1 /*------------------------------------------------------------------------ 2 * smc9000.h 3 * 4 * Copyright (C) 1998 by Daniel Engstr�m 5 * Copyright (C) 1996 by Erik Stahlman 6 * 7 * This software may be used and distributed according to the terms 8 * of the GNU Public License, incorporated herein by reference. 9 * 10 * This file contains register information and access macros for 11 * the SMC91xxx chipset. 12 * 13 * Information contained in this file was obtained from the SMC91C94 14 * manual from SMC. To get a copy, if you really want one, you can find 15 * information under www.smsc.com in the components division. 16 * ( this thanks to advice from Donald Becker ). 17 * 18 * Authors 19 * Daniel Engstr�m <daniel.engstrom@riksnett.no> 20 * Erik Stahlman <erik@vt.edu> 21 * 22 * History 23 * 96-01-06 Erik Stahlman moved definitions here from main .c 24 * file 25 * 96-01-19 Erik Stahlman polished this up some, and added 26 * better error handling 27 * 98-09-25 Daniel Engstr�m adjusted for Etherboot 28 * 98-09-27 Daniel Engstr�m moved some static strings back to the 29 * main .c file 30 * --------------------------------------------------------------------------*/ 31 #ifndef _SMC9000_H_ 32 # define _SMC9000_H_ 33 34 /* I want some simple types */ 35 typedef unsigned char byte; 36 typedef unsigned short word; 37 typedef unsigned long int dword; 38 39 /*--------------------------------------------------------------- 40 * 41 * A description of the SMC registers is probably in order here, 42 * although for details, the SMC datasheet is invaluable. 43 * 44 * Basically, the chip has 4 banks of registers ( 0 to 3 ), which 45 * are accessed by writing a number into the BANK_SELECT register 46 * ( I also use a SMC_SELECT_BANK macro for this ). 47 * 48 * The banks are configured so that for most purposes, bank 2 is all 49 * that is needed for simple run time tasks. 50 * ----------------------------------------------------------------------*/ 51 52 /* 53 * Bank Select Register: 54 * 55 * yyyy yyyy 0000 00xx 56 * xx = bank number 57 * yyyy yyyy = 0x33, for identification purposes. 58 */ 59 #define BANK_SELECT 14 60 61 /* BANK 0 */ 62 63 #define TCR 0 /* transmit control register */ 64 #define TCR_ENABLE 0x0001 /* if this is 1, we can transmit */ 65 #define TCR_FDUPLX 0x0800 /* receive packets sent out */ 66 #define TCR_STP_SQET 0x1000 /* stop transmitting if Signal quality error */ 67 #define TCR_MON_CNS 0x0400 /* monitors the carrier status */ 68 #define TCR_PAD_ENABLE 0x0080 /* pads short packets to 64 bytes */ 69 70 #define TCR_CLEAR 0 /* do NOTHING */ 71 /* the normal settings for the TCR register : */ 72 #define TCR_NORMAL (TCR_ENABLE | TCR_PAD_ENABLE) 73 74 75 #define EPH_STATUS 2 76 #define ES_LINK_OK 0x4000 /* is the link integrity ok ? */ 77 78 #define RCR 4 79 #define RCR_SOFTRESET 0x8000 /* resets the chip */ 80 #define RCR_STRIP_CRC 0x200 /* strips CRC */ 81 #define RCR_ENABLE 0x100 /* IFF this is set, we can receive packets */ 82 #define RCR_ALMUL 0x4 /* receive all multicast packets */ 83 #define RCR_PROMISC 0x2 /* enable promiscuous mode */ 84 85 /* the normal settings for the RCR register : */ 86 #define RCR_NORMAL (RCR_STRIP_CRC | RCR_ENABLE) 87 #define RCR_CLEAR 0x0 /* set it to a base state */ 88 89 #define COUNTER 6 90 #define MIR 8 91 #define MCR 10 92 /* 12 is reserved */ 93 94 /* BANK 1 */ 95 #define CONFIG 0 96 #define CFG_AUI_SELECT 0x100 97 #define BASE 2 98 #define ADDR0 4 99 #define ADDR1 6 100 #define ADDR2 8 101 #define GENERAL 10 102 #define CONTROL 12 103 #define CTL_POWERDOWN 0x2000 104 #define CTL_LE_ENABLE 0x80 105 #define CTL_CR_ENABLE 0x40 106 #define CTL_TE_ENABLE 0x0020 107 #define CTL_AUTO_RELEASE 0x0800 108 #define CTL_EPROM_ACCESS 0x0003 /* high if Eprom is being read */ 109 110 /* BANK 2 */ 111 #define MMU_CMD 0 112 #define MC_BUSY 1 /* only readable bit in the register */ 113 #define MC_NOP 0 114 #define MC_ALLOC 0x20 /* or with number of 256 byte packets */ 115 #define MC_RESET 0x40 116 #define MC_REMOVE 0x60 /* remove the current rx packet */ 117 #define MC_RELEASE 0x80 /* remove and release the current rx packet */ 118 #define MC_FREEPKT 0xA0 /* Release packet in PNR register */ 119 #define MC_ENQUEUE 0xC0 /* Enqueue the packet for transmit */ 120 121 #define PNR_ARR 2 122 #define FIFO_PORTS 4 123 124 #define FP_RXEMPTY 0x8000 125 #define FP_TXEMPTY 0x80 126 127 #define POINTER 6 128 #define PTR_READ 0x2000 129 #define PTR_RCV 0x8000 130 #define PTR_AUTOINC 0x4000 131 #define PTR_AUTO_INC 0x0040 132 133 #define DATA_1 8 134 #define DATA_2 10 135 #define INTERRUPT 12 136 137 #define INT_MASK 13 138 #define IM_RCV_INT 0x1 139 #define IM_TX_INT 0x2 140 #define IM_TX_EMPTY_INT 0x4 141 #define IM_ALLOC_INT 0x8 142 #define IM_RX_OVRN_INT 0x10 143 #define IM_EPH_INT 0x20 144 #define IM_ERCV_INT 0x40 /* not on SMC9192 */ 145 146 /* BANK 3 */ 147 #define MULTICAST1 0 148 #define MULTICAST2 2 149 #define MULTICAST3 4 150 #define MULTICAST4 6 151 #define MGMT 8 152 #define REVISION 10 /* ( hi: chip id low: rev # ) */ 153 154 155 /* this is NOT on SMC9192 */ 156 #define ERCV 12 157 158 /* Note that 9194 and 9196 have the smame chip id, 159 * the 9196 will have revisions starting at 6 */ 160 #define CHIP_9190 3 161 #define CHIP_9194 4 162 #define CHIP_9195 5 163 #define CHIP_9196 4 164 #define CHIP_91100 7 165 #define CHIP_91100FD 8 166 167 #define REV_9196 6 168 169 /* 170 * Transmit status bits 171 */ 172 #define TS_SUCCESS 0x0001 173 #define TS_LOSTCAR 0x0400 174 #define TS_LATCOL 0x0200 175 #define TS_16COL 0x0010 176 177 /* 178 * Receive status bits 179 */ 180 #define RS_ALGNERR 0x8000 181 #define RS_BADCRC 0x2000 182 #define RS_ODDFRAME 0x1000 183 #define RS_TOOLONG 0x0800 184 #define RS_TOOSHORT 0x0400 185 #define RS_MULTICAST 0x0001 186 #define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT) 187 188 189 /*------------------------------------------------------------------------- 190 * I define some macros to make it easier to do somewhat common 191 * or slightly complicated, repeated tasks. 192 --------------------------------------------------------------------------*/ 193 194 /* select a register bank, 0 to 3 */ 195 196 #define SMC_SELECT_BANK(x, y) { _outw( y, x + BANK_SELECT ); } 197 198 /* define a small delay for the reset */ 199 #define SMC_DELAY(x) { inw( x + RCR );\ 200 inw( x + RCR );\ 201 inw( x + RCR ); } 202 203 204 #endif /* _SMC_9000_H_ */ 205 206