• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1 /*
2  * linux/arch/arm/mach-at91/board-usb-a9263.c
3  *
4  *  Copyright (C) 2005 SAN People
5  *  Copyright (C) 2007 Atmel Corporation.
6  *  Copyright (C) 2007 Calao-systems
7  *
8  * This program is free software; you can redistribute it and/or modify
9  * it under the terms of the GNU General Public License as published by
10  * the Free Software Foundation; either version 2 of the License, or
11  * (at your option) any later version.
12  *
13  * This program is distributed in the hope that it will be useful,
14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
16  * GNU General Public License for more details.
17  *
18  * You should have received a copy of the GNU General Public License
19  * along with this program; if not, write to the Free Software
20  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
21  */
22 
23 #include <linux/types.h>
24 #include <linux/init.h>
25 #include <linux/mm.h>
26 #include <linux/module.h>
27 #include <linux/platform_device.h>
28 #include <linux/spi/spi.h>
29 #include <linux/gpio_keys.h>
30 #include <linux/input.h>
31 
32 #include <asm/setup.h>
33 #include <asm/mach-types.h>
34 #include <asm/irq.h>
35 
36 #include <asm/mach/arch.h>
37 #include <asm/mach/map.h>
38 #include <asm/mach/irq.h>
39 
40 #include <mach/hardware.h>
41 #include <mach/board.h>
42 #include <mach/gpio.h>
43 #include <mach/at91sam9_smc.h>
44 #include <mach/at91_shdwc.h>
45 
46 #include "sam9_smc.h"
47 #include "generic.h"
48 
49 
ek_map_io(void)50 static void __init ek_map_io(void)
51 {
52 	/* Initialize processor: 12.00 MHz crystal */
53 	at91sam9263_initialize(12000000);
54 
55 	/* DGBU on ttyS0. (Rx & Tx only) */
56 	at91_register_uart(0, 0, 0);
57 
58 	/* set serial console to ttyS0 (ie, DBGU) */
59 	at91_set_serial_console(0);
60 }
61 
ek_init_irq(void)62 static void __init ek_init_irq(void)
63 {
64 	at91sam9263_init_interrupts(NULL);
65 }
66 
67 
68 /*
69  * USB Host port
70  */
71 static struct at91_usbh_data __initdata ek_usbh_data = {
72 	.ports		= 2,
73 };
74 
75 /*
76  * USB Device port
77  */
78 static struct at91_udc_data __initdata ek_udc_data = {
79 	.vbus_pin	= AT91_PIN_PB11,
80 	.pullup_pin	= 0,		/* pull-up driven by UDC */
81 };
82 
83 /*
84  * SPI devices.
85  */
86 static struct spi_board_info ek_spi_devices[] = {
87 #if !defined(CONFIG_MMC_AT91)
88 	{	/* DataFlash chip */
89 		.modalias	= "mtd_dataflash",
90 		.chip_select	= 0,
91 		.max_speed_hz	= 15 * 1000 * 1000,
92 		.bus_num	= 0,
93 	}
94 #endif
95 };
96 
97 /*
98  * MACB Ethernet device
99  */
100 static struct at91_eth_data __initdata ek_macb_data = {
101 	.phy_irq_pin	= AT91_PIN_PE31,
102 	.is_rmii	= 1,
103 };
104 
105 /*
106  * NAND flash
107  */
108 static struct mtd_partition __initdata ek_nand_partition[] = {
109 	{
110 		.name	= "Linux Kernel",
111 		.offset	= 0,
112 		.size	= SZ_16M,
113 	},
114 	{
115 		.name	= "Root FS",
116 		.offset	= MTDPART_OFS_NXTBLK,
117 		.size	= 120 * SZ_1M,
118 	},
119 	{
120 		.name	= "FS",
121 		.offset	= MTDPART_OFS_NXTBLK,
122 		.size	= 120 * SZ_1M,
123 	}
124 };
125 
nand_partitions(int size,int * num_partitions)126 static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
127 {
128 	*num_partitions = ARRAY_SIZE(ek_nand_partition);
129 	return ek_nand_partition;
130 }
131 
132 static struct atmel_nand_data __initdata ek_nand_data = {
133 	.ale		= 21,
134 	.cle		= 22,
135 //	.det_pin	= ... not connected
136 	.rdy_pin	= AT91_PIN_PA22,
137 	.enable_pin	= AT91_PIN_PD15,
138 	.partition_info	= nand_partitions,
139 };
140 
141 static struct sam9_smc_config __initdata ek_nand_smc_config = {
142 	.ncs_read_setup		= 0,
143 	.nrd_setup		= 1,
144 	.ncs_write_setup	= 0,
145 	.nwe_setup		= 1,
146 
147 	.ncs_read_pulse		= 3,
148 	.nrd_pulse		= 3,
149 	.ncs_write_pulse	= 3,
150 	.nwe_pulse		= 3,
151 
152 	.read_cycle		= 5,
153 	.write_cycle		= 5,
154 
155 	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
156 	.tdf_cycles		= 2,
157 };
158 
ek_add_device_nand(void)159 static void __init ek_add_device_nand(void)
160 {
161 	/* configure chip-select 3 (NAND) */
162 	sam9_smc_configure(3, &ek_nand_smc_config);
163 
164 	at91_add_device_nand(&ek_nand_data);
165 }
166 
167 
168 /*
169  * GPIO Buttons
170  */
171 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
172 static struct gpio_keys_button ek_buttons[] = {
173 	{	/* USER PUSH BUTTON */
174 		.code		= KEY_ENTER,
175 		.gpio		= AT91_PIN_PB10,
176 		.active_low	= 1,
177 		.desc		= "user_pb",
178 		.wakeup		= 1,
179 	}
180 };
181 
182 static struct gpio_keys_platform_data ek_button_data = {
183 	.buttons	= ek_buttons,
184 	.nbuttons	= ARRAY_SIZE(ek_buttons),
185 };
186 
187 static struct platform_device ek_button_device = {
188 	.name		= "gpio-keys",
189 	.id		= -1,
190 	.num_resources	= 0,
191 	.dev		= {
192 		.platform_data	= &ek_button_data,
193 	}
194 };
195 
ek_add_device_buttons(void)196 static void __init ek_add_device_buttons(void)
197 {
198 	at91_set_GPIO_periph(AT91_PIN_PB10, 1);	/* user push button, pull up enabled */
199 	at91_set_deglitch(AT91_PIN_PB10, 1);
200 
201 	platform_device_register(&ek_button_device);
202 }
203 #else
ek_add_device_buttons(void)204 static void __init ek_add_device_buttons(void) {}
205 #endif
206 
207 /*
208  * LEDs
209  */
210 static struct gpio_led ek_leds[] = {
211 	{	/* user_led (green) */
212 		.name			= "user_led",
213 		.gpio			= AT91_PIN_PB21,
214 		.active_low		= 1,
215 		.default_trigger	= "heartbeat",
216 	}
217 };
218 
219 
ek_board_init(void)220 static void __init ek_board_init(void)
221 {
222 	/* Serial */
223 	at91_add_device_serial();
224 	/* USB Host */
225 	at91_add_device_usbh(&ek_usbh_data);
226 	/* USB Device */
227 	at91_add_device_udc(&ek_udc_data);
228 	/* SPI */
229 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
230 	/* Ethernet */
231 	at91_add_device_eth(&ek_macb_data);
232 	/* NAND */
233 	ek_add_device_nand();
234 	/* I2C */
235 	at91_add_device_i2c(NULL, 0);
236 	/* Push Buttons */
237 	ek_add_device_buttons();
238 	/* LEDs */
239 	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
240 	/* shutdown controller, wakeup button (5 msec low) */
241 	at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
242 				| AT91_SHDW_RTTWKEN);
243 }
244 
245 MACHINE_START(USB_A9263, "CALAO USB_A9263")
246 	/* Maintainer: calao-systems */
247 	.phys_io	= AT91_BASE_SYS,
248 	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
249 	.boot_params	= AT91_SDRAM_BASE + 0x100,
250 	.timer		= &at91sam926x_timer,
251 	.map_io		= ek_map_io,
252 	.init_irq	= ek_init_irq,
253 	.init_machine	= ek_board_init,
254 MACHINE_END
255