• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1 /*
2  * linux/arch/arm/mach-at91/board-dk.c
3  *
4  *  Copyright (C) 2005 SAN People
5  *
6  *  Epson S1D framebuffer glue code is:
7  *     Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
8  *
9  * This program is free software; you can redistribute it and/or modify
10  * it under the terms of the GNU General Public License as published by
11  * the Free Software Foundation; either version 2 of the License, or
12  * (at your option) any later version.
13  *
14  * This program is distributed in the hope that it will be useful,
15  * but WITHOUT ANY WARRANTY; without even the implied warranty of
16  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
17  * GNU General Public License for more details.
18  *
19  * You should have received a copy of the GNU General Public License
20  * along with this program; if not, write to the Free Software
21  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
22  */
23 
24 #include <linux/types.h>
25 #include <linux/init.h>
26 #include <linux/mm.h>
27 #include <linux/module.h>
28 #include <linux/platform_device.h>
29 #include <linux/spi/spi.h>
30 #include <linux/mtd/physmap.h>
31 
32 #include <asm/setup.h>
33 #include <asm/mach-types.h>
34 #include <asm/irq.h>
35 
36 #include <asm/mach/arch.h>
37 #include <asm/mach/map.h>
38 #include <asm/mach/irq.h>
39 
40 #include <mach/hardware.h>
41 #include <mach/board.h>
42 #include <mach/gpio.h>
43 #include <mach/at91rm9200_mc.h>
44 
45 #include "generic.h"
46 
47 
dk_map_io(void)48 static void __init dk_map_io(void)
49 {
50 	/* Initialize processor: 18.432 MHz crystal */
51 	at91rm9200_initialize(18432000, AT91RM9200_BGA);
52 
53 	/* Setup the LEDs */
54 	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
55 
56 	/* DBGU on ttyS0. (Rx & Tx only) */
57 	at91_register_uart(0, 0, 0);
58 
59 	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
60 	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
61 			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
62 			   | ATMEL_UART_RI);
63 
64 	/* set serial console to ttyS0 (ie, DBGU) */
65 	at91_set_serial_console(0);
66 }
67 
dk_init_irq(void)68 static void __init dk_init_irq(void)
69 {
70 	at91rm9200_init_interrupts(NULL);
71 }
72 
73 static struct at91_eth_data __initdata dk_eth_data = {
74 	.phy_irq_pin	= AT91_PIN_PC4,
75 	.is_rmii	= 1,
76 };
77 
78 static struct at91_usbh_data __initdata dk_usbh_data = {
79 	.ports		= 2,
80 };
81 
82 static struct at91_udc_data __initdata dk_udc_data = {
83 	.vbus_pin	= AT91_PIN_PD4,
84 	.pullup_pin	= AT91_PIN_PD5,
85 };
86 
87 static struct at91_cf_data __initdata dk_cf_data = {
88 	.det_pin	= AT91_PIN_PB0,
89 	.rst_pin	= AT91_PIN_PC5,
90 	// .irq_pin	= ... not connected
91 	// .vcc_pin	= ... always powered
92 };
93 
94 static struct at91_mmc_data __initdata dk_mmc_data = {
95 	.slot_b		= 0,
96 	.wire4		= 1,
97 };
98 
99 static struct spi_board_info dk_spi_devices[] = {
100 	{	/* DataFlash chip */
101 		.modalias	= "mtd_dataflash",
102 		.chip_select	= 0,
103 		.max_speed_hz	= 15 * 1000 * 1000,
104 	},
105 	{	/* UR6HCPS2-SP40 PS2-to-SPI adapter */
106 		.modalias	= "ur6hcps2",
107 		.chip_select	= 1,
108 		.max_speed_hz	= 250 *  1000,
109 	},
110 	{	/* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */
111 		.modalias	= "tlv1504",
112 		.chip_select	= 2,
113 		.max_speed_hz	= 20 * 1000 * 1000,
114 	},
115 #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
116 	{	/* DataFlash card */
117 		.modalias	= "mtd_dataflash",
118 		.chip_select	= 3,
119 		.max_speed_hz	= 15 * 1000 * 1000,
120 	}
121 #endif
122 };
123 
124 static struct i2c_board_info __initdata dk_i2c_devices[] = {
125 	{
126 		I2C_BOARD_INFO("ics1523", 0x26),
127 	},
128 	{
129 		I2C_BOARD_INFO("x9429", 0x28),
130 	},
131 	{
132 		I2C_BOARD_INFO("24c1024", 0x50),
133 	}
134 };
135 
136 static struct mtd_partition __initdata dk_nand_partition[] = {
137 	{
138 		.name	= "NAND Partition 1",
139 		.offset	= 0,
140 		.size	= MTDPART_SIZ_FULL,
141 	},
142 };
143 
nand_partitions(int size,int * num_partitions)144 static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
145 {
146 	*num_partitions = ARRAY_SIZE(dk_nand_partition);
147 	return dk_nand_partition;
148 }
149 
150 static struct atmel_nand_data __initdata dk_nand_data = {
151 	.ale		= 22,
152 	.cle		= 21,
153 	.det_pin	= AT91_PIN_PB1,
154 	.rdy_pin	= AT91_PIN_PC2,
155 	// .enable_pin	= ... not there
156 	.partition_info	= nand_partitions,
157 };
158 
159 #define DK_FLASH_BASE	AT91_CHIPSELECT_0
160 #define DK_FLASH_SIZE	SZ_2M
161 
162 static struct physmap_flash_data dk_flash_data = {
163 	.width		= 2,
164 };
165 
166 static struct resource dk_flash_resource = {
167 	.start		= DK_FLASH_BASE,
168 	.end		= DK_FLASH_BASE + DK_FLASH_SIZE - 1,
169 	.flags		= IORESOURCE_MEM,
170 };
171 
172 static struct platform_device dk_flash = {
173 	.name		= "physmap-flash",
174 	.id		= 0,
175 	.dev		= {
176 				.platform_data	= &dk_flash_data,
177 			},
178 	.resource	= &dk_flash_resource,
179 	.num_resources	= 1,
180 };
181 
182 static struct gpio_led dk_leds[] = {
183 	{
184 		.name			= "led0",
185 		.gpio			= AT91_PIN_PB2,
186 		.active_low		= 1,
187 		.default_trigger	= "heartbeat",
188 	}
189 };
190 
dk_board_init(void)191 static void __init dk_board_init(void)
192 {
193 	/* Serial */
194 	at91_add_device_serial();
195 	/* Ethernet */
196 	at91_add_device_eth(&dk_eth_data);
197 	/* USB Host */
198 	at91_add_device_usbh(&dk_usbh_data);
199 	/* USB Device */
200 	at91_add_device_udc(&dk_udc_data);
201 	at91_set_multi_drive(dk_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
202 	/* Compact Flash */
203 	at91_add_device_cf(&dk_cf_data);
204 	/* I2C */
205 	at91_add_device_i2c(dk_i2c_devices, ARRAY_SIZE(dk_i2c_devices));
206 	/* SPI */
207 	at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
208 #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
209 	/* DataFlash card */
210 	at91_set_gpio_output(AT91_PIN_PB7, 0);
211 #else
212 	/* MMC */
213 	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
214 	at91_add_device_mmc(0, &dk_mmc_data);
215 #endif
216 	/* NAND */
217 	at91_add_device_nand(&dk_nand_data);
218 	/* NOR Flash */
219 	platform_device_register(&dk_flash);
220 	/* LEDs */
221 	at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
222 	/* VGA */
223 //	dk_add_device_video();
224 }
225 
226 MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
227 	/* Maintainer: SAN People/Atmel */
228 	.phys_io	= AT91_BASE_SYS,
229 	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
230 	.boot_params	= AT91_SDRAM_BASE + 0x100,
231 	.timer		= &at91rm9200_timer,
232 	.map_io		= dk_map_io,
233 	.init_irq	= dk_init_irq,
234 	.init_machine	= dk_board_init,
235 MACHINE_END
236