMD_USB 68 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 69 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 70 #ifdef CONFIG_CMD_USB_MASS_STORAGE 71 #define CONFIG_USBD_HS 72 #endif /* CONFIG_CMD_USB_MASS_STORAGE */ 73 #endif /* CONFIG_CMD_USB */ 74 75 /* Environment organization */ 76 #define CONFIG_SYS_MMC_ENV_DEV 2 /* overwritten on SD boot */ 77 #define CONFIG_SYS_MMC_ENV_PART 1 /* overwritten on SD boot */ 78 #define CONFIG_ENV_OVERWRITE 79 80 #define CONFIG_BOARD_SIZE_LIMIT 392192 /* (CONFIG_ENV_OFFSET - 1024) */ 81 82 #define CONFIG_EXTRA_ENV_SETTINGS \ 83 "bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \ 84 "bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M@60 " \ 85 "video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \ 86 "bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \ 87 "bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \ 88 "${bootargs_mmc3}\0" \ 89 "bootargs_upd=setenv bootargs console=ttymxc0,115200 " \ 90 "rdinit=/sbin/init enable_wait_mode=off\0" \ 91 "bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \ 92 "mmc read 0x10800000 0x800 0x4000; bootm 0x10800000\0" \ 93 "bootcmd_up1=load mmc 1 0x10800000 uImage\0" \ 94 "bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \ 95 "run bootargs_upd; " \ 96 "bootm 0x10800000 0x10d00000\0" \ 97 "console=ttymxc0\0" \ 98 "fan=gpio set 92\0" \ 99 "set_con_serial=setenv stdout serial; " \ 100 "setenv stderr serial\0" \ 101 "set_con_hdmi=setenv stdout serial,vga; " \ 102 "setenv stderr serial,vga\0" \ 103 "stderr=serial,vga\0" \ 104 "stdin=serial,usbkbd\0" \ 105 "stdout=serial,vga\0" 106 107 #define CONFIG_BOOTCOMMAND \ 108 "mmc rescan; " \ 109 "if run bootcmd_up1; then " \ 110 "run bootcmd_up2; " \ 111 "else " \ 112 "run bootcmd_mmc; " \ 113 "fi" 114 115 #endif /* __TBS2910_CONFIG_H * */ 116